Uniform Industrial UIC680VG Reader Instructions
- June 5, 2024
- Uniform Industrial
Table of Contents
Uniform Industrial UIC680VG Reader
Model: UIC680VG
Product Specifications
| Item | SPEC |
|---|---|
| Processor | Microchip ATSAMA5D28C-CU |
Memory
| DDR3L SDRAM RAM 256Mbytes
-40~95 800 MHz
Storage| Micron NAND Flash 256M
OS Version| Linux 4.19.56 (Microchip Linux4sam v6.1)
SAM
| 4 SAMs (5V/3.3V/1.8V)
can be inserted directly (no need to disassembly the SAM board module)
Indicators
| EMV LEDs x4 Green
(reserve LED signal to extend LED connector on IO board) Logo LED x4 RGB
Provide control cmd for customers( RGB breathing light for tapping card
indicator)
Audio| Buzzer Sound Pressure Level: 70 dB at 10cm(default)
I/O Connector|
Connector x1
(8P wires, pitch 1.25)
| ****
USB/RS232 cable selection
Connector x1
(2P wires, pitch 1.25)
| ****
battery replacement purpose
Connector x1| SAM board
Debug port| 3pin connector on IOBD
Power input| 5V DC/500mA
Communication| USB/RS232
Payment Reader
| RFID Reader
ISO 14443 Type A/B/Mifare ISO18092 NFC-IP1
JIS X6319-4 (FeliCa)
ISO15693
Reliability
Coin Battery Life
| 5 years
(Additional connector while battery replacement)
Environmental
| Operating -25 to 70℃ Storage -25 to 80℃
Humidity : 5% – 95% (none-condensing)
MTBF| 100,000 Hours
ESD| ±8KV contact/±15KV Air
IP/IK Rating| IP65/IK9
UV exposure resistance| Half daylight.
Drop resistance| 92cm
| ****
Power management
| Power on <500mA(4.5V)
Idle <100mA(RFID off) : 80mA
---|---|---
Installation guide
Installation guide(USB Interface)
1| Plug the USB cable to the USB port of PC.
2| Install the driver
|
FCC STATEMENT
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment. This device
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
RTC Warning :
“Caurtion: Risk of explosion if the battery is replaced by an incorrect type”
| Company Name | Uniform Industrial Corp. |
|---|---|
| Company Addr | 2901 Bayview Dr, Fremont, CA 94538 |
For CE: 1F, No.1, Lane 15, Ziqiang St., Tucheng Dist., New Taipei City 236, Taiwan
Tel No| (510)4386799
Declaration of the Presence Condition of the Restricted Substances Marking