kmart 42666394 Queen Air Bed with Pump Instruction Manual

Kmart 42666394 Queen Air Bed with Pump

Important Safety Guideline

Please read, understand and follow all instructions prior to using.
To enhance the enjoyment of your Air Bed and protect the safety of the operator using the product, ALWAYS STRICTLY OBSERVE the following important safety points. The following important points should be read and understood before using this product:

1. WARNING: To prevent possible electric shock, do not attempt to plug in power cord with wet hands.
2. WARNING: To prevent possible electric shock, connect power cord into a grounded receptacle protected by a ground-fault circuit interrupter (GFCI).
3. WARNING: To prevent possible electric shock, never use a damaged or frayed power cord. If the supply cord is damaged, it must be replaced by the manufactured or its service agent or a similarly qualified person in order to avoid a hazard.
4. WARNING: Do not use extension power cords with this product.
5. WARNING: Only for indoor household use. Keep away from fire.
6. WARNING: In order to reduce the risk of electric shock, do not expose to rain. And store indoors.
7. RISK OF COMBUSTION: Do not place the airbed against or near any open flames, heaters, furnaces or other hot objects.
8. IMPORTANT: Do not operate electric pump for more than 5 minutes at one time, take 20 minutes break between uses, as overheating may occur and pump will automatically shut off. It will be ready to use after it has cooled down. This automatic shut off is for your safety. Unplug electrical power cord when not in use.
9. WARNING: Do not obstruct the air passage opening or insert any objects into the opening at any time.
10.  WARNING: Do not stand on, jump on or use the airbed as a trampoline. Always supervise children near the airbed.
11. WARNING: This product is not a raft or flotation device. Do not use near or on water.
12. WARNING: Children must not be left unattended when using the airbed. Use only under adult competent supervision.
13. WARNING: The storage bag is not a toy. To avoid danger of suffocation, keep the airbed storage bag or any other bags away from babies and children. Fold up the bag and store away from children when not in use.
14. WARNING: Keep pets away from the airbed. Pets may tear or puncture the airbed.
15. IMPORTANT: Make sure the area is flat, smooth, even and free of sharp objects that can puncture the airbed. Do not set up the airbed near stairs, doors, drops, sharp edges or breakables.
16.  IMPORTANT: To minimize any chance of rolling, tipping or swaying, avoid sleeping on the edge of the airbed. Edges provide less support than the middle of the airbed.
17. IMPORTANT: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Inflation instructions

1. Make sure the optional inflation air valve is securely closed.
2. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit interrupter outlet). Please check the correct voltage! See Fig. (1)
3. Turn the control dial clockwise until arrow points to the inflation mark ( See Fig. (2)
4. When the airbed is fully inflated to the desired firmness, turn the control dial counter-clockwise until arrow points to the “OFF”. See Fig. (3)
5. Lie down on the airbed to test the firmness.
6. If the sleeping surface is too hard, adjust the firmness by continuously turning the control dial counter-clockwise gradually until air begins to exit through the air passage. Then turn the control dial clockwise until arrow points to the “OFF” when the desired firmness is achieved. If the airbed becomes too soft, please repeat step 3 thru 5 as necessary.

Deflation instructions

1. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit interrupter outlet). Please check the correct voltage! See Fig. (1)
2. Turn the control dial counter-clockwise until arrow points to the deflation mark ( ). See below Fig. (4)
3. When all air is removed from the airbed, turn the control dial clockwise until arrow points to the “OFF”. See below Fig. (3)
4. When the airbed is completely deflated, begin rolling the airbed from the foot of the airbed towards the head of the airbed where the pump is located. To ensure the airbed is fully deflated, repeat steps 2 thru 3.
5. Disconnect the AC line cord from the wall socket.

Inflation option
If the electric pump is not available then a conventional foot or manually operated air pump can be connected to the optional inflation valve for inflation. See below fig (5).

1. Remove the valve totally from out of the valve insertion, and then pull the stopper out of the valve extension. Inflate the product by air pumps. Blow in sufficient air in order to fill up the chamber to the full extent. Do not use air compressor or high pressure pumps. Do not over inflate: excessive inflation of the air chambers can cause the chamber to burst or cause damage to the welding seams.
2. Close the valve by firmly inserting the stopper and press the valve into the chamber until the valve sits flush with the chamber.

Storage and Maintenance

1. Clean the product with clear water, then leave it in a shady and cool place for airing, fold it into the original package and store indoors for next use. Caution: Do not use the alkali or acid detergent to clean product! Do not leave product exposed under sunlight directly because it will shorten the lifespan of the product.
2. Fold the airbed loosely and avoid sharp bends, corners and creases which can damage the airbed.
3. No specific maintenance is required for the built-in electric pump.
4. Place the airbed inside the storage bag and store in a dry and room temperature location indoors. Do not store in an area where it is likely to be exposed to extreme temperature.\

Repair Patch Instructions
(Small pinhole and small puncture leaks can be repaired with the included repair patch)

1. Locate the leak.
2. Deflate the airbed.
3. Clean the area surrounding the puncture.
4. Take out the repair patch, cut it into required shape and size, which should be larger than the puncture area, place the patch over the puncture area and press firmly.
5. You can use it again after 30 minutes.
   If the damage is bigger than 1” (2.5cm), we recommend using a Silicone or rubber based glue for repair. Please read warning statement on glue prior to use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>