LANCER WORLDWIDE CED-400 Counter Electric Dispenser User Manual

LANCER WORLDWIDE CED-400 Counter Electric Dispenser

IMPORTANT SAFETY INSTRUCTIONS

READ ALL SAFETY INSTRUCTIONS BEFORE USING THIS UNIT.
This manual contains important safety information and all applicable safety precautions must be observed. To reduce the risk of fire, electric shock, damage to the equipment or personal injury when using this unit all instuctions/warnings on the product being used must be followed:

• ! WARNING
  Text following the Warning signal indicates a hazardous situation, which if not avoided, will result in death or serious injury. Be sure to read all Warning statements before proceeding with the installation.

• ! CAUTION Text following the Caution signal indicates a hazardous situation, which if not avoided, could result in minor or moderate injury. Be sure to read the Caution statements before proceeding with the installation.

• ATTENTION
  Text following the Attention signal addresses a situation that if not followed could potentially damage the equipment. Be sure to read the Attention statements before proceeding.

• NOTE Text following the Note signal provides you with information that may help you more effectively perform the installation procedures within this manual. Disregarding information will not cause damage or injury, however it may limit the performance of the dispenser.

• Flammable Material Warning Symbol When used in manual, it is to warn against possible ignition of flammable material if proper care is not taken. In order to reduce flammability hazards, the installation and servicing of this appliance must be only carried out by a suitably qualified person. Disposal requires transfer to authorized recycler for processing to avoid damages to the environment or other hazards.

H R290 Refrigerant Warning

This system uses a flammable refrigerant under pressure. Do not tamper with it. Keep clear of obstruction all ventilation openings in the appliance enclosure. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not damage the refrigerating circuit. Contact qualified service personnel before disposal. In order to minimize the risk of possible ignition due to incorrect parts or improper service, only factory authorized personnel should perform service on the appliance and its component parts. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. Replace component parts with like components. Only use genuine Lancer parts or parts certified by Lancer.

Intended Use

The dispenser is for indoor use only. This unit is not a toy. Children should be supervised not to play with appliance. It should not be used by children or infirm persons without supervision. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be performed by children without supervision. The min/max ambient operating temperature for the dispenser is 64°F to 100°F (18°C to 38°C) at a max altitude of 16,400 ft (5,000 m). Do not operate unit outside these conditions. Should freezing occur, cease operation of the unit and contact authorized service technician. Service, cleaning, and sanitizing should be accomplished only by trained personnel. During installation, old hose-sets should not be reused to connect the unit to the water mains; new hose-sets should always be used. Applicable safety precautions must be observed. Instruction warnings on the product being used must be followed.

Electrical Warning

Check the dispenser name plate label, located behind the splash plate, for the correct electrical requirements of unit. Do not plug into a wall electrical outlet unless the current shown on the serial number plate agrees with local current available. Follow all local electrical codes when making connections. Each dispenser must have a separate electrical circuit. Do not use extension cords with this unit. Do not ‘gang’ together with other electrical devices on the same outlet. Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance. The key-switch does not disable the line voltage to the transformer primary. Always disconnect electrical power to the unit to prevent personal injury before attempting any internal maintenance. The resettable breaker switch should not be used as a substitute for unplugging the dispenser from the power source to service the unit. Only qualified personnel should service internal components of electrical control housing. Make sure that all water lines are tight and units are dry before making any electrical connections!

Carbon Dioxide (CO2)

• WARNING: Carbon Dioxide (CO2) is a colorless, noncombustible gas with a light pungent odor. High percentages of CO2 may displace oxygen in the blood.
• WARNING: Prolonged exposure to CO2 can be harmful. Personnel exposed to high concentrations of CO2 gas will experience tremors which are followed by a loss of consciousness and suffocation.
• WARNING: If a CO2 gas leak is suspected, immediately ventilate the contaminated area before attempting to repair the leak.
• WARNING: Strict attention must be observed in the prevention of CO2 gas leaks in the entire CO2 and soft drink system.

WATER NOTICE

Provide an adequate potable water supply. Water pipe connections and fixtures directly connected to a potable water supply must be sized, installed, and maintained according to federal, state, and local laws. The water supply to the carbonator must be at least a 3/8 inches (9.525 mm) pipe with a minimum of 25 psi (0.172 MPa) line pressure, but not exceeding a maximum of 50 psi (0.345 MPa). Water pressure exceeding 50 psi (0.345 MPa) must be reduced to 50 psi (0.345 MPa) with pressure regulator. The water supply to non-carb drinks must be a minimum of 55 psi (0.379 MPa), using a water booster if needed. Use a filter in the water line to avoid equipment damage and beverage off-taste. Check the water filter periodically, as required by local conditions. The water supply must be protected by means of an air gap, a backflow prevention device or another approved method to comply with NSF standards. A leaking inlet water check valve will allow carbonated water to flow back through the pump when it is shut off and contaminate the water supply. Ensure the backflow prevention device complies with ASSE and local standards. It is the responsibility of the installer to ensure compliance.

SPECIFICATIONS AND FEATURES

1. DIMENSIONS
2. Width: 10.83 inches (275 mm)
3. Depth: 23.00 inches (584 mm)
4. Height: 30.13 inches (765 mm)
5. WEIGHT
6. Shipping: 154 lbs (69.9 kg)
7. Empty: 121 lbs (54.9 kg)
8. Operating: 171 lbs (77.6 kg) Ice
9. Bath: 50 lbs (22.7 kg)
10. ELECTRICAL
11. 115 VAC, 60 Hz, 12.0
12. Amps 220-240 VAC, 50 Hz, 6.0
13. Amps 220-240 VAC, 60 Hz, 6.0 Amps
14. CARBON DIOXIDE (CO2) SUPPLY
15. Min Pressure: 70 psi (0.483 MPa)
16. Max Pressure: 80 psi (0.552 MPa)
17. FITTINGS
18. Water for Carb Inlet: 3/8 inch barb Plain
19. Water Inlet: 3/8 inch barb Brand
20. Syrup Inlets: 1/4 inch barb CO2 Inlet: 1/4 inch barb
21. WATER SUPPLY TO CARBONATOR
22. Min Flowing Pressure: 25 psi (0.172 MPa)
23. Max Flowing Pressure: 50 psi (0.345 MPa)
24. WATER SUPPLY TO NON-CARB DRINKS
25. Min Flowing Pressure: 55 psi (0.379 MPa)
26. Max Flowing Pressure: 120 psi (0.827 MPa)

This unit emits a sound pressure level below 70 dB
Max Altitude: 16,400 ft (5,000 m)
Climatic Class Definitions

• SN (Subnormal) suitable for use under ambient temperature range of 50 °F ~ 90 °F N (Normal) suitable for use under an ambient temperature range of 61 °F ~ 90 °F
• ST (Subtropical) suitable for use under ambient temperature range of 64 °F ~ 100 °F T (Tropical) suitable for use under an ambient temperature range of 64 °F ~ 109 °F

General System Overview – Remote Syrup Pumps

PRE-INSTALLATION CHECKLIST

1. TOOLS REQUIRED

2. Oetiker Pliers

3. Tubing Cutters

4. Wrench

5. Slotted Screwdriver

6. Phillips Screwdriver

7. Drill

8. BIB SYSTEM

9. BIB Rack

10. BIB Syrup Boxes

11. BIB Regulator Set

12. BIB Connectors

13. POST MIX ACCESSORIES

14. High Pressure CO2 Regulator

15. Low-Pressure CO2 Regulator Manifold

16. CO2 Supply

17. Chain for CO2 Tank

18. Beverage Dispenser Beverage Tubing

19. Oetiker Clamp Fittings

20. Water Booster (Lancer PN: 82-3401 or MC-163172

21. Water Regulator

22. CONSIDER THE FOLLOWING BEFORE INSTALLATION

23. Location of Water Supply Lines

24. Location of Drain

25. Location of Electrical Outlet

26. Location of Heating and Air Conditioning Ducts

27. Do you have enough space to install the dispenser?
    Is countertop level?

28. Can the countertop support the weight of the dispenser? (Include the weight of an ice machine plus weight of ice,  if necessary)

29. Is dispenser located away from direct sunlight or overhead lighting?

Read This Manual
This manual was developed by Lancer Worldwide as a reference guide for the owner/operator and installer of this dispenser. Please read this manual before installation and operation of this dispenser. Please see pages 18-20 for troubleshooting or service assistance. If the service cannot be corrected please call your Service Agent or Lancer Customer Service. Always have your model and serial number available when you call.

INSTALLATION

Unpacking the Dispenser

1. Cut package banding straps and remove.
2. Open the box and remove the parts tray.
3. Close the lid, then remove using the handle cutouts.
4. Remove accessory kit and loose parts.

NOTE
Inspect unit for concealed damage. If evident, notify delivering carrier and file a claim against the same.
! WARNING

Never energize the machine if there is any trace of damage. Contact Lancer Customer Service for assistance.

Remove plywood shipping base from unit by moving unit so that one side is off the countertop or table allowing access to screws on the bottom of the plywood shipping base

NOTE
If the unit is to be transported, it is advisable to leave the unit secured to the plywood shipping base.
If a leg kit has been provided, assemble legs by tilting unit.
! ATTENTION

DO NOT LAY UNIT ON ITS SIDE OR BACK

Selecting/Preparing a Counter Location

NOTE

The dispenser should only be installed in a location where it can be overseen by trained personnel.

WARNING

When positioning the appliance, ensure the supply cord is not trapped or damaged.

1. Select a location that is in close proximity to a properly grounded electrical outlet, within five (5) feet (1.5 m) of a drain, and a water supply that meets the requirements shown in the Specifications section found on page 5.
2. Select a location for the syrup pumps, CO2 tank, syrup containers, and water filter (recommended).
3. Condenser air is drawn in from the top front and vents located on the bonnet and discharged out the rear top of the bonnet. A minimum of eight (8) inches (203 mm) of clearance must be maintained over the top of the unit to provide for proper airflow and circulation.
4. Cut the necessary holes in the countertop for mounting inthe designated dispenser location.

WARNING

Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction. Failure to maintain specified clearance will cause the compressor to overheat and will result in compressor failure.

Leveling the Dispenser

In order to facilitate proper dispenser drainage, ensure that the dispenser is level, front to back and side to side. Place a level on the top of the rear edge of the dispenser. The bubble must settle between the level lines. Repeat this procedure for the remaining three sides. Adjust as necessary. For optimum performance place the unit at a 0° tilt. The maximum tilt is 5°.

Dispenser Installation

NOTE

The installation or relocation must be carried out by qualified personnel with up-to-date knowledge and practical experience in accordance with current regulations.

1. The dispenser is designed to be installed either permanently to a counter or placed on a counter using the legs (included in the Lancer kit, PN 82-1704).
   NOTE
   NSF-listed units must be sealed to the counter or use the legs provided.

2.  When the dispenser is to be permanently bolted to the countertop, the dispenser base must be sealed to the countertop with a bead of silicone caulk or sealant which provides a smooth and easily cleanable bond to the counter.

3. Once the dispenser is installed to the counter or placed on the counter using legs provided, remove the cup rest and splash plate.

4. Remove the merchandiser by removing the two (2) top screws and two (2) bottom screws.

5. Remove the bonnet by removing the two (2) front screws.

6. Route power cord up the front of the unit for connection.

7. Connect drain tube to the drain fitting located on the bottom of the drip tray and secure drain tube with clamp.

8. Route the drain line to designated floor drain.

9. Route appropriate tubing from the syrup pump location to the syrup inlets located behind the splash plate. Connect tubing to inlets using the Oetiker pliers and clamps. Repeat for all syrup connections.

10. Connect plain water tubing to water pump.

11. Route appropriate tubing from the water source to the carbonator pump inlet at the unit. Route up the left side of the unit to ensure space for the keyswitch.

12. Connect the tubing to the water source using Oetiker pliers and clamps.
    ! ATTENTION – critical for performance Carefully read this before filling the water bath tank. In order to optimize the maximum performance of the dispenser, the following MUST be adhered to:

13. Fill a large bucket with approx. 5.4 gallons (20.4 L) of distilled water.
    ! ATTENTION For proper function of the electronic ice bank control the total dissolved solids (TDS) measurements should be 100-500 ppm.

14. Add 1/8 oz (4 g) of baking soda to distilled water and stir.

15. Remove yellow cap from fill hole and insert a funnel into the fill hole.

16. Carefully pour the distilled water mixture into the water bath tank until water flows out of the overflow tube at the front of the unit. Then replace yellow cap.
    ! ATTENTION The water bath compartment must be filled with water before connecting the unit, otherwise the compressor fan may not operate properly. DO NOT use Reverse Osmosis (RO) or purified water.

17. Using tubing cutters, cut water supply line and install “U” fitting, (PN 01-2128/01).

18. Route appropriate tubing from the plain water inlet, located  at the front of the unit, to one side of the “U” fitting at water supply and connect tubing to inlet.

19. Route appropriate tubing from the carbonator pump inlet to the open “U” fitting at water supply then connect tubing to carb water inlet using a flare seal washer (PN 05-0017). Use a back-up wrench to prevent damage to carbonator pump. notE If the water source is above 50 psi (0.345 MPa), cut tubing assembly and install Water Regulator Kit (PN 18-0253/02, sold separately) as shown in kit instruction sheet. Once installed, use a test gauge assembly (PN 22-0138, sold separately), to set regulator at a maximum of 50 psi (0.345 MPa).

20. Route appropriate tubing from the CO2 supply to the CO2 inlet and connect tubing to it.

21. Feed all tubing, power cord, and drain line through the back of the unit. If using 3/8” tubing, place reduction point behind unit.

22. Turn on water supply and check for leaks.

23. Plug in the unit to a grounded electrical outlet to power on and begin building an ice bank.
    ! WARNING Never energize the machine if there is any trace of damage. Contact Lancer Customer Service for assistance. The dispenser must be properly electrically grounded to avoid serious injury or fatal electrical shock. The power cord has a three-prong grounded plug. If a three-hole grounded electrical outlet is not available, use an approved method to ground the unit. Follow all local electrical codes when making connections. Each dispenser must have a separate electrical circuit. Do not use extension cords. Do not connect multiple electrical devices on the same outlet

Installing Remote Syrup Pumps – Bag In Box

1. Install BIB rack and remote pumps according to manufacturers’ instructions.

2. Once pumps and BIB rack are installed, measure and cut tubing to length between the pump CO2 inlets, then connect tubing to all pumps.

3. Using tubing cutters, cut the CO2 supply line to the syrup pumps and install tee fitting. Then, route the appropriate tubing from the tee fitting to the syrup pumps and to the unit.

4. Connect tubing from the dispenser syrup inlet to the syrup pump outlet fitting. Repeat for each syrup line/pump.

5. Install BIB (bag in box) connectors onto the syrup pump inlet tubing.
   ! ATTENTION
   Use proper connector for syrup manufacturer.

6. Connect syrup BIBs to connectors. Repeat for each syrup line/pump.

Installing CO2 Supply

1. Connect high pressure CO2 regulator assembly to CO2 cylinder or bulk system.
   ! ATTENTION
   Before installing regulator, ensure that a seal (washer or O-ring) is present in regulator attachment nut.

2. Connect a 1/4” nut, 3/8” stem and seal to CO2 regulator outlet.

3. Route appropriate tubing from the low pressure CO2 regulator manifold location to the 1/4” nut, 3/8” stem on the high pressure CO2 regulator attached to source and connect tubing ATTENTION A dedicated CO2 regulator is required to supply the CO2 inlet at the unit as well as to all remote syrup pumps.

4. Connect tubing routed from the CO2 inlet at the unit to one of the low pressure CO2 regulator manifold outlets.

5. Connect tubing routed from the syrup pump location to the second outlet of the low pressure CO2 regulator manifold.

6. Using a wrench, loosen lock nut on the regulator adjustment screw of the high pressure CO2 regulator connected to the source, then using a screwdriver back out lock nut screw all the way.
   ! WARNING DO NOT TURN ON CO2 SUPPLY AT THIS TIME.

7. Repeat Step 6 for both low pressure CO2 regulators on the regulator manifold routed to the unit and the syrup pumps.

Dispenser Setup

1. Purge water to fill carbonator tank by opening carbonator relief valve. Close relief valve once water comes out.

2. Activate each valve until a steady flow of water is achieved.

3. Turn the power off.

4. Unplug the Pump Motor Connector from the control box. Use the wiring diagram either on the unit control box or in the back of this manual for reference.
   ! ATTENTION Failure to disconnect the motor power supply will damage the carbonator motor, the pump and void the warranty.

5. Turn the power on.

6. Turn on CO2 at the source. Using a screwdriver, adjust the high pressure regulator at the source to 110 psi (0.758 MPa), then tighten locknut with wrench.

7. Adjust both of the low pressure regulators on the regulator manifold to 75 psi (0.517 MPa) then tighten locknut with wrench.

8. Turn syrup off at back block.

9. Activate each valve until gas-out is achieved.

10. Turn power off.

11.  Plug the Pump Motor Connector back into the control box.

12.  Turn power on.
    NOTE
    Pump Motor will run for a few seconds to fill carbonator tank.

13. Activate each valve until the carbonator pump comes on. Release the button, allow carbonator to fill and stop. Repeat this process until a steady flow of carbonated water is achieved.

Adjust Water Flow Rate & Syrup/Water Ratio

NOTE

Do not set flow rates or dispense from the unit until a complete ice bank is established.

1. Using a Lancer brix cup verify water flow rate (5 oz. in 4 sec.). Use a screwdriver to adjust if needed.
2. Remove nozzle by twisting counterclockwise and pulling down, then remove diffuser by pulling down.
3. Install Lancer (yellow) syrup separator (PN 54-0031) in place of nozzle.
4. Reopen syrup shut-off at mounting block.
5. Activate valve to purge syrup until steady flow is achieved.
6. Using a Lancer brix cup, activate the valve and capture a sample. Verify that the syrup level is even with the water level. Use a screwdriver to adjust if needed.
7.  Repeat process for each valve.
8. Reinstall the merchandiser, splash plate, cup rest, and drip tray then reattach bonnet using the top bonnet screw.

Volumetric Valve Adjustment

1. Remove the ID panel from the front of the first valve.

2. Insert the programmer’s 10-pin connector into the ID panel plug located on the front of the circuit board.

3. When properly connected, the programmer will run a
   self-diagnostic test. The display will show all “8’s” with the decimal points lighted. After about three (3) seconds, the display indicates the setting of the dip switches.
   NOTE
   If the programmer does not run its diagnostic test properly, disconnect it and try plugging it in again. If the programmer still fails, replace the programmer.

4.  After the programmer is connected, press the “Read Mem” button.

5. Press the “Ratio +” or the “Ratio -” key until the desired ratio is displayed.

6. Verify the drink type by pressing “Carb Toggle” to select “C” for carbonated or “n” for non-carbonated.

7. Press the “Enter” button to program the valve with the setting on the display.

8. Verify ratio by pressing “Read Mem”.

9. Disconnect the programmer and repeat steps 4-9 for each valve.

CLEANING AND SANITIZING

General Information

Lancer equipment is shipped from the factory after being cleaned and sanitized in accordance with the National Sanitation Foundation (NSF) guidelines. The operator of the equipment must provide continuous maintenance
as required by this manual and/or state and local health department guidelines to ensure proper operation and sanitation requirements are maintained.
The cleaning procedures provided herein pertain to the Lancer equipment identified by this manual. If other equipment is being cleaned, follow the guidelines established by the manufacturer for that equipment.
Cleaning should be accomplished only by trained personnel. Sanitary gloves are to be used during cleaning operations. Applicable safety precautions must be observed. Instruction warnings on the product being used must be followed.

ATTENTION

• Use sanitary gloves when cleaning the unit and observe all applicable safety precautions.
• DO NOT use a waterjet to clean or sanitize the unit.
• DO NOT disconnect water lines when cleaning and sanitizing syrup lines to avoid contamination.
• DO NOT use strong bleaches or detergents; these can discolor and corrode various materials.
• DO NOT use metal scrapers, sharp objects, steel wool, scouring pads, abrasives, or solvents on the dispenser.
• DO NOT use hot water above 140° F (60° C). This can damage the dispenser.
• DO NOT spill sanitizing solution on any circuit boards. Ensure all sanitizing solution is removed from the system.
• DO NOT use mechanical devices or other means to accelerate the defrosting process; other than those recommended by the manufacturer.

Cleaning and Sanitizing Solutions

Cleaning Solution
Mix a mild, non-abrasive detergent (e.g. Sodium Laureth Sulfate, dish soap) with clean, potable water at a temperature of 90°F to 110°F (32°C to 43°C). The mixture ratio is one ounce of cleaner to two gallons of water. Prepare a minimum of five gallons of cleaning solution. Do not use abrasive cleaners or solvents because they can cause permanent damage to the unit. Ensure rinsing is thorough using clean, potable water at a temperature of 90°F to 110°F. Extended lengths of product lines may require additional cleaning solution.
Other Supplies Needed

• Clean cloth towels
• Bucket
• Extra nozzle
• Sanitary gloves
• Small brush (PN 22-0017)

Sanitizing Solution
Prepare the sanitizing solution in accordance with the manufacturer’s written recommendations and safety guidelines. The type and concentration of sanitizing agent recommended in the instructions by the manufacturer shall comply with 40 CFR §180.940. The solution must provide 200 parts per million (PPM) chlorine (e.g. Sodium Hypochlorite or bleach) and a minimum of five gallons of sanitizing solution should be prepared.

Daily Cleaning

1. Using the cleaning solution, clean top cover and all exterior stainless steel surfaces.
2. Clean exterior of dispensing valves and ice chute.
3. Remove cup rest then clean the drip tray and cup rest. Replace cup rest and drip tray when finished.
4. Wipe clean all splash areas using a damp cloth soaked in cleaning solution.
5. Clean beverage valves as specified by the section “Cleaning and Sanitizing Nozzles” on page 17.

Scheduled Maintenance & Cleaning

As Needed| •     Keep exterior surfaces of dispenser clean (include drip tray and cup rest) using a clean, damp cloth.
---|---

Daily

| •        Remove each nozzle and diffuser and rinse well in warm water. DO NOT use soap or detergent. This will cause foaming and off taste in finished product.

•        Remove cup rest and wash in warm soapy water.

•        Pour warm soapy water into the drip tray and wipe with a clean cloth.

•        With a clean cloth and warm water, wipe off all of the unit’s exterior surfaces. DO NOT USE ABRASIVE SOAPS OR STRONG DETERGENTS.

•        Reinstall the cup rest, diffusers, and valve nozzles.

Weekly

| •        Taste each product for off tastes.

•        Remove the unit’s bonnet and check the level of water in the water bath. Replenish as required and reinstall bonnet.

Monthly

| •     Unplug the dispenser from the power source.

•     Remove the bonnet and clean the dirt from the condenser air filter using a soft brush.

•     Reinstall the bonnet and plug in the unit.

Every Six Months

|

•     Clean and sanitize the unit using the appropriate procedures outlined in the Cleaning and Sanitizing section of this manual.

Yearly

|

•        Clean the water bath interior, including evaporator coils and refrigeration components.

•        Clean the entire exterior of the unit.

Cleaning and Sanitizing Nozzles

1. Disconnect power, so as to not activate valve while cleaning.
2. Remove nozzle by twisting counterclockwise and pulling down.
3. Remove diffuser by pulling down.
4. Rinse nozzle and diffuser with warm water.
5. Wash nozzle and diffuser with cleaning solution then immerse in sanitizing solution and let sit for fifteen (15) minutes.
6. Set nozzle and diffuser aside and let air dry. DO NOT rinse with water after sanitizing.
7. Reconnect diffuser and nozzle.
8. connect power.
9. Taste the drink to verify that there is no off-taste. If off-taste is found, flush syrup system again.

! CAUTION

Following sanitization, rinse with end-use product until there is no aftertaste. Do not use a fresh water rinse. This is an NSF requirement. Residual sanitizing solution left in the system creates a health hazard.

Cleaning and Sanitizing Syrup Lines – Bag in Box

1. Disconnect syrup lines from BIB’s.
2. Place syrup lines, with BIB connectors and any adapters, in a bucket of warm water.
3. Activate each valve to fill the lines with warm water and flush out syrup remaining in the lines.
4. Prepare cleaning solution as described in the Cleaning and Sanitizing Solutions section.
5. Place syrup lines, with BIB connectors and any adapters, into cleaning solution.
6. Activate each valve until lines are filled with cleaning solution then let stand for ten (10) minutes.
7. Flush out cleaning solution from the syrup lines using clean, warm water.
8. Prepare sanitizing solution as described in the Cleaning and Sanitizing Solutions section.
9. Place syrup lines into sanitizing solution and activate each valve to fill lines with sanitizer. Let sit for ten (10) minutes.
10. Reconnect syrup lines to BIB’s and draw drinks to flush solution from the dispenser.
11. Taste the drink to verify that there is no off-taste. If off-taste is found, flush syrup system again.

! CAUTION

Following sanitization, rinse with end-use product until there is no aftertaste. Do not use a fresh water rinse. This is an NSF requirement. Residual sanitizing solution left in the system creates a health hazard.

TROUBLESHOOTING

valve bodies.

2.     Worn or damaged paddle arm assemblies.

3.     Cracked valve bodies.

| 1.     Tighten all six (6) retaining screws.

2.     Replace paddle arm assemblies.

3.     Replace valve body.

Miscellaneous leakage.| 1.     Gap between parts.

2.     Damaged or improperly installed O-rings.

| 1.     Tighten appropriate retaining screws.

2.     Replace or adjust appropriate O-rings

Insufficient water flow.| 1.     Insufficient incoming supply water pressure.

2.     Shutoff on mounting block not fully open.

3.     Foreign debris in water flow control.

4.     Foreign debris in water pump strainer.

| 1.        Verify incoming water supply pressure to plain and carb inlet is a minimum of 25 psi (0.172 MPa) and 55 psi (0.379 MPa) respectively.

2.        Open shutoff fully.

3.        Remove water flow control from upper body and clean out any foreign material to ensure smooth-free spool movement.

4.          Remove water pump strainer and clean.

Insufficient syrup flow.| 1.     Insufficient CO2 pressure to BIB pumps.

2.     Out of CO2 .

3.     Shutoff on mounting block not fully open.

4.     Foreign debris in syrup flow control.

5.     Bad syrup pump.

| 1.        Adjust CO2 pressure to 75 psi (0.517 MPa) [minimum 70 psi (0.480 MPa)] for BIB pumps.

2.        Replace CO2 tank/refill.

3.        Open shutoff fully.

4.        Remove syrup flow control form upper body and clean out any foreign material to ensure smooth-free spool movement.

5.        Replace BIB pump.

Erratic ratio.| 1.     Incoming water and/or syrup supply not at minimum flowing pressure.

2.     Foreign debris in water and/or syrup flow controls.

| 1.     Check pressure and adjust.

2.     Remove flow controls from upper body and clean out any foreign material to ensure smooth-free spool movement.

No product dispensed.| 1.     Water and syrup shutoffs on mounting block not fully open.

2.     Cup lever arm or ID panel actuator on electric valve is not actuating the switch.

3.     Electric current not reaching valve.

4.     Improper or inadequate water or syrup supply.

5.     Bad valve solenoid(s).

| 1.        Open shutoff fully.

2.        Replace the lever, the ID panel actuator or the switch as needed.

3.        Check electric current supplied to valve. If current is adequate, check solenoid coil and switch. Replace if necessary.

4.        Remove valve from mounting block and open shutoffs slightly. Check water and syrup flow. If no flow, check dispenser for freeze-up or other problems.

5.        Replace solenoid(s).

Water or syrup shutoff on mounting block not fully open.

2.     Improper or inadequate water or syrup flow.

3.     CO2 pressure too low.

4.     Stalled or inoperative BIB pump.

5.     Kinked line.

| 1.        Open shutoff fully.

2.        Remove valve from mounting block, open shutoffs slightly and check water and syrup flow. If no flow, check dispenser for freeze-up or other problems. Ensure BIB connection is engaged.

3.        Check the CO2 pressure to the BIB pumps to ensure it is between 70 and 80 psi (0.483 and

0.552 MPa).

4.     Check CO2 pressure and/or replace pump.

5.     Remove kink or replace line.

Valve will not shut off.| 1.     Cup lever may be sticking or binding.

2.     Switch not actuating freely.

3.     Solenoid armature not returning to bottom position.

| 1.        Correct or replace lever.

2.        Check switch for free actuation.

3.        Replace defective armature or spring.

Excessive foaming.| Incoming water or syrup temperature too high.

2.     CO2 pressure too high.

3.     Water flow rate too high.

4.     Nozzle and diffuser not installed.

5.     Nozzle and diffuser not clean.

6.     Air in BIB lines.

7.     Poor quality ice.

8.     High beverage temperature.

| 1.        Correct prior to dispenser. Consider larger dispenser or pre- cooler.

2.        Adjust CO2 pressure downward, but not less than 70 psi.

3.        Readjust and reset ratio. Refer to “Adjust Water Flow Rate & Syrup/Water Ratio” Section.

4.        Remove and reinstall properly.

5.        Remove and clean.

6.        Bleed air from BIB lines.

7.        Check quality of ice used in drink.

8.        Check refrigeration system.

Water continually overflows from water bath into drip tray.| 1.        Loose water connection(s).

2.        Flare seal washer leaks.

3.        Faulty water coil.

| 1.     Tighten water connections.

2.     Replace flare seal washer.

3.     Replace water coil.

Warm drinks.| 1.     Dispenser was recently installed.

2.     Restricted airflow.

3.     Dispenser connected to hot water supply.

4.     Condenser fan motor not working.

5.     Dirty condenser, air vents clogged.

6.     Dispenser capacity exceeded.

| 1.     It may take up to 5 hours after install to reach the desired temperature.

2.     Check clearances around sides, top, and inlet of unit. Remove objects blocking airflow through grill.

3.     Switch to cold water supply.

4.     Replace condenser fan motor.

5.     Clean condenser and air vents of any blockage.

6.     Add pre-cooler or replace with larger dispenser.

Unit will not start.| 1.        Compressor startup delay.

2.        Motor timed out.

| 1.     When starting unit or if current is interrupted, there is a 5 minute delay before the compressor/fan starts.

2.     There is a 3 minute protection timer on the carbonator level sensor. If the motor has timed out, check water supply and reset by momentarily disconnecting power.

1.                  Out of CO2, CO2 not turned on, or low CO2 pressure.

2.                  Out of syrup.

3.                  BIB connector not tight.

4.                  Kinks in syrup or gas lines.

| ****

1.                    Replace CO2 supply, turn on CO2 supply, or adjust CO2 pressure to 70-80 PSI (0.483-0.552 MPA).

2.                    Replace syrup supply.

3.                    Fasten connector tightly.

4.                    Straighten or replace lines.

BIB pump operating, but no flow.| 1.                  Leak in syrup inlet or outlet line.

2.                  Defective BIB pump.

| 1.                  Replace line.

2.                  Replace BIB pump.

BIB pump continues to operate when bag is empty.| 1.                  Leak in suction line.

2.                  Leaking O-ring on pump inlet fitting.

3.                  Defective syrup BIB pump.

| 1.                  Check BIB connector, if still leaking then replace line.

2.                  Replace O-ring

3.                  Replace defective pump.

BIB pump fails to restart after bag replacement.| 1.                  BIB connector not on tightly.

2.                  BIB connector is stopped up.

3.                  Kinks in syrup line.

| 1.                  Tighten BIB connector.

2.                  Clean out or replace BIB connector.

3.                  Straighten or replace line.

BIB pump fails to stop when dispensing valve is closed.| 1. Leak in discharge line or fittings.

2.                  Empty BIB.

3.                  Air leak on inlet line or bag connector.

| 1.                  Repair or replace discharge line.

2.                  Replace BIB.

3.                  Repair or replace.

Low or no carbonation.| 1.                  Low or no CO2.

2.                  Low water pressure.

3.                  Worn or defective carbonator pump.

4.                  Backflow preventer not allowing water to flow.

5.                  Probe malfunctioning.

6.                  PCB malfunctioning.

| ****

1.                    Check CO2 supply. Adjust CO2 pressure to 70 PSI (0.483 MPA).

2.                    Need water booster kit.

3.                    Replace carbonator pump.

4.                    Replace backflow preventer, noting the flow direction arrow from pump to coldplate.

5.                    Replace probe.

6.                    Replace PCB.

Dispenser Disposal

The unit’s R290 refrigerant and foam materials are combustible materials and discarded units should be isolated from fire sources and cannot be burned. To prevent possible harm to the environment from improper disposal, recycle the unit by locating an authorized recycler or contact the retailer where the product was purchased. Comply with local regulations regarding disposal of the refrigerant and insulation.

ILLUSTRATIONS AND PART LISTINGS

Main Unit Assembly, CED 400

Item        Part No.                      Description

Refrigeration Deck Assembly, CED 400

Item      Part No.          Description

Wiring Diagram

Plumbing Diagram

6655 Lancer Boulevard San Antonio, TX 78219 lancerworldwide.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>