AEOTEC ZW090PLUS-C Z-Stick Gen5+ USB Stick and Antenna User Guide
- June 5, 2024
- Aeotec
Table of Contents
Z-Stick Gen5+ user guide: Aeotec Help Desk
Z-Stick Gen5+ user guide
Modified on: Tue, 29 Dec 2020 at 12:54 AM
Z-Stick Gen5+ (https://aeotec.com/z-wave-usb-stick/) offers compatibility
with newer technologies than non +/plus, standard Z-Stick Gen5. This includes
Raspberry Pi 4 compatibility and native Z-Wave SmartStart
(https://aeotec.com/z-wave-home-automation/z-wave-smart-start.html) and
Z-Wave S2 (https://aeotec.com/z-wave-s2/) compatibilities.
The technical specifications of Z-Stick Gen5+
(https://aeotec.freshdesk.com/a/solutions/articles/6000242203) can be viewed
at that link.
Get to know your Z-Stick
‘C’ LED Indications
LED Color | Unplugged / Plugged | Description of function |
---|---|---|
No LED | Unplugged | No activity, z-wave management mode |
Slow Blue blink | Unplugged | Pair/inclusion mode activate |
Fast Amber blink | Unplugged | Unpair/exclusion mode active |
Red blinking LED | Unplugged, RESET button held | Indicates that it has entered |
factory reset mode. Will only reset if
The RESET button is held for a full 20 seconds (followed by the confirmation
LED indicator).
Factory reset does not happen if released earlier than 20 seconds.
Solid blue for 2 seconds| Unplugged| Confirmation of success/communication for
pair, unpair, or factory reset.
Solid Amber
Solid Green| Plugged into USB| Normal activity
Amber LED = Charging the battery
Green LED = Fully charged
Blue Flash| Plugged into USB| Indicates that Z-Stick Gen5 has communicated a
Z-Wave command.
Z-Stick Gen5+ compared to Z-Stick Gen5
There are subtle differences between Z-Stick Gen5+ and Z-Stick Gen5, you can
learn more by reading the table
at this page: https://aeotec.com/z-wave-home-automation/development-kit-
pcb.html
(https://aeotec.com/z-wave-home-automation/development-kit-pcb.html)
Important safety information
Please read this and other device guides carefully. Failure to follow the
recommendations set forth by Aeotec Limited may be dangerous or cause a
violation of the law. The manufacturer, importer, distributor, and/or reseller
will not be held responsible for any loss or damage resulting from not
following any instructions in this guide or in other materials.
Keep product and batteries away from open flames and extreme heat. Avoid direct
sunlight or heat exposure.
Improper battery use may damage the product.
Z-Stick Gen5 is intended for indoor use in dry locations only. Do not use in
damp, moist, and/or wet locations.
Quick start
Z-Stick operates in 2 different modes: Network management, Serial connection. Network management is enabled when the Z-Stick Gen5+ is unplugged from USB. Serial connection allows you to interface the Z-Stick Gen5+ to any third-party software allowing virtual connection via COM ports or CDC ACM connection.
To quickly get started, please follow our Z-Stick Gen5 Quick Start – Just the
essentials article.
(https://aeotec.freshdesk.com/solution/articles/6000092802-z-stick-gen5
-quick-start-just-the-essentials)
We will go over the different potential functions of the Z-Stick Gen5 below.
Manually pair/include Z-Wave devices
Video
How to connect a Z-Wave device to Aeotec Z-Stick Gen5+
Steps
-
Unplug the Z-Stick Gen5 from any USB connection, this will enable Network management mode.
-
Tap the button once on Z-Stick Gen5+. Its LED will blink blue slowly to indicate it is in pair mode.
-
Follow the instruction of the Z-Wave device that you want to pair. Typically the button press on the Z-Wave device is a single tap, but some have special button presses (ie. hold for 2 seconds and release, triple tap, double-tap, etc).
Z-Stick Gen5+ LED will confirm if it paired something successfully by showing a solid blue LED for 2 seconds before returning to a slow blinking blue LED. -
Repeat step 3 for any device you want to pair if you have multiple devices that you need to include.
-
When done, tap the button once on Z-Stick Gen5+ to bring it out of pair/include mode. The LED will deactivate.
Manually unpair/exclude Z-Wave devices
Steps
-
Unplug the Z-Stick Gen5 from any USB connection, this will enable Network management mode.
-
Press and hold the button on Z-Stick Gen5+.
-
Its LED will blink an Amber color rapidly to indicate it is in unpair/exclude mode. Quickly release the button.
-
Follow the instruction of the Z-Wave device that you want to unpair. Typically the button press on the Z-Wave the device is a single tap, but some have special button presses (ie. hold for 2 seconds and release, triple tap, double-tap, etc).
Z-Stick Gen5+ LED will confirm if it paired something successfully by showing a solid blue LED for 2 seconds before returning to a fast blinking Amber color LED. -
Repeat step 3 for any device you want to unpair if you have multiple devices that you need to exclude.
-
When done, tap the button once on Z-Stick Gen5+ to bring it out of unpair/exclude mode. The LED will deactivate.
Third-party software
In order to use the Z-Stick Gen5 and control your Z-Wave network, you must
download third-party software to have full control over your software. You can
find all known third party software in this link:
https://aeotec.freshdesk.com/solution/articles/6000042049-host-software
(https://aeotec.freshdesk.com/solution/articles/6000042049-host-software)
Free recommended software
We recommend free software Domoticz if you are just getting started as it is
one of the easiest free software you can use. You can view this guide here:
Z-Stick Gen5 and how to get started with Domoticz.
(https://aeotec.freshdesk.com/solution/articles/6000199837-quick-start-z
-stick-gen5-with-domoticz)
Advanced
Backup Tool for Z-Stick Gen5+
You are able to backup the Z-Stick Gen5 using our Z-Stick Gen5 Backup Software in any case you need to restore an older save of your network, or replace a failed Z-Stick Gen5. This way you will never have to re-do your network if there are catastrophic issues.
You can download the installation setup for Backup Software here:
https://aeotec.freshdesk.com/solution/articles/6000108806-z-stick-gen5
-backup-software
(https://aeotec.freshdesk.com/solution/articles/6000108806-z-stick-gen5
-backup-software)
You can learn how to use Backup Software here to backup, and restore:
https://aeotec.freshdesk.com/solution/articles/6000167023-how-to-use-z-stick-
gen5-backupsoftware-backup-and-restore-
(https://aeotec.freshdesk.com/solution/articles/6000167023-how-to-
use-z-stickgen5-backup-software-backup-and-restore-)
This tool can also be used to transfer your old Z-Stick Gen5 network to a
Z-Stick Gen5+, you can follow the steps here:
https://aeotec.freshdesk.com/a/solutions/articles/6000242397
(https://aeotec.freshdesk.com/a/solutions/articles/6000242397)
Z-Stick Gen5+ as a secondary controller
This must be done through the host software which takes control of the Z-Stick
USB adapter while Z-Stick is in SerialAPI-Mode.
Please consult the instruction manual of the host software to add the Z-Stick
to a pre-existing Z-Wave network (i.e. “Learn”, “Sync”, “Add as Secondary
Controller”, etc.). This function can only be performed via host software.
Steps (General):
- Connect your Z-Stick Gen5 to the software of your choice.
- Enable “Learn” mode through software.
Factory reset your Z-Stick Gen5+
At some stage, you may wish to reset all of your Z-Stick’s settings to their
factory defaults and completely remove all connected Z-Wave devices.
Steps using the RESET button
-
Unplug the Z-Stick Gen5+ from your PC.
-
Press and hold the RESET Button (located on the back of the unit) for 20 seconds and then release it when no more LED activity is happening. (You can visually watch the ‘C’ LED)
The LED will blink red faster and faster over the course of 20 seconds.
At 20 seconds, the blue LED will appear -
Wait until the blue LED disappears before releasing its RESET button.
Using third-party software to factory reset
Z-Stick also can be reset to the factory defaults settings through a third-
party software (ie. Homeseer, Domoticz, Indigo, Axial, OpenHAB, Home
Assistant, Jeedom, etc).
The third-party software must take control of the Z-Stick USB adapter while
the Z-Stick is plugged into a PC USB port.
You’ll need to refer to your third-party software instructions if you are
unsure where the function is located in the software. Find the “Reset Z-Wave
controller” option in your third-party software and activate it.
Disable LED
You can disable the LED of the Z-Stick Gen5, there is only one requirement
which is the use of a Windows OS to use the Backup Tool.
Please follow the article here and follow through with the step by step
instruction set to disable the LED of your Z-Stick Gen5:
(https://aeotec.freshdesk.com/solution/articles/6000171881-how-to-disable-
led-on-z-stick-gen5-)
https://aeotec.freshdesk.com/solution/articles/6000171881-how-to-disable-led-
on-z-stick-gen5-
(https://aeotec.freshdesk.com/solution/articles/6000171881-how-to-disable-
led-on-z-stick-gen5-)
https://help.aeotec.com/support/solutions/articles/6000242202-z-stick-gen5 -user-guide
References
- Z Pi 7 – Aeotec
- Smart Home Products - Aeotec
- Loading...
- Loading...
- Host Software : Aeotec Help Desk
- Z-Stick Gen5 Quick Start - Just the Essentials : Aeotec Help Desk
- Z-Stick Gen5 Backup Software : Aeotec Help Desk
- How to use Z-Stick Gen5 backup software (Backup, and Restore). : Aeotec Help Desk
- How to use Z-Stick Gen5 backup software (Backup, and Restore). : Aeotec Help Desk
- How to use Z-Stick Gen5 backup software (Backup, and Restore). : Aeotec Help Desk
- How to disable LED on Z-Stick Gen5. : Aeotec Help Desk
- Quick start Z-Stick Gen5 with Domoticz : Aeotec Help Desk
- s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/6006115808/original/Screen%20Shot%202015-09-29%20at%203.39.41%20PM.png?1443512429
- s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/6113943364/original/rRQkFJAGawvQ-GYTpDve7R-mMKqnZLWvKg.png?1600929872