Frakin Digital Measuring Kitchen Spoon User Manual

Digital Measuring Kitchen Spoon
User Manual

Operation requirement

When use this product to weigh goods, please handle them gently. Don’t hit it. It can be used by hand or put on flat ground to weigh doods. Stay in a stationary state when weighing, do not shake the scale in case of affecting the weighing.
Operating Instruction

1. Press the [TARE] button or [ ] button to start up, “0.0” will be shown on the display
2. If the unit on display is incorrect, you can press the [MODE] button or [ ]button to switch units.
3. Keep it a horizontal level after starting up, do not shake the scale until “0.0” is shown on the display
4. Put goods in a spoon, hold on for a few seconds, and the accurate weight data will be locked automatically.
   Note: If do not need an auto-locking function, please relieve the auto- locking function refer to the instruction (Data locking & reading).

Units

Attention:

1. Do not weigh goods that are more than max loading, overloading will damage to the product.
2. Do not use this product in windy and radioactive conditions, gentle breeze and intense radiation will cause the data on display is not steady.
3. Put this product in a clean and air-drying place, it will cause damage to the sensor and circuit board in a wet and corrosive environment.
4. If can not start up successfully, please check if the batteries work or if the battery mount is correct.

Procedure Handhold procedure

1. Keep in a horizontal level after starting up, do not shake the scale until “0.0” is shown on display. Put goods in a spoon, hold on for a few seconds, and the accurate weight data will be locked automatically.
2. Keep at a horizontal level after starting up, do not shake the scale until “0.0” is shown on display. Use a spoon to scoop up goods, and hold the spoon scale horizontally. Do not shake the scale, hold on for a few seconds, and the accurate weight data will be locked automatically.
   Notice: Keep in a tare horizontal state after starting up,:.that, horizontally when reading data.(The change in value when using spoon to scoop up goods does not affect the weighing accuracy)

Weighing on horizontal table procedure

Put on the horizontal table before starting up, then use a hand or anything with weight to press above the scale. The spoon part should be out of the table, hanging in the air motionlessly. Do not shake the scale, then startup. Put goods in a spoon, hold on for a few seconds, and the accurate weight data will be locked automatically.

Key Function Specification

Note: The ON/OFF button is the same button as TARE/ZERO button. Under the state of power-on, press the [TARE] button to switch to TARE/ZERO function.
ON/OFF
Power-on: Press the [TARE] button to start up.
Power-off: Long press [TARE] button to power off.
ZERO/TARE
Press the [TARE] button Or [ ] button after starting up, remove the weight of the vessel, then data “0.0” will be shown on the display. Then you can put goods in a spoon to weigh the weight.
Data locking & reading

1. The data is stable on the display when you weigh goods, the data will be locked automatically.
2. The data will be unlocked after pressing the [HOLD] button or [ ]button. Then weigh the goods again, and the data will be also locked automatically after the data is stable.
3. Long press the [HOLD] button or [ ] button, the data will not be locked automatically when the letters “H-ON” are shown on display.
4. Long press the [HOLD] button or [ ] button again, return to the status of automatically data locking when the letters “H-OFF” are shown on display.

Off time
The default shutdown time of this product is one minute. The – _ironic scale will extend shutdown time automatically when works continuously for one minute. Time default shutdown time of this product is one minute. The – _ironic scale will extend shutdown time automatically when works continuously for one minute.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>