IDMIX D6 Power Light User Manual
- June 5, 2024
- IDMIX
Table of Contents
D6
Power Light User Manual
Technique specification
Model No: D6
Color: Green / White / Pink
THE LIGHT PART
| Micro USB input | 5V1A |
|---|---|
| Wireless Charging input | 5W |
| Capacity | 1200mAh/3.7V/4.44WH |
| LED funtion | 1W(Max) |
| Size | 72*170.5mm |
THE BASE PART
| Micro USB input | 5V2A;9V2A |
|---|---|
| Wireless Charging output | 5W/7.5W/10W |
| Size | 73.3*11mm |
Introduction
User guide
-
Turn on and off lights
Turn the lamp button to the right, then you hear the crisp sound, that is on, turn on the light; In the state of light, turn the button to the left, reset button, that is to turn off the light. -
Adjust the brightness
In the light state, continue to turn the button to the right, you can adjust the brightness -
Change color
Just touch the color-changing area to change the color of white, green, red, blue, purple and other colors.
Charging
-
Charge the lamp:
( 1 ) Support Micro USB input charging. The standard USB charging cable can be used to charge the lamp body. Tips: When the charging indicator is red, it means that D6 enters the low power mode. Please charge D6 in time.
When the charging indicator is always on in green, it means that the battery is fully charged. -
Support wireless charging, the wireless charging base supports 5W wireless charging for the lamp body
Tips: When using the wireless charging base to charge the lamp itself or other external devices, please use the front of the wireless charging base to contact the charged device, otherwise, it will not be able to charge.
2. Charge the wireless charging base :
Support Micro USB input.
2. Charging phones through wireless:
The Wireless charging base supports wireless charging of mobile phones and
other devices and supports 10W/ 7.5w /5W third-gear power.
Tips
- The light source of this lamp cannot be replaced; when the light source reaches its end of life, the lamp shall be replaced;
- The lamp shall not be used on the plane with an inclination greater than 6 ° •,
Hazardous and risk substances
| par name | Hazardous and risk substances |
|---|---|
| Lead ( Pb ) | Mercury ( Hg ) |
| ( Cre+ ) | Polybrominated |
| biphenyls) (PBB) | PBDES |
( PBDE )
Main part| 0| 0| 0| 0| 0| 0
Accessories| 0| 0| 0| 0| 0| 0
0: At least one of the components of the component contains more than the GB/T
26572 standard Set of limited requirements.
X: The content of the toxic and hazardous substances in all homogeneous
materials in the component is required under the limit of GB/T 26572 standard.
Note: this product is labeled “X” because there is no alternative
technology or component that can be selected at this stage.
Warranty information
- For any defect, in the judgment of our technician, caused under normal use, we are responsible for repairing free of charges 6 months commencing from the date of purchase at the discretion of our company.
- A valid warranty voucher or any original purchase invoice must be presented upon request of warranty service.
- During the warranty period, this warranty shall not apply to the product if (a) it has been explicitly modified or repaired in any way by persons other than technicians of our company, or(b) it has been damaged through misuse, malicious acts, negligence, and flow in any liquid, accident or natural calamities.
- All conditions refer to the Chinese version.
- If any damage causes to your product due to the wrong usage, our company will not take any
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Customer service center
Product name: POWER LIGHT User name____
Quality inspector: _ Contact address:____
Product code: __ Product code:_
Model number: D6 Contact number:____
Date of production:……………………………….
Stamp: ……………………… Date of purchase:…………………….
Standard: GB7000.1-2007,GB7000.204-2008
Company name: ShenZhen IDMIX Innovative Products Co.,Ltd
Add: Room1401, 3D Building, TianAnYunGu,
XueGang Road 2018#, Bantian Street,
Longgang District, Shenzhen, China
Tel: 0755-82913107