Astro Pneumatic Tool ‎3018 Digital Tire Inflator

BEFORE USE

When unpacking, check the parts diagram and part number listing on page 4 to make sure all parts are included. If any parts are missing or damaged, please call your distributor.

WARNING
Study, understand and follow all instructions provided with this product. Read these instructions carefully before installing, operating, servicing or repairing this tool. Keep these instructions in a safe accessible place.

INTENDED USE OF THE TOOL

Unit designed to inflate, deflate and measure tire pressure. Do not use this tool outside of the designed intent. Never modify the tool for any other purpose or use.
Caution: To help prevent personal injury Use of this product can expose you to chemicals including ethylene glycol, gasoline vapors and engine exhaust, which are known to the State of California to cause cancer, birth defects, or reproductive harm. For more information, visit www.P65Warnings.ca.gov. Always wear ANSI approved safety equipment, safety glasses, and clothing when using this product. Study, understand, and follow all instructions provided with this product. Failure to read and follow all warnings and operating instructions may result in damages and serious injury or death.

WARNING

• Always wear ANSI approved goggles when using this product. (Users and Bystanders).
• never use this tool for any application other than for which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool, modification of the tool, or use of the tool with accessories not designed for it could result in Serious injury or death.
• Always select the correct accessories of the correct size and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and adequately equipped area.
• Do not begin repairs without assurance that vehicle is in secure position, and will not move during repair.

PRODUCT INFORMATION

• AAA battery powered design. 4X the battery life and simplified battery installation.
• 21″ Stainless braided hose with bend gaurd for increased durability
• Maximum accuracy and 0.1psi resolution for use with TPMS (Tire Pressure Monitoring System)
• Displays KGF, PSI or BAR measurement
• Large face backlit LCD digital read-out
• Unit covered with rubber sleeve for extra comfort and durability
• Two position lever. 1st position deflates, 2nd position inflates.
• Easy Change Chuck System
• Works on with nitrogen systems and COz

FUNCTION KEY

ON/UNIT/LIGHT: Press once to turn on. Press again to turn on the backlight. When the unit is on, press for 3 seconds to switch units. If the display is unreadable or wili not change, press and hold the button for 8 seconds to restart.
TWIST/THREAD CHUCK ONTO VALVE STEM TO FULLY SEAL

Specifications

• Measuring Range: 3 – 175psi
• Units: PSI / BAR / KPA / KGF
• Resolution: 0.1 PSI
• Accuracy: Compliance with European 86/217/EEC and ANSI B40.1 0 – 58 psi +/- 1.2 psi 59 – 174 psi +/- 2.0 psi
• Working Temperature: 59 – 174 psi +/ – 2.0 psi
• Power: 32°F – 104°F (=0°C – 40°C)
• Battery Lifetime: AAA Battery 560hr

OPERATING INSTRUCTION

1. Remove tire valve cap.
2. With clip-on air chuck lever depressed, firmly press chuck onto tire valve stem and release lever, and ensure that no air leaks.
3. Press the grip to inflate. Press the grip half-way to deflate.
4. To turn on the inflator, press the ON/UNIT/LIGHT button. If it does not work, the inflator will be turned off automatically 90 seconds later.
5. When the inflator is on, press the ON/UNIT/LIGHT button to turn on the backlight in order to read the pressure in dark. The backlight will diminish automatically in 10 seconds. Backlight will not be activated by turning on the inflator, can only be activated by pressing the ON/UNIT/LIGHT button.
6. To change unit, when the inflator is on, press ON/UNIT/LIGHT button for at least 3 seconds. Then, press ON/UNIT/LIGHT button shortly after to choose the desired unit. The unit chosen will be set as default for following usage.
7. The inflator’s battery is 2*AAA, if voltage is low, the low battery signal on the top left of the LCD display will be flashing continuously to remind user to change the battery.
8. The measuring range is 0.2 – 12 bar (3 – 175psi). Reading resolution is 0.01 bar (0.1 psi). Maximum inlet pressure is 15 bar (218psi).

USAGE NOTES:

1. Inflator’s working pressure is 0.2 – 12bar (3 – 175psi), Max Inlet Pressure is 15bar (218psi).
2. If the pressure is between 7bar and 17 bar, the actual value will still be shown on the LCD, but the Maximum Permit table Error +/- 3psi is not guaranteed.
3. Maximum Pressure is above 17 bar, the LCD will show “—“, no actual value, and the inflator may be damaged. Accuracy is as below according to European Community Council Directive 86/217/EEC 0 – 58 psi +/- 1.2 psi 59 – 174 psi +/ – 2.0 psi

IMPORTANT

To avoid the risk of personal injury, especially to the eyes, face or skin, DO NOT direct the stream at any person.

BATTERY INSTALLATION INSTRUCTION

1. Peel back the rubber sleeve
2. Pry the cover open with a fingernail or flathead screwdriver (care to hold down the cover, as the cover is under spring tension.)
3. Install 2 AAA batteries in the indicated orientation
4. Snap battery cover shut
5. Reinstall rubber sleeve

TROUBLESHOOTING GUIDE

button for 8 seconds to clear. Or replace unit battery. Unit uses AAA battery. (See Product Manual for instructions on how to change battery)| ****

AAA batteries

Unit doesn’t turn on| Replace unit battery. Unit uses AAA battery. (See Product Manual for instructions on how to change battery)| AAA batteries

Unit is not deflating

| 1) Examine the Air Chuck (3018-17) to see if pin is broken. (see Image 1 below)| ****

3018-17

2. If pin is broken order part # 3018-17 – Air Chuck
3. To begin repair unscrew broken chuck from hose and replace with new chuck.

   ---

Air Leak (Valve Assembly)

| 1) Air leaks are usually caused by worn o-rings in the Valve Assembly.|

n/a

(P4 O-ring)

2. To begin repair simply remove Circlip (3018-09) and Lever Pin (3018-13) to gain access to the Valve Assembly. Unscrew Valve Base Assembly (3018-12) and pull out Valve Assembly.
3. Replace o-rings on valve assembly with P4 O-ring. Check Spring (3018-10) and ensure Spring is not broken or damaged
4. Replace Valve Assembly onto unit and tighten Valve Base Assembly (3018-12). Replace Lever Pin (3018-13) and Circlip (3018-09)

   ---

No Handle Spring Action

| 1) No handle spring action is usually caused by broken spring| ****

3018-10

2. Order part # 3018-10 – Spring
3. To repair simply remove Circlip (3018-09) and Lever Pin (3018-13) to gain access to the Valve Assembly. Unscrew Valve Base Assembly (3018-12) and pull out Valve Assembly
4. Replace broken Spring (3018-10)
5. Replace Valve Assembly onto unit and tighten Valve Base Assembly (3018-12). Replace Lever Pin (3018-13) and Circlip (3018-09)

PARTS BREAKDOWN

Call 1.800.221.9705 for questions concerning the performance of the product or other inquiries.

Parts List

3018-VSA

| Air Valve Rebuild Kit

(includes part numbers 11, 11B01,

11B02, 12, 12B01, 12B02, and 12B03.)

| 3018HSS| Stainless Hose with Air Chuck

1-YEAR LIMITED WARRANTY

• Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for 1 year (except where noted on our price schedule) from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship, or other causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this warranty free of charge. The distributor should direct the original user to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase a copy of the warranty card, and a short note explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro will replace free of charge parts of this product that fail within 1 year of first use by the original user. Items included in this category include but are not limited to kits, hand tool kits and any other product where multiple items or components make up the unit. Please contact the phone number below to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all warranty repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners.
• This warranty is instead of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you.
  PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING 1-800-221-9705 FOR INSTRUCTIONS

FAQs

What is the pressure range of the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The Astro Pneumatic Tool 3018 Digital Tire Inflator has a pressure range of 3-175 PSI.

What types of measurement units does the Astro Pneumatic Tool 3018 Digital Tire Inflator display?

The Astro Pneumatic Tool 3018 Digital Tire Inflator displays PSI, Bar, Kgf/cm², and kPa.

How accurate is the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The Astro Pneumatic Tool 3018 Digital Tire Inflator is accurate to ±1% of the reading.

What type of display does the Astro Pneumatic Tool 3018 Digital Tire Inflator feature?

The Astro Pneumatic Tool 3018 Digital Tire Inflator features a backlit LCD display.

What kind of batteries does the Astro Pneumatic Tool 3018 Digital Tire Inflator use?

The Astro Pneumatic Tool 3018 Digital Tire Inflator uses 2 AAA batteries.

How long is the hose on the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The hose on the Astro Pneumatic Tool 3018 Digital Tire Inflator is 21 inches long.

What is the material of the hose on the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The hose on the Astro Pneumatic Tool 3018 Digital Tire Inflator is made of stainless steel with a braided design.

What is the purpose of the dual function lever on the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The dual function lever on the Astro Pneumatic Tool 3018 Digital Tire Inflator allows for inflating and deflating tires.

What safety features does the Astro Pneumatic Tool 3018 Digital Tire Inflator have?

The Astro Pneumatic Tool 3018 Digital Tire Inflator includes a rubber sleeve for shock resistance and comfort.

How does the Astro Pneumatic Tool 3018 Digital Tire Inflator notify users of low battery?

The Astro Pneumatic Tool 3018 Digital Tire Inflator displays a low battery signal on the top left of the LCD screen.

How do you change the measurement units on the Astro Pneumatic Tool 3018 Digital Tire Inflator?

To change the measurement units on the Astro Pneumatic Tool 3018 Digital Tire Inflator, press and hold the ON/UNIT/LIGHT button for 3 seconds and select the desired unit.

What should you do if the Astro Pneumatic Tool 3018 Digital Tire Inflator shows an inaccurate reading?

If the Astro Pneumatic Tool 3018 Digital Tire Inflator shows an inaccurate reading, check and replace the batteries or reset the unit by holding the power button for 8 seconds.

What should you do if the Astro Pneumatic Tool 3018 Digital Tire Inflator does not turn on?

If the Astro Pneumatic Tool 3018 Digital Tire Inflator does not turn on, replace the AAA batteries and ensure they are installed correctly.

What is the working temperature range of the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The Astro Pneumatic Tool 3018 has a working temperature range of 32°F - 104°F (0°C - 40°C).

What is the hose material on the Astro Pneumatic Tool 3018 Digital Tire Inflator?

The Astro Pneumatic Tool 3018 has a 21 stainless braided hose.

What is the maximum pressure the Astro Pneumatic Tool 3018 Digital Tire Inflator can measure?

The Astro Pneumatic Tool 3018 has a maximum pressure of 12 bar (175 psi).

Download this manual:Astro Pneumatic Tool ‎3018 Digital Tire Inflator User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>