SHOKZ AS800 Aeropex Open-Ear Bluetooth Bone Conduction Sport Headphones User Guide

: June 5, 2024
: SHOKZ

Table of Contents

How to Set Up Aeropex
Multifunction Button (A)
Speciﬁcations
LED Indicator
Multipoint Pairing
Moisture Detected Alert
How to Reset Your Headphones
Optional Accessories
Manufacturer
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aeropex
User Guide

How to Set Up Aeropex

1. Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete.
2. Pair
Start with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
3. Connect
Open your device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue one time.

Multifunction Button (A)

Function	Action	Prompt / “Audrey Says'””
Play / pause music	Click once	One beep
Skip to next song	Double-click
while music is playing	One beep
Back to previous song	Three-click
while music is playing	One beep
Answer call	Click once	Two beeps
End call	Click once	One beep
Answer call waiting and hang up on current caller	Press and hold for 2
seconds	One beep
Reject a call	Press and hold for 2 seconds	Two beeps
Prompt device’s voice assistant	Press and hold for 2 seconds	Device beep
Redial last number	Double-click (when idle)	“Redial last number”

Volume+ / Power Button (B); Volume- Button (C)

Function	Action	Prompt / “Audrey Says™”
Power on	Press and hold volume+ for 2 seconds	“Welcome to AfterShokz”
Power off	Press and hold volume+ for 3 seconds	“Power off”
Mute	Press and hold both buttons for 2 seconds while on a call	“Mute on” or

“Mute off”
Change EQ setting| Press and hold both buttons for 3 seconds while music is playing| “EQ changed”
Check battery status| Click the volume+ or volume- button while music is paused| “Battery high/Battery medium/ Battery low/Charge me”
Adjust volume| Click the volume+ or volume- button to adjust the volume while music is playing| One beep

Speciﬁcations

Part number                                                  AS800| Frequency response| 20Hz~20kHz
---|---|---
Speaker type           Bone conduction transducer| Sensitivity| 105 ± 3dB
Bluetooth® version                        Bluetooth® v5.0| Microphone| -38dB ± 3dB
Wireless range| 10 m| Battery                                   Li-Polymer battery
---|---|---
Compatible proﬁles| A2DP, AVRCP, HSP, HFP| Weight| 26 g
Continuous play| Up to 8 hours| Standby time| Up to 10 days
Charge time| 2 hours| Warranty| 2 years
Frequency band| 2402MHz~2480MHz| Maximum RF output power| 4dBm
Charge voltage| 5V±5%| Water resistance| IP67
attery capacity| 145 mAh|

LED Indicator

Solid red	Charging
Solid blue	Charging complete
Flashes red and blue	Pairing mode
Flashes blue	Incoming call
Flashes red every 2 minutes	Low battery

Multipoint Pairing

Multipoint pairing allows Aeropex to be connected to two devices at once, allowing users to seamlessly transition between the two.

Start with your headphones powered off.
Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled.”
Open your first device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected”.
Turn your headphones off.
Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Open your second device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected.”
Turn your headphones off.
Turn your headphones on. Your headphones are now connected to both devices.
To turn multipoint pairing off: Press and hold the multifunction button and volume- button for 3 seconds. Audrey says “multipoint disabled.” More information: bit.ly/ASMultipoint

Moisture Detected Alert

These headphones can detect liquid such as water, sweat, and rain. If the headphones are plugged into the charger while wet, the LED indicator will flash red and blue. The headphones will also vibrate and emit a beep. If this happens, remove the charging cable from the headphones, dry them completely and then proceed with charging.

How to Reset Your Headphones

Start with your headphones powered off.
Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button, volume+ button and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
Turn your headphones off. Aeropex is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)
Use headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

Roll earplugs firmly between fingers and place them in the ears.
While music is playing adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
Switch EQ to the original setting when you take out the earplugs.