DIHOOM B08V1NHVC8 Wi-Fi Battery Solar Camera User Guide

DIHOOM B08V1NHVC8 Wi-Fi Battery Solar Camera

This guide is applicable to various types of battery cameras. Some of the illustrations are based on BA 12-H.

PACKING LIST

Battery camera

Solar Camera

Interface description

Battery camera

Solar Camera

Solar Dome Camera

The instructions of LED light

• Green light+ red light is always on: The camera is be,ng previewed remotely (privacy light)
• Green light is on for 1 s: The device is turned on or is woken up
• The green light flashes continuously: Upgrading
• Green light is always on: Charging
• Red light flashes 3 times: Power off
• Red light flashes countinuously fast: Matching code
• Red light flashes countinuously slowly: Connecting to the internet
•  Red light is always on: Low battery

Button operations:

• Press and hold 2s in the off state: Power on (green light for 1s)
• Press countinuously for 3 time: Power off (red light flashes 3 times)
• Press and hold for 8s: Reset to enter the pairing state (red light flashes)

Working network diagram

The battery camera supports 3 connecting modes:

1. Remote view by connecting the router (as the picture shows):
2. Direct connection through mobile phone (as the picture shows):
3. Pair to wireless NVR (WiFi/4G Gateway, WNVR, Touch screen)(as the picture shows).

When remote view by connecting the router, the camera’ WIFI should be connected to the router and the video is stored on the SD card of the camera or on the Cloud. When using in the local direct connecting mode, the WIFI of your mobile phone should be connected to the camera and the video can only store on the SD card of the camera. When working by pairing to the wireless NVR, the video is stored on the NVR and you can use mobile phone remotely to view and set up the camera through the wireless NVR.

Setup and installation

Boot up
When remote view by connecting to the router and direct connection method, please boot the device after insertting the SD card . When using by pairing to the wireless NVR, please make sure the memory(SD card, HDD etc.) of the wireless NVR is ready.

Battery camera
Please press the button for 2s to turn on the battery camera. If the button cannot be turned on, please plug in the charging power cord and the camera will turn on automatically.

Solar Camera
Plug the power cord of the solar panel into the tail cable of the solar battery camera

If you cannot turn on the phone after plugging it in, please open the speaker cover and plug in the power supply to charge or put the solar panel in the sun for 1 ~ 2 hours and try again

Software Installation
APP Download and Installation Users can search “EseeCloud” on APP store or “IP PRO” onGoogle Play.or scan the QR code below to install the APP.

Note: For iOS system, it requires iOS 9.0 version or above. For Android.Android 5 .0 or above.

Account login
Account login: On the login interface, enter the account/phone number/email, and the corresponding password, and click the “OK” button to log in. Third- party login: APP supports third-party login. Click the third-party social software icon, jump to the APP to complete the authorization and log in .

Instructions of adding the camera
Adding method 1: Scanning directly the QR code on the camera when the battery camera is used by connecting the network and local direct way.

1. 1.Put both of your mobile phone and camera near the router, and the distance should be 30-100cm
2. After the battery camera is power-on, there is a voice prompt “start match code” and the red LED light is flashing. (Otherwise please press the SYNC button on the camera for 8 seconds, it will be available after the voice prompt “reset successfully”)
3. Open the APP and click on the • +’ in the upper right corner to enter the scan code interface:
4. Scan the QR code on the device
5. On the search device interface, click “Add”;
6. Reset the device and wait for the device indicator to flash and proceed to the next step;
7. To view and use via WiFi or other networks, please select Remote View: If there is no network, if you connect to the camera at close range.please select Direct Connection:

Adding mode when remote view

1. Click “Remote View”, choose the WIFI the device needs to connected with, enter the password and click “next step”.
2. Using the device to scan the QR code on the mobile phone according to the operation the figure shows, then proceed to the next step after hearing the prompt tone.

Adding mode of local direct connection

1. Click “local direct connection”, set a password for the WIFI of the device itself and proceed to the next step
2. Using the device to scan the OR code on the mobile phone according to the operation the figure shows, then proceed to the next step after hearing the prompt tone.
3. After connecting with its own WiFi according to the guiding interface, return to APP;
4. Set the name and password for the device then you can add it to the device list;

Note: The direct connection needs to be maintained with the device’s own WiFi connection in order to preview the video of the device normally.
Adding method 2: To use with wireless NVR, please first power the wireless NVR and connect it to the Internet. After adding the wireless NVR by scanning the ID OR code on the body of NVR or displayed on the screen with the APP, you can check the battery camera on the APP.

View Alarm, Preview and Playback

1. Click the push information or ‘info” button to view the alarm information of the camera.
2. Click the corresponding play icon on the device list to enter the preview interface to view real-time video and have voice intercom.
3. Click the playback or cloud icon to view the video which is on the device or in the cloud.
4. Tap the share icon to share the camera to others.

Installation and placement mode

1. .Place on a desk or table, As shown below.
2. Fix the battery camera on the wall or glass

Solar Camera
Use the mounting sticker to locate and bore holes, and the cement wall must be nailed into Adjust the camera’s pitch angle to a proper position and tighten the fixing screws:

Solar Dome Camera
Use the mounting sticker to locate and bore holes, and the cement wall must be nailed into the rubber plug;

Adjust the camera’s pitch angle to a proper position and tighten the fixing screws;

Match code the camera to wireless NVR

The battery camera shipped with the kit has already been paired with the wireless NVR, no code matching is required. After the pairing information of the camera and wireless NVR is cleared, you need to match code again.

1. Place the battery camera and the wireless cameraM’ireless Touch Screen System /base station within 30-100 cm.
2.  While the battery camera is turned on, press and hold the SYNC button for 6 seconds.
3. When the indicator light of battery camera become to red light and fast flashing. that means enter the code matching mode.

Wireless touch screen system
Right-click the mouse and select “Wireless Add” to check whether it is added to the device. If yes, click to exit; otherwise, repeat steps 2 and 3 above.

Wireless touch screen

1. Click the screen, click the “home” icon, and click the [Match Code] module.
2. Click the “Match Code” button. After the adding is successful, click the “Stop” button. Other­wise, Otherwise, repeat steps 2 and 3.

Base station
Press the SYNC button of the base station for 3 seconds, and hear the voice prompts “Start matching code”, that is, the base station is in matching code mode. When the base station prompts “matching code successfully”, means the matching code is completed, if the base station prompts “The new device is not found’, Please repeat steps 2 and 3 above.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions.may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio{TV technician for help.

This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body.

FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION
Caution the user that changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>