**Electrolux EHE6879 Refrigerator User Manual

**

CONGRATULATIONS

Dear Customer,

Congratulations and thank you for choosing our refrigerator. We are sure you will find your new refrigerator a pleasure to use. Before you use the relevant sections of this manual, which provides a description of your refrigerator and its functions.

To avoid the risks that are always present when you use an electric appliance, it is important that the refrigerator is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards.

We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.

After unpacking the refrigerator, please check it is not damaged. If in doubt, do not use the refrigerator but contact your local Electrolux Customer Care Centre.

The symbols you will see in this booklet have these meanings:

WARNING
This symbol indicates information concerning your personal safety.

CAUTION
This symbol indicates information on how to avoid damaging the refrigerator

IMPORTANT
This symbol indicates tips and information about use of the refrigerator

ENVIRONMENT
This symbol indicates tips and information about economical and ecological use of the refrigerator

Conditions of use

This refrigerator is designed and intended to be used in normal domestic applications only.
Record model and serial number here:

Model number: ……………………………………………………………..
Serial number: ……………………………………………………………….

IMPORTANT SAFETY INSTRUCTIONS

NOTE: You must read these warnings carefully before installing or using the refrigerator. If you need assistance, contact your customer care centre. The manufacturer will not accept liability, should these instructions or any other safety instructions incorporated in this book be ignored.

WARNING

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• It is essential the power point is properly earthed to ground. Consult a qualified electrician if you are unsure.

• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

• Unplug the refrigerator before cleaning or moving it to avoid electric shock.

• Never unplug the refrigerator by pulling the electrical cord as this may damage it. Grip the plug firmly and pull straight out.

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Don’t use a steam cleaner. If live components come into contact with condensing steam, they may shortcircuit or cause an electric shock.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. If pressurised aerosol containers bear the word flammable’ and/or a small flame symbol, do not store them inside any refrigerator or freezer. If you do so you may cause an explosion.

• Do not damage the refrigerant circuit.

• This appliance contains insulation formed with flammable blowing gases. Avoid safety hazards by carefully disposing of this appliance.

• If you wish to discard this refrigerator, please contact your local authorities and ask for the correct method of disposal.

• When you dispose of your old refrigerators and freezers, remove any doors. Children can suffocate if they get trapped inside.

• The plug must be accessible when the appliance is in position.

• Never try to repair the refrigerator yourself, only use a qualified or authorized service person for repairs.

• Never put the appliance in a location that is too cold or is unprotected, for example in a garage or on a veranda. The ambient should be above 10°C.

• The water tank has to be removed from the door only for cleaning purposes and to fill the portable water only.

WARNING

R600a refrigerant warning

This appliance contains flammable R600a refrigerant. Avoid safety hazards by carefully installing, handling, servicing and disposing of this appliance.

• Ensure that the tubing of the refrigerant circuit is not damaged during transportation and installation.
• Leaking refrigerant may cause eye injuries or ignite.
• The room for installing appliance must be at least 1m3 per 8g of refrigerant. The amount of refrigerant in the appliance can be found on the rating plate inside the appliance.
• If you are unsure of the refrigerant check the rating plate inside the refrigerator compartment.
• It is hazardous for anyone other than an Authorised Service Person to service this appliance. In Queensland Australia the Authorisation Service Person MUST hold a Gas Work Authorisation for hydrocarbon refrigerants to carry out servicing or repairs which involve the removal of covers.
• Keep ventilation openings in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

FEATURES AT A GLANCE

1. Ice Maker
2. Air distributor – Multiflow
3. Deodoriser (air filter
4. Flip up glass shelf
5. Slide/fold glass shelf
6. Left glass shelf
7. Right glass shelf
8. Crisper shelf cover
9. FreshSeal crisper
10. FreshSeal crisper
11. Left Snack Zone compartment
12. Right Snack Zone compartment
13. Upper fixed door bin
14. Internal tank
15. FlexStorTM dairy bin
16. FlexStorTM 1/3 bin
17. FlexStorTM 2/3 bin
18. Egg tray
19. Expandable bin
20. Bottle storage bin
21. Adjustable left hinge
22. Adjustable right hinge
23. FlexFreshTM drawer
24. Drawer divider
25. Upper freezer drawer
26. Lower freezer basket
27. Lower freezer basket divider
28. Refrigerator/Freezer control panel
29. Water and Ice Dispenser
30. FlexFreshTM drawer control panel

INSTALLING YOUR NEW APPLIANCE

Unpacking

ENVIRONMENT

Most of the packing materials are recyclable. Please dispose of those materials through your local recycling depot or by placing them in appropriate collection containers.

Important – check for any damages or marks. If you find the refrigerator is damaged or marked, you must report it within 7 days should you wish to claim for damage/ marks under the manufacturers warranty. This does not affect your statutory rights.

Clean your refrigerator thoroughly following the instructions in the “Cleaning” section and wipe off any dust that has accumulated during shipping.

Locating the refrigerator

CAUTION
Automatic aerosol systems (such as insect control) should not be located adjacent to the product as the spray may cause long term damage to the external plastics of the appliance.

Do not put the refrigerator in a location that is too cold or is unprotected, for example in a garage or on a veranda. The ambient temperature should be above 10°C.

Put the refrigerator in a dry place avoiding areas of high moisture or humidity.
Ensure the refrigerator is located on an even surface.

Adequate ventilation around your refrigerator

The diagram below shows the recommended airspace to allow for ventilation of your refrigerator.

When positioned in a corner area, spacing of right side at least 219 mm and left side at least 310 mm on the hinge side will allow the doors to open enough to enable the removal of bins and shelves.

NOTE: Doors are designed to sit proud of cabinetry (not flush). The clearances shown above are the recommended minimum clearances.

Installing your refrigerator

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:

NOTE: If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.

Door opening

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of refrigerator drawers and freezer baskets, the refrigerator should be in a position where both can be fully opened.

CAUTION

LED lighting

Your appliance is fitted with long life LED lighting. In the unlikely event the LED lights should fail, then the LED lights should be serviced by the service agent, to avoid a safety hazard. Refer to the warranty page for contact details.

Cabinet Leveling & Refrigerator Door Alignment (if necessary)
Guidelines for final positioning of your refrigerator:

• All four corners of the cabinet must rest firmly on the floor.
• The front should be slightly elevated to ensure that doors close and seal properly.
• Doors should align with each other and be level.

Most of these conditions can be met by raising or lowering the adjustable front rollers.

To level the cabinet using the front rollers:

1. Slightly open freezer drawer if the toe grill is installed. Lift the toe grill and gently pull forward.

2. Make initial cabinet adjustments by using the front roller height adjusting screws. Use a 3/8 inch socket wrench to turn the adjustment screws (1 per side).
   To raise: turn adjustment screw clockwise.
   To lower: turn adjustment screw counter clockwise.

3. Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable.

4. After unit is leveled, lower anti-tip leg using a 3/8 inch socket wrench until it firmly contacts the floor.

To make final door height adjustments:

1. Open freezer drawer to make lower hinge visible.
2. Insert 6mm Allen wrench into the shaft of the lower hinge.
3. Adjust the height by turning clockwise or counterclockwise. Turning clockwise will lower the door.
   Turning counterclockwise will raise the door. Default setting is to the lowest height when you receive your appliance.

Flipper Mullion

Adjust Flipper Mullion for proper connection with the mullion guide by ensuring the flipper mullion is folded and perpendicular to the fresh food door. If the mullion guide is not in the correct position, it could prevent the door from closing completely.

Installation of air filter (selected models)

The air filter is located in the top center of the fresh food compartment.

To ensure optimal filtering of refrigerator odors, you should change the air filter every six months. Your first complimentary air filter can be found in the crisper.

1. Remove the air filter cover by squeezing the sides of the cover together and removing from liner

2. Remove the old filter and discard it.

3. Unpack the new filter and slide it into the housing.
   The open face must (carbon media) of the filter should be installed facing the air port (hole) in the multiflow.

4. Replace the air filter cover by squeezing the sides and snapping it back into place.

ABOUT THE USER INTERFACE

Controls

External user interface

Deactivates after 12 hours.
2.| DRINKS CHILL TIMER| Quickly chills a drink inside the freezer compartment. Touch the Drinks Chill Key, a time value will display on the freezer temp display (in minutes) and can be changed using the +/- buttons. A tone will sound when the time has been input. Range is from 20-45 minutes in 5 minute intervals.
3.| ICE MAKER| When LED is lit, the ice maker is on.
When ice maker is in OFF state, the indicator will blink when dispensing ice. Press and hold for 3 seconds to turn ice maker on/off.
4.| LOCK| Press and hold for 3 seconds to enable/disable.
While in the locked state, you will not be able to change any settings on the display nor dispense ice and water. The indicator will flash and an audible warning tone is played.
5.| WATER| Press the “water” key to select water. An indicator light will be illuminated above the active feature.
6.| CUBE| Press the “cube” key to select cubed ice. An indicator light will be illuminated above the active feature.
7.| CRUSH| Press the “crush” key to select crushed ice. An indicator light will be illuminated above the active feature.
8.| LIGHT| Toggles dispenser light On and Off.
9.| HOLIDAY| Maximum energy efficiency when the user is away from the appliance for an extend period. Conserves energy by increasing the time between automatic defrost. Manually turned on/off
It also turns off automatically when the user opens one of those doors/drawers or press the lever (dispenser) after 30 minutes from the time it was turned on.
After turns it off, the product will recover the internal temp to set temperatures and the “Ice Maker” function will also recover the previous status (On or OFF) automatically. BUT other function status won’t be recover.
---|---|---
10.| PARTY| This bottom should set up the freezer in -23°C and the fridge in 0°C during 6 hours. After that, the product should return to the previous settings.
11.| QUICK CHILL| Quick chill is a faster rate for chilling food in the refrigerator compartment. Deactivates after 6 hours.
12.| ADJUSTING TEMP| Press either the + or – to adjust to desired temperature setting. Freezer temp – Control temperatures range From -23°C to -15°C.
Refrigerator temp – Control temperatures range From +1°C to +7°C.
13.| CHECK WATER| When the panel show “check water”, fill the internal tank up.

FlexFreshTM drawer control panel

Unlock

| Press the UNLOCK icon. It will lock automatically after 3 seconds without any interaction. A tone will sound once panel is locked/unlocked.

| Freezer| To change the drawer temperature when in the freezer temp setting, use the control panel display on the front door. Changing the temp on the display will change both the drawer temp setting AND the freezer compartment
3.| Ultra Chill| Choosing Ultra Chill will set drawer temperature to -2°C. A tone will sound to confirm choice.
4.| Cold Drinks| Choosing Cold Drinks will set drawer temperature to 0°C. A tone will sound to confirm choice.
5.| Deli Snacks| Choosing Deli Snacks will set drawer temperature to 3°C. A tone will sound to confirm choice.
6.| Wine & Champagne| Choosing Wine & Champagne will set drawer temperature to 7°C. A tone will sound to confirm choice

SETTING COOLING TEMPERATURES

NOTE: The recommended settings for a product installed in a kitchen is 3˚C for the fresh food compartment and -17˚C for the freezer.

IMPORTANT
If your product has food freezing in the fresh food compartment, increase the temperature setting 1 or 2 degrees.

If you place food within 1 inch in front of the air ports, there may be the chance of freezing food.

NOTE: Control features and alarms may vary by model.

Alerts and Alarms

Door Open

If a door has been left open for 5 minutes or more, an alarm will sound and the door open indicator will illuminate on the display. The alarm can be turned off by closing the door or pressing any key. Control panel will return to normal operations after the door is closed.

Error tone

An alarm will sound if the user tries to make a selection that is not available.

Automatic Ice & Water Dispenser 

Using the ice maker after installation

Before making ice for the first time, be sure to prime the water supply system. Air in new plumbing lines can result in two or three empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor.

Refilling the water tank

• The water tank must be placed on the door.
• Pour potable water through the funnel at the lid of water tank.
• Ensure that ice maker and dispenser is switched on.

Refilling the water tank

Priming the water supply system

1. Begin filling the system by pressing and holding a drinking glass against the dispenser.
2. Keep the glass in this position until water comes out of the dispenser. It may take about 1½ minutes.
3. Continue dispensing water for about four minutes to flush the system and plumbing connections of any impurities (stopping to empty the glass as necessary).

NOTE: The water dispenser has a built-in device that shuts off the water flow after three minutes of continuous use. To reset this shutoff device, simply release the dispenser paddle.

Only the first 26 ounces (750 ml) of dispensed water is chilled.

CAUTION
Do not fill the Water tank with anything other then clean water (Filtered or Mineral water).

Soft drink, juice, tea or hot water etc, can damage your automatic icemaker.

The Water tank can withstand a maximum water temperature of 60°C

Tip and Useful Information

Remove and clean ice bin and water tank once a month, discarding unused ice and water. This will ensure fresh ice and smooth operation of your ice maker.

Make sure your refrigerator is level to avoid uneven ice cubes.

Ice Maker operation & care 

After the refrigerator is installed properly and has cooled for several hours, the ice maker can produce ice within 24 hours. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the bin to fill completely.

Ice Maker and storage bin capacity

This ice maker should produce 2.5 to 3 pounds of ice per 24 hours. The ice bin will hold about 4 pounds of ice.

TURNING THE ICE MAKER ON AND OFF

IMPORTANT

Your ice maker is turned on at the factory so it can work as soon as you install your refrigerator. If you do not fill the water tank, set the ice maker’s On/ Off feature to Off; otherwise, the ice maker’s fill valve may make a loud chattering noise when it attempts to operate without water.

Ice production is controlled by the ice maker’s On/Off feature on the control panel. Pressing the On/Off feature turns the ice maker on & off.

NOTE: The ice maker also has a built-in plastic signal arm that automatically stops ice production when the ice bin is full. This signal arm should not be used to manually stop the ice maker.

IMPORTANT

Turning off the ice maker simply disables ice making. You will still be able to dispense existing ice, and you will still be able to dispense water.

Ice maker/Dispenser tips

• If your water tank is not filled or it is empty, turn off the ice maker as described in the previous section.

• The following sounds are normal when the ice maker is operating:

  • Motor running
  • Ice dropping into ice bin
  • Water valve opening or closing
  • Running water

• If you need a large quantity of ice at one time, it is best to get cubes directly from the ice bin.

• Ice cubes stored too long may develop an odd flavor.
  Empty the ice bin as explained below.

• When dispensing cubed ice, it is normal to have a small quantity of little pieces along with the whole cubes.

• To avoid splashing, dispense ice into your container before adding liquids.

• It is normal for ice to fill to the top of the ice bin.

CAUTION
If the water supply to your refrigerator is softened, be sure the softener is properly maintained. Chemicals from a water softener can damage the ice maker.

Cleaning the ice maker

Clean the ice maker and ice bin at regular intervals, especially prior to vacation or moving.

1. Turn off the ice maker.
2. Remove the ice bin by pulling straight out.
3. Empty and carefully clean the ice bin with mild detergent. Do not use harsh or abrasive cleaners. Do not place in dishwasher. Rinse with clear water.
4. Allow the ice bin to dry completely before placing it back into the freezer.
5. Place ice bin back into position. Turn the ice maker on.

Remove and empty the ice bin if:

• An extended power failure (one hour or longer) causes ice cubes in the ice bin to melt and refreeze together after power is restored, jamming the dispenser mechanism.
• If you do not use the ice dispenser frequently. Ice cubes will freeze together in the bin, jamming the dispenser mechanism.
  
  Removing Ice Bin

Remove the ice bin and shake to loosen the cubes or clean as explained above.

**CAUTION**
NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice bin and dispenser mechanism.
To loosen stuck ice, use warm water. Before replacing the ice bin, make sure it is completely dry.

IMPORTANT
When removing or replacing the ice bin, avoid rotating the auger in the ice bin. If the auger is accidentally rotated, you must realign the auger by turning it in 45 degree turns (see below) until the ice bin fits into place with the drive mechanism. If the auger is not properly aligned when replacing the ice bin, the refrigerator will not dispense ice. The fresh food door also may not close properly causing warm air to leak into the fresh food compartment.

Adjusting the ice bin Auger

STORAGE FEATURES

CAUTION
To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change. Allow the glass shelves to stabilize to room temperature before cleaning. Do not wash in dishwasher.

You can easily adjust shelf positions in the fresh food compartments to suit your needs. The shelves have mounting brackets that attach to slotted supports at the rear of each compartment.

Change the Position of a Shelf

1. Remove all food from shelf.
2. Lift the front edge up and pull the shelf out.
3. Replace by inserting the mounting bracket hooks into the desired support slots.
4. Lower the shelf and lock into position.

To adjust flip shelf:

1. Remove food from shelf.
2. Lift the right side edge of shelf upwards and push to the left towards ice maker

Flip Shelf

To adjust slide-under/flip shelf:

1. Pull front half shelf forward until its back drops down, then gently push front half shelf back and under back half shelf.

Silde-Under/Flip Shelf

2. With front half fully below back half, lift front of shelf to flip it upwards toward the back of the cabinet.

Sild-Under/Flip Shelf

Drawers

Your refrigerator includes a variety of storage drawers.

FreshSeal Crisper (with AutoHumidity filter)

Crisper drawers are designed for storing fruits, vegetables, and other fresh produce. Crispers have an auto humidity control (with replaceable AutoHumidity filter) on the side of each crisper under the cover.

To remove the AutoHumidity filter:

1. Reach to back of cover.
2. Pull up on cover.
3. Pull cover towards back of cabinet and remove.
4. Replace AutoHumidity filter.
5. Replace cover by reversing the steps above. Repeat for both crispers.

Opening Crisper Drawer

To remove the FreshSeal Crisper for cleaning:

1. Pull the drawer out until it stops.
2. Lift the front slightly and remove the drawer

Removing the FreshSeal Crisper

Recessed SnackZone

This drawer is ideal for storage of deli meats and cheese.
Slide back the cover to allow access to the drawers.

Opening the SnackZone

Doors

Storage bins

The doors to your fresh food compartment use a system of modular storage bins. All of these bins are removable for easy cleaning. Bins can be adjusted to your needs. Door bins are ideal for storing jars, bottles, cans, and large drink containers. They also enable quick selection of frequently used items.

To move door bin along a rail:

1. Tilt bin up so the back of the bin is off the door but the hook is still engaged.
2. Slide bin along rail to desired position.
3. Lower bin back into place.

To move door bin from rail to rail:

1. Lift bin up disengaging the hook.
2. Move bin to desired rail location.
3. Push bin hook into rail engaging the hook

Adjustable Door Bins

Freezer Features

Freezer Basket

To remove upper freezer basket:

1. Open freezer compartment completely.
2. Lift up and out to remove upper freezer basket.
   Reverse the steps to reinstall basket.

IMPORTANT
There are wheels on the bottom of the drawer. Make sure all wheels are aligned on their respective tracks for proper function. If drawer is not aligned properly, it will cause problems with the door operation.

NOTE: If basket is not resting on stabilizer bar retainer clips, the drawer will not close properly.

To remove lower freezer basket:

1. Open freezer compartment completely.
2. Lift the basket up and remove.

Reverse the steps to reinstall drawer.

Dividers
Grab hand hold on lower divider and pull up slightly to slide to next position. (The divider cannot be removed.)

Lower Basket Divider

GENERAL INFORMATION

CLEANING YOUR REFRIGERATOR

WARNING
BEFORE CLEANING: Turn the refrigerator off at the power point and unplug the cord to prevent any chance of electrocuting yourself.

Doors and exterior (white and silver):

You should only clean the doors with lukewarm soapy water and a soft cloth.

Stainless Steel:

Your stainless steel refrigerator is manufactured from mark-resistant stainless steel. This stainless steel has a special advanced protective coating that eases the removal of marks such as fingerprints and water spots. To keep its appearance, clean it regularly with lukewarm soapy water and a soft cloth.

Water Tank

The tank has to be removed from the door only for cleaning purposes, to fill the portable water only, the tank must be placed on the door and the funnel on the lid has to be used.

**CAUTION**
Never use stainless steel cleaners, abrasive pads or other cleaners that will scratch the surface. Damage to the appliance after delivery is not covered by your warranty.

Interior

Clean the inside of your refrigerator regularly with a soft cloth, unscented mild soap and lukewarm water. Thoroughly dry all surfaces and removable parts and avoid getting water on the controls. Replace removable parts, plug power cord in and switch the power on before returning the food.

Ice and water

Clean the components of the ice maker/water dispenser regularly with a soft cloth, unscented mild soap and rinsing thoroughly with lukewarm water. For further information on the care and cleaning of your ice maker, ice dispenser of water dispenser refer to the section “Ice and Water Models”

Water Tank Assembly

Clean the inside of the water tank regularly with a soft cloth, unscented mild soap and rinse thoroughly with lukewarm water to completely remove any soap residue.

Water tank cleaning:
The tank has to be removed from the door and lift the lid off water tank.

NOTE: When customer assembled tank to door :
To avoid water leaks ensure that tank nozzle fully engaged with housing socket.

Door seals

Always keep door seals clean by washing them with a mild detergent and warm water, followed by a thorough drying. Sticky food and drink can cause seals to stick to the cabinet and tear when you open the door.
Never use hot water, solvents, commercial kitchen cleaners, aerosol cleaners, metal polishes, caustic or abrasive cleaners, or scourers to clean your refrigerator.
Many commercially available cleaning products and detergents contain solvents that will damage your refrigerator. Use only a soft cloth with an unscented mild soap and lukewarm water.

CAUTION
To clean a crisper or freezer bin with telescopic extension slides, simply wipe with a damp cloth and warm soapy water. Never immerse the cover in water, as this could affect the operation of the slide.

Switching off your refrigerator

If you switch off your refrigerator for an extended period, follow these steps to reduce the chances of mould:

1. Remove all food.
2. Remove the power plug from the power point.
3. Thoroughly clean and dry the Interior.
4. Ensure that all the doors are wedged open slightly for air circulation.

FOOD STORAGE GUIDE

RECOMMENDED STORAGE TIMES FOR FRESH FOODS *

CATEGORY    PRODUCT                STORAGE TIPS

REFRIGERATOR   ULTRA CHILL        FREEZER

MEAT| Sausages and Mince        1-2 Days

Chops and Steak             3-4 Days

| 3-5 Days

5-7 Days

| 2-3 Months

4-6 Months

| Keep cold meat at the back of the refrigerator where it is coldest.
Cold Meats                  3-5 Days| 5-7 Days| 4-6 Months| Plastic can cause meat to sweat if stored in refrigerator for more than a day.
Roasts                        3-5 Days| 1 week| 12 Months| Roast can take up to 48 hours to defrost properly, transfer frozen roast to th refrigerator 2 days before use.
POULTRY| Chicken                      1-2 Days
Roast Chicken                3-5 Days| 5-7 Days
1 week| 2 Months
12 Months| If poultry takes on a smell or colour you are unsure about it is best to throw it out.
Eggs                          6 Weeks| Not Suitable| Not Suitable| Whole eggs are not suitable for freezing, slightly beaten eggs may be frozen for four months.
SEAFOOD| Whole fish and fillets        2-3 Days Lobster and Crab 1-2 Days
Prawns                       1-2 Days| 5-7 Days
3-5 Days
3-5 Days| 2 Months
2 Months
2 Months| Store in an airtight container or foil.
Never freeze prawns in salty water as this will dehydrate the flesh.
DAIRY| Milk                            Until Expiry Date
Yoghurt                      7- 10 Days| Not Suitable Not Suitable| Not Suitable Not Suitable| If dairy takes on a smell or colour and you are unsure about it, it is best to throw it out
Hard Cheeses                2 Weeks – 2 Months| 1-2 Months| 2 Months (Grated)| Depending on the variety hard cheese can last from 2 weeks to 2 months.
Soft Cheeses                  1-2 Weeks| 2-4 Weeks| Not Suitable| Texture may change depending on the type of soft cheese
Butter                        8 Weeks| 3-4 Months| 12 Months|
FRUIT & VEGETABLES| Every fruit and vegetable has a different shelf life.
Some stay fresh for a couple of days e.g. beans, others can last for a couple of months e.g. onions.| Not Suitable| 8-12 Months
When freezing chop and blanch in small portions.| Keep vegetables in the crisper and away
from the air vents to avoid freezing.
If you wash fruit and vegetables before
storing them make sure they are dry or
wrap in absorbent paper before storing
in the refrigerator as this can make them
 |  |  |  | susceptible to rotting.
 |  |  |  | Try to keep fruit and vegetables
 |  |  |  | separated as fruits that give off high
 |  |  |  | levels of ethylene (the ripening agent)
 |  |  |  | can prematurely ripen and spoil
surrounding vegetables

IMPORTANT
Please note, use this information as a guide only, actual storage times will vary depending on how you use your refrigerator.

inside the refrigerator.
Ensure the appliance is set up as per instructions on page 11.
Ensure that contents are not obstructing the cooling vents.
Ensure the door is not held open or is being opened too frequently.
Freezer is too warm.| Adjust temperature to a colder setting.
Ensure food is allowed to cool before placing inside the freezer.
Ensure the appliance is set up as per instructions on page 11.
Ensure that contents are not obstructing the cooling vents.
Ensure the door is not held open or is being opened too frequently.
Food is freezing in the refrigerator.| Adjust temperature to a warmer setting.
Ensure that fruit and vegetables are stored in the crisper. Items with a high water content should not be placed near the cooling vents.
Unable to change temperature settings.| Refer to function guide in Controlling Your Refrigerator.
Ensure that user interface is in “awake” mode before trying to adjust temperature settings.

Appliance noise

Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, like the floor, walls and cabinets, can make the sounds seem louder than they actually are. The following describes the kinds of sounds and what may be making them.

uses a variable speed compressor and fan that at start up and on warm days runs at a high speed to provide additional cooling.
When less cooling is required the compressor and fan will run at a lower speed Note that the compressor noise may seem louder at the start of the on cycle.

A clicking noise heard just before the compressor starts.| Nothing. This is normal as your new refrigerator has an automatic switching action of the temperature control, turning the compressor on and off.
Occasional gurgling, similar to water boiling.| Nothing. As each refrigeration cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator system.
Airflow noise.| Nothing, this is normal as your new refrigerator uses high efficiency fans to circulate air. Fan speed and noise may increase during periods of heavy usage or hot weather.
Rattling and other noises.| Ensure that the cabinet is level and stable, refer to Installation Instructions on page 11.
Check the surrounds of the appliance to ensure there is nothing touching or placed on top of the appliance.
Ensure that contents of the appliance are not placed in such a way that they are vibrating (such as bottles).

Crisper Operation

Concern                                     What to do

Excess moisture build up in crisper. It is normal for there to be some moisture and humidity in the crisper bin.| Ensure that the crisper is not over packed.
Adjust crisper humidity slides.
Crisper bin cannot be removed.| If crisper bin interferes with the door bins, remove door bins before removing crisper.
Position cabinet so that the door can be fully opened.
Freezing items in the crisper.
Adjust temperature to a warmer setting.

TROUBLESHOOTING

Refrigerator operation

Appliance will not run
It is normal for the freezer fan not to operate during the automatic defrost cycle, or for a short time after the appliance is switched on.| Ensure that the cord is plugged into a live power outlet and outlet is switched on.
Ensure that the household circuit breaker has not tripped or that the fuse has not blown.
The appliance maybe in defrost mode, check again in half an hour.
Compressor motor seems to run too long
At normal room temperatures, expect your motor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even more often.
The variable speed compressor and fan that at start up and on warm days runs at a high speed to provide additional cooling. When less cooling is required the compressor and fan will run at a lower speed.| Ensure that the doors are not held open.
Check that large amounts of warm food have not just been placed inside the appliance.
Note that the appliance will run more than normal just after you install it or when adjusting to temperature setting changes.
The exterior of the appliance is warm or hot to touch
This is normal because the appliance transfers heat from the inside out through the outer panels and the divider between the doors.| Ensure the appliance has the external clearances recommended in the section “Installing your new appliance”.
The exterior of the cabinet will be much warmer on warmer days it may even feel hot to touch, as the appliance is working harder.
User interface will not respond
To ensure settings are not accidentally changed the user interface will go into sleep mode when not in use.
Press any button to wake user interface.| Check that the user interface is in awake mode, refer to section “About the user interface”.
Check that the user interface is not locked, refer to section “About the user interface”.
If the user interface is frozen turn the appliance off for five minutes for the memory to clear, then turn back on.
Check that the user interface is not in Sabbath Mode, refer to control instructions. (I&W models only).
Alarms sounding| Check that all doors are fully closed.
 | Ensure that the over temperature alarm is not being activated by hot food placed in the freezer.
 | Check if the drinks timer has ended, refer control instructions.
 | Check if the Filter Replacement alert is activated, refer control instructions. (I&W models only)
Frost build up| Check that all doors are fully closed.
 | Ensure that the doors are not opened too often.
 | Ensure that the return air vents are not blocked with packaging.
 | Ensure the seals are clean and not obstructed.
Odours| The interior may need cleaning, refer to cleaning guide.
 | Ensure that food is stored correctly as some food, containers and wrapping can produce odours.
 | Check appliance for old or unusual food.
Lights not working
The LED lighting is designed to dim automatically if the door is left opened for more than 5 minutes and turn off completely if the door is open for more than 7 minutes. Closing the door will reset the timer.
The LED lighting is also designed to turn on gradually.| Ensure that the cord is plugged into a live power outlet and outlet is switched on.
Ensure that the household circuit breaker has not tripped or that the fuse has not blown.
Check that the user interface is not in Sabbath Mode, refer to control instructions.
Close and re-open the door. When door has been open for 5 minutes the lights fade to 50% then after 7 minutes they will turn off.
Concern| What to do
---|---
Freezer door pops open.| This is normal and should re-close. This happens when the refrigerator door is closed too quickly.
 | If the freezer door stays open, it indicates that the appliance needs to be tilted backwards a little further. Refer to section “Installing your new appliance”.
Self close not working.| Check if your appliance has self closing hinges as not all models do.
 | It indicates that the appliance needs to be tilted backwards a little further. Refer to section “Installing your new appliance”.
Door not sealing properly| Ensure there is nothing that is preventing the door from closing such as appliance contents or items placed near the appliance.
 | Ensure that the crisper/freezer bin is closed completely. Refit if required as referred to in the section “Using your refrigerator”.
 | Ensure the appliance is set up as per recommendations.
Door difficult to open and close| If the door is difficult to open just after you have closed it this is due to the pressure equalising, the door will open normally after a few minutes.

Automatic Ice maker system

Ice maker does not produce ice or not enough ice
The ice maker is designed to produce a tray of ice approximately every 3 hours, depending on room temperature and water temperature..| Ensure that the cord is plugged into a live power outlet and outlet is switched on.
Ensure that water is connected and turned on and there are no kinks in the water line.
Ensure that the Ice Maker is switched on at the user interface refer to “About the User Interface” for details.
Check that the water filter is not blocked or out of date.
Check the water supply flow rate.
If the freezer compartment is too warm, refer to “freezer is too warm” then wait 24 hours for the freezer to reach ideal temperature.
Turn the unit off at the mains and leave for 2 minutes then turn the appliance back on (this will reset the ice maker unit). Check for ice production after 24 hours.
Check that there is no obstruction under the ice maker and ensure the ice bin is fitted correctly.
Ice has bad odour or taste| Cover food to ensure ice does not absorb foreign odours.
 | Check that the water filter is not out of date.
 | Interior of appliance or ice bin may require cleaning, refer to “Cleaning your refrigerator”.
 | Discard stale ice monthly and allow ice maker to produce a fresh supply.

If you still require service

If you have a problem, and the problem persists after you have made the checks mentioned, contact your nearest Electrolux approved Service Centre or the dealer you bought the refrigerator from. Be ready to quote the model number, the 9-digit PNC and 8-digit serial number, which is stated on the label inside the refrigerator compartment.

CONTACT DETAILS ELECTROLUX CUSTOMER CARE

Philippines
Consumer Care Center Toll Free : 1-800-10-845-CARE(2273)
Consumer Care Hotline : (+63 2) 845-CARE(2273)
Electrolux Philippines, Inc.
10th Floor. W5th Avenue Building
5th Avenue Corner 32nd Street
Bonifacio Global City,
Taguig Philippines 1634
Trunkline: +63 2 737- 4757
Website : www.electrolux.com.ph
Email : wecare@electrolux.com

Singapore
Consumer Care Center Tel: (+65) 6727 3699
Electrolux S.E.A. Pte Ltd.
1 Fusionopolis Place,

07-10 Galaxis, West Lobby

Singapore 138522.
Office Fax : (+65) 6727 3611
Email : customer-care.sin@electrolux.com

Malaysia
Consumer Care Center Tel: 1300-88-11-22
Electrolux Home Appliances Sdn. Bhd.
Corporate Office Address: Unit T2-7, 7th Floor,
Tower 2, PJ33,No. 3, Jalan Semangat, Seksyen 13,
46200 Petaling Jaya, Selangor.
Office Tel : (+60 3) 7843 5999
Office Fax : (+60 3) 7955 5511
Consumer Care Center Address: Lot C6, No. 28,
Jalan 15/22, Taman Perindustrain Tiong Nam,
40200 Shah Alam, Selangor
Consumer Care Center Fax : (+60 3) 5524 2521
Email : malaysia.customercare@electrolux.com

Share more of our thinking at electrolux.com.
P/No: A10883112/A
MDR4_Aug’18

References

• Electrolux - white goods and household appliances | Electrolux
• Electrolux Spares & Accessories | Next Day Delivery | Electrolux UK
• Electrolux Philippines | All Home Electrical appliances & Kitchen appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>