Cronte Technology MAA-S700 Fingerprint Glass Door Lock User Manual

Cronte Technology MAA-S700 Fingerprint Glass Door Lock

Preface

• Thank you for choosing the smart fingerprint glass door lock
• To help you properly use the Smart Lock Product (hereinafter referred to as “the Product”), please read the instructions carefully before installing .
• For the actual specifications and configurations of the products described in this manual, please refer to the relevant agreements or consult with retailer.
• If you fail to operate according to the instructions in the manual, or ask non-our technical personnel to repair or change the product, we will not bear any responsibility for the damage caused thereby.
• The graphs and charts provided in this manual are only for the purpose of explanation and description and may differ from the actual products. In addition, the actual specifications and configurations of the products may be
• changed from time to time as required. Therefore, they are different from the contents in this manual.
• In order to provide better service, the products and contents described in this manual are subject to update, improvement or modification without prior notice.
• If you find any inconsistency between the actual situation of this product and this manual, or if you want to get the latest information or have any questions and ideas, please feel free to call our after-sales service department.

Technical parameters

Power supply

| ****

1.5V AA X 4 or USB 5VDC

---|---

Standby current

| <55mA(more than one year battery life)

Working current

| ****

<250mA(strong driving force)

Static current

| <50uA(Super long standby)

Unlock mode

| Fingerprint, password, ID card, remote kit (optional)

Password capacity

| ****

s 240 groups

Fingerprint capacity

| ****

s 200 groups

CARD capacity

| ****

s 240 sets

Record queries

| ****

s 250 groups

Resolution

| 500 dpi

Rejection rate

| ****

S0.15%

False recognition rate

| s 0.0000 4%

The working temperature

| ****

-30-60’C

Relative humidity

| ****

20-93%

Setting and usage

After lighting up the keyboard, long press the”ESC”key to enter the Settings menu.In factory experience mode, you can directly enter the Settings menu. After registering the administrator, you need to confirm the administrator password before entering. (Note: 2, 8, 4, 6 are the upper, lower, left and right movement keys,OK is the confirmation key,ESC is the return key)

1.  Add administrator (fingerprint, password and card can be set separately) Password: Press OK key to add the password. Enter the password twice to add the password. Card: PressOKkey to add the card. Swipe the card to add the card. Fingerprint: press OK key to add the fingerprint, input the fingerprint three times to add complete.

2.  Add user (fingerprint, password and card can be set separately)
   Password: Press OK key to add the password. Enter the password twice to add the password.
   Card: Press OK key to add the card. Swipe the card to add the card.
   Fingerprint: press OK key to add the fingerprint, input the fingerprint three times to add complete.

3.  Delete users
   Press OKto delete the user and select the user to delete.
   Press OK an·d then press 6 to select “Yes” and press OK to finish delete

4.  System information
   Press OK key to enter the system information query, you can see user capacity,Unlock records, fingerprint capacity , remote access capacity, battery voltage.

5.  Unlock record (press OK key to enter unlock record query, press ESC key to return)

6.  Remote Kit Settings (press OK key to enter the remote kit Settings)

   •  Add remote kit: press OK key, then short press remote kit for pairing, 16 sets of remote kit can be added.
   •  Delete all remote kit: press OKkey,then press 6 to select “Yes”, and press OKkey to complete user deletion.

7.  System Settings

   •  Time setting: Press OK toenterthetime setting; 2,8 and 4,6 are upper, lower, left and right movement keys; OK is confirmation key;ESC is return key.
   •  Volume setting: Press 6 to increase volume, and press 4 to decrease volume.
   •  lock delay: press 6 to add time, press 4 to reduce time.
   •  Magnetic delay: press 6 to add time, press 4 to subtract time.
   •  Card wake-up: Press 4 and 6 key to select on/off.
   •  Language: press 4 and 6 key to switch Chinese/English.

8.  Restore factory Settings
   Press OK to resume factory Settings, press 6 to select “Yes” and press OK to confirm.

9.  Temporary one-time password
   Press OK key to enter one-time password setting. Six one-time passwords can be set. One-time password can only be used once

10.  Unlocking period
    Press OK key to set the lock opening period. From Sunday to Saturday, 3 lock opening periods can be set every day.

Normally open mode setting
After opening the lock, long press the backside “Open door button ” to enter the normal opening mode. Under the long opening mode, the lock will not be automatically locked. After manually locking, it will exit the normal opening mode.

Internal lock setting
After locking, long press the backside “Open door button ” and enter the door lock mode Under the door lock mode, only the administrator/one-time password can open the lock at the outdoor.

Manually unlock/lock
The door can be manually unlocked/locked by the “Open door button ” and the manual door opening knob.

Installation instructions

Attach the main lock body/sub-lock fixing plate

1.  Stick the double-sided adhesive tapes to the flat side of the adhesive tapes, select the appropriate installation height, and stick the adhesive tapes to the glass door (the upper and lower alignment of the adhesive tapes must be ensured). — The mounting plate of the main lock and door magnetic is pasted with double-sided adhesivetape and fixed on the glass door in piir llel alignment—
2. Install the main lock /door magnetic Push the main lock/door magnetic into place along the fixing plate respectively as shown in the figure
3.  Fixing the main lock and door magnetic Take off the battery cover, tighten the 6 screws of the main lock and door magnetic as shown in the diagram, and then put the rubber plug in the accessories package into the screw hole and press it flat.Then load the battery as shown in the diagram and close the batterycover. — Install the battery after installing the fixing screw of the main lock and door magnetic. Install the rubber plug and battery cover after the test product function is normal—
4.  Left-open/right-open direction adjustment method When left-open/right-open direction is needed to be reversed, remove the 6 screws on both sides of the rear lock body (battery holding part), rotate the front lock body 180, and then lighten the 6 screws.

Fault description

The phenomenon of

| ****

Reason

| ****

Elimination method

---|---|---

No response of unlock with ID card/fingerprint/ password/remote kit

| ****

1. The battery is  dead 2. Other

| ****

1. Change the battery or use emergency power

2. Restore factory Settings or contact after-sales service

The locking tongue does not move or quiver| ****

1. Doors are  not  aligned 2. Low battery

| ****

1.  Try aga in after the doors are aligned

2.   Unlock with emergency power

Unable to read fingerprints

| ****

1.   Dry and wrinkled finger skin

2.   After long use, the collection surface becomes unclean or has scratches

3.   The other

:, ,

| ****

1.   Make your fingers slightly moist to make your fingerprints clear

2.   Use non-drying adhesive tape to paste the dirts on the surface of the head

3.   Restore factory Settings or contact after-sales service

The door cannot be automatically locked

| ****

1.  The battery is dead

2.   Not automatic lock mode

| ****

1. Replace the  battery 2. Set to automatic

lock  door mode

Cannot set door

| 1 . Not be ing empowered 2. Not following t he steps| ****

card/fingerprint/password| 3. Inpu t   more  than  240 sets of door passwords,

more than 240 sets of card capacity and more than 200 sets of

fingerprints.)

| 2.  Operate according to the previous  door  lock setting.)

3.  Delete no open door card/fingerprint/password requ ired

Lock maintenance and maintenance

Daily maintenance and maintenance

1.  D o not let the lock face contact with corrosive substances, so as to avoid damaging the protective layer of the lock face and affecting the gloss of the lock face.
2.  If the door is deformed, it will cause the combined inclined tongue to enter the door frame box to have too much friction and cannot be completely extended. At this time, the position of the door gusset plate should be adjusted.
3.  After using the fingerprint window for a long time, the surface will be stained with dirt or wet. Please wipe it gently with a soft dry cloth.
4.  Please replace the battery immediately after the alarm of low battery, so as to ensure the normal use of the door lock.When replacing the battery, please pay attention to the positive and negative terminals.
5.  Do not use hard or sharp objects to mark the surface of the fingerprinting window (including fingernails).
6.  Each time a fingerprint is taken, the fingerprint part of the finger is flat against the fingerprint reader.
7.  If the lock is not flexible in rotation or cannot be maintained in the correct position, professionals should be asked to add mechanical lubricating oil to the lock core.
8.  Always keep lubricant at the rotating part of the lock body to ensure smooth trar,ismission and prolong service life. It is recommended to check once every six months or once a year, and check whether the fixing screws are loose to ensure the fastening.
9.  Alkaline batteries are recommended;Carbon and alkaline batteries and old and new batteries can not be mixed, depleted batteries please remove.

After-sales service

Principle of the warranty
Our company offers a lifetime service for the products we sell.The company will provide free warranty to repair service within one year from the date of purchase.But does not include any freight.
No free warranty service is provided under the following circumstances:

1.  If there is no product warranty card or valid purchase certificate, the warranty does not match the purchase certificate;
2.  Damage caused by human factors, including damage caused by use in abnormal working environment, use without instructions, etc.
3.  The user disassembles the machine without permission, repairs it by himself, modifies

Warranty Instructions

1. Please keep this warranty card properly for the maintenance voucher.
2. The product is subject to the national three-guarantee policy.
3.  If the customer buys the product within one year, the company will repair or replace it for free. If the product is damaged due to improper operation or other man-made damage, the company will charge the cost of spare parts and maintenance.
4. Within the warranty period, the user shall present the card and the shopping documents to obtain the warranty and replacement services.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>