Cronte Technology FD-SLI800KG 800KG Sliding Door Garage Motor Instructions

Cronte Technology FD-SLI800KG 800KG Sliding Door Garage Motor Instructions

WARNING TO THE INSTALLER AND USER

1. CAUTION! For personal safety it is important to follow all the instructions carefully. Incorrect installation or misuse of the product may cause serious harm to people .
2. Keep the instructions in a safe place for future reference.
3. This product was designed and manufactured strictly for the use indicated in this document. Any other usage not expressly indicated in this Document, may damage the product and/or be a source of danger.
4. CSD accepts no responsibility due to improper use of the automatic machine ( opener) or use other than that intended.
5. Do not install the machine in aflame subject to explosion hazard. Inflammable gasses or fumes are a serious safety hazard.
6. CsD will not’ accept responsibility if the rules of good workmanship are disregarded in the closing elements to be motorised, if any deformation occurs during use of the said elements.
7. Before carrying out any work on the system, turn off the electricity supply.
8. The safety devices(e.g. photocells, sensitive edges, etc…) may be used to prevent any potential risk in dangerous areas where the moving mechanism is located , such as crushing, dragging, or shearing.
9. CsD accepts no responsibility regarding safety and correct operation of the machine, should components made by manufacturers other than we be used in the system.
10. Do not make any alterations to the components of the automatic machine ( opener and accessory).
11. The installer must supply full information regarding operation manual of the system in the event of any emergency and provide the system user with the “INSTRUCTION” included with the product.
12. Do not allow children or other people to stand near any moving part of the opener or door construction while in operation.
13. Keep transmitters away from children to prevent the machine from being activated accidentally.
14. The user must refrain from attempting to repair or adjust the system personally and should only contact professional personnel .
15. Frequently examine the installation, in particular check cables, springs and mountings for signs of wear, damage or imbalance .Do not use if repair or adjustment is needed since a fault in installation or an incorrectly balanced door may cause injury.
16. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
17. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard.
18. Disconnect the supply when cleaning or other maintenance is being carried out, if the appliance is automatically controlled.
19. The temperature range marked on the drive should be suitable for the location.
20. The electrical cord plug must plug in indoor outlet or waterproof cover outlet.

1. Introduction

1.1 Dimension

• Built-in control board.
• Terminals for Push button, Photocell, Alarm lamp.
• Auto-closing is available, time delay is adjustable.

1.2 Technical Specifications

Specifications:
Voltage : AC150V-260Y 50HZ
Moterpower:300I[l, 3701, 5501, 7501, 9501W, 300ks-2000k
Motor speed: 1400 /min
0utput speed: 46.6/min
Starting current:3A
Running speed : 12m-20m/min
Max load: 300ks-2000k

2. Installation

• Before using the machine, check power supply, grounding, voltage, etc.
• Check whether it is connected according to the demand of wiring diagram.
• The gate should be pulled easily and smoothly manually when the worm gears are released .
• The worm gears will be coupled before power on.
• The product must be installed by professional person.

2.1 Example of a sliding gate operator installed

2.2 Installation and adjustment

2.2.1  Install baseplate on the ground, then, fasten the sliding motor on the base- plate.
Key: Ensure baseplate on level position.

2.2.2 Install the limit stopper or limit magnet at proper position on the steel rack.

Before place the limit stopper or magnet on the rack, the gear box of the operator must be released. As per Fig 6A or fig 6B, Use the key turn clockwise to release the gear.

Move the gate manually to the open limit and close limit, mark the points on the Rack, then, fix the limit Stoppers or Magnets at the limit points on the Rack.

NOTE: Magnet must be L0mm-2Omm space from the operator, and must be same height with the Magnetic switch inside of the operator.

3. Control Board

Mechanical limit

3.1 Diagram

9.2 Layout of PCB and Definition

1. LEDI opening lamp
2. LED? learning code lamp
3. LED3 closing lamp
4. LEDA stopping lamp
5.  LEDS open signal lamp
6. LED6 cycle signal lamp
7. LED7 photocell signal lamp
8. LEDS spacing signal lamp
9. YR l closing force set
10. YR 2 self closing time set

3.3 Learning process for adding the remote:

please press button SWI on the controller, then LED3 (learning code lamp) will light on, then press any key on the remote, if LED3 light on for 3 times, which means you add the remote successfully. If not, which means failed’

3.4 Erasing the transmitter codes:

please press button SW 1 on the controller about 10 seconds, during these 10 seconds, the LED3 will on firstly, then if the LED3 is off, which means you erase the remote successfully

3.5 Function for remote:

A.B.C.D., all buttons on the remotes has the function of open-pause-close. Each button ‘on the remote can work with one set of the gate opener.

4. Trouble Shooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>