KitchenAid W10706417B Side-By-Side Refrigerator Owner’s Manual

KitchenAid W10706417B Side-By-Side Refrigerator

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

•  Plug into a grounded 3-prong outlet.
•  Do not remove ground prong.
•  Do not use an adapter.
•  Do not use an extension cord.
•  Disconnect power before servicing.
•  Replace all parts and panels before operating.
•  Remove doors from your old refrigerator.
•  Use non-flammable cleaner.
•  Keep flammable materials and vapors, such as gasoline, away from refrigerator.
•  Use two or more people to move and install refrigerator.
• Disconnect power before installing ice maker (on ice maker kit-ready models only).
•  Use a sturdy glass when dispensing ice (on some models).
•  Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous, even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:

•  Take off the doors.
•  Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:
Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA-certified refrigerant technician in accordance with established procedures.

Tools and Parts

IMPORTANT:

•  Observe all governing codes and ordinances.
•  Installer: Leave Installation Instructions with homeowner.
•  Homeowner: Keep Installation Instructions for future reference and for the local electrical inspector’s use.
•  Keep cardboard shipping pieces or plywood under refrigerator until it is installed in the operating position.
•  Comply with installation specifications and dimensions.
•  Remove any moldings or decorative panels from kitchen cabinets that would not allow access to the refrigerator for service.
•  Contact a qualified electrical installer.

TOOLS NEEDED (on some models):

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

•  Cordless drill
•  ¹⁄₄” Nut driver and drill bit
•  Flat-blade screwdriver
•  ⁵⁄₁₆” or adjustable wrench
•  ⁷⁄₁₆” and ¹⁄₂” Open-end wrenches
•  Two adjustable wrenches
•  ³⁄₈” and ¹⁄₂” Socket wrenches

PARTS NEEDED (on some models):

•  Your refrigerator dealer has a kit available with a ¹⁄₄” (6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

•  Or you can purchase a ¹⁄₄” (6.35 mm) copper tubing with shutoff valve and a ¹⁄₄” (6.35 mm) compression fitting
  (coupling).

•  Depending on water line connections, you may also need a ¹⁄₄” (6.35 mm) nut and ¹⁄₄” (6.35 mm) ferrule.

Product Dimensions

Top View

maximum*

Curved| 28⁵⁄₈” (72.5 cm)| 2⁵⁄₈” (6.5 cm)| 31¹⁄₈” (79.1 cm)

Dimension may vary based on style of door handle. The depth for the largest available handle is listed.

Front View

Side View

•  Height dimensions are shown with the leveling legs extended to the minimum height of ¹⁄₄” (6.35 mm) below the refrigerator. NOTE: When leveling legs are fully extended to 1″ (25 mm) below the refrigerator, add ³⁄₄” (19 mm) to the height dimensions.
•  The power cord is 61¹⁄₄” (155.6 cm) long.
• The water line attached to the back of the refrigerator is 78″ (198.1 cm) long.

(180.2 cm)

Opening Dimensions

•  Height dimensions are shown with the leveling legs extended to the minimum height of ¹⁄₄” (6.35 mm) below the refrigerator. NOTE: When leveling legs are fully extended to 1″ (25 mm) below the refrigerator, add ³⁄₄” (19 mm) to the height dimensions.
•  In the following graphic, “A” represents the opening height required for standard cabinets. For full-overlay cabinet doors with a trim kit, add ¹⁄₈” (0.3 cm).
•  In the following graphic, “B” represents the distance needed to fully open the freezer door and “C” represents the distance needed to fully open the refrigerator door.

Model Size and

Door Style

| Height A| Width B| Width C
---|---|---|---
69″

Flat

| 69″

(175.3 cm)

| 13⁵⁄₈” (34.5 cm)

maximum*

| 18¹⁄₈” (46.0 cm)

maximum*

72″

Flat

| 72″

(182.9 cm)

| 13⁵⁄₈” (34.5 cm)

maximum*

| 18¹⁄₈” (46.0 cm)

maximum*

69″

Curved

| 69″

(175.3 cm)

| 13³⁄₄” (34.9 cm)| 18³⁄₈” (46.4 cm)
72″

Curved

| 72″

(182.9 cm)

| 13³⁄₄” (34.9 cm)| 18³⁄₈” (46.4 cm)

Dimension may vary based on style of door handle. The width for the largest available handle is listed.

Door Swing Dimensions

Dimension may vary based on style of door handle. The width for the largest available handle is listed. ****

Location Requirements

NOTES:

•  The refrigerator can be installed into a recessed opening, at the end of cabinets or as a freestanding refrigerator.
•  If you are installing the refrigerator to fit flush with the front of the base cabinets, all shoe molding and baseboards must be removed from the rear of the refrigerator opening. Allow for 1″ (2.54 cm) of space behind the refrigerator.
•  Location should permit doors to open fully. See “Product Dimensions.”
•  This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.
•  Floor must support refrigerator weight (more than 600 lbs [272 kg]) and contents.

Electrical Requirements

WARNING

• Plug into a grounded 3-prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation or cleaning, or removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See “Using the Controls” in the User Instructions, User Guide, or Use & Care Guide.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

•  Flat-blade screwdriver
•  ⁷⁄₁₆” and ¹⁄₂” open-end or two adjustable wrenches
•  ¹⁄₄” nut driver
•  ¹⁄₄” drill bit
•  Cordless drill

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄” (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆” (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

•  All installations must meet local plumbing code requirements.
•  Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

•  If your refrigerator has a water dispenser: After installation is complete, use the water dispenser to check the water pressure.
•  With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.
•  If it takes longer than 8 seconds to dispense 1 cup of water, the water pressure to the refrigerator is lower than recommended. See “Problem Solver” for suggestions.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa). If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

•  Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
•  Allow the storage tank on the reverse osmosis system to refill after heavy usage.
•  If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System” in the User Instructions, User Guide, or Use & Care Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING
Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injuries.

Remove the Packaging

Dispose of/recycle all packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.
IMPORTANT:

•  Use ¹⁄₂” socket wrench to remove skids (socket extension is recommended).
•  All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions.

Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Connect Water Supply

Read all directions before you begin.
IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.
• The gray water tubing on the back of the refrigerator (which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water. Check for leaks.
• If PEX tubing is used instead of copper, we recommend the following Whirlpool Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).
• Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:
Gather the required tools and parts before starting installation.

• Flat-blade screwdriver
• ⁷⁄₁₆” and ¹⁄₂” open-end wrenches or two adjustable wrenches
• ¹⁄₄” nut driver

Connect to Water Line

Style 1 (Recommended)

1.  Unplug refrigerator or disconnect power.

2.  Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.  Use a quarter-turn shutoff valve or the equivalent, served by a ¹⁄₂” copper household supply line.
   NOTE: To allow sufficient water flow to the refrigerator, a minimum ¹⁄₂” size copper household supply line is recommended.

4.  Now you are ready to connect the copper tubing to the shutoff valve. Use ¹⁄₄” (6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.

5. Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

6. Slip compression sleeve and compression nut onto copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

7.  Place the free end of the tubing into a container or sink, and turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.
   NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

8.  Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Style 2

1.  Unplug refrigerator or disconnect power.
2.  Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.
3.  Locate a ¹⁄₂” (1.27 cm) to 1¹⁄₄” (3.18 cm) vertical cold water pipe near the refrigerator.
4.  Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄” (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5.  Using a cordless drill, drill a ¹⁄₄” (6.35 mm) hole in the cold water pipe you have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄” (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1.  Unplug refrigerator or disconnect power.

2.  Remove and discard the short, black plastic part from the end of the water line inlet.

3.  Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
   NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

4.  Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

5.  Turn shutoff valve ON.

6.  Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 2

1.  Unplug refrigerator or disconnect power.
2.  Remove and discard the plastic part that is attached to the inlet of the water valve.
3.  Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.
4.  Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.
5.  Turn shutoff valve ON.
6.  Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.
7.  On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄” (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 3

1.  Unplug refrigerator or disconnect power.

2.  Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.  If the gray water tube supplied with the refrigerator is not long enough, a ¹⁄₄” x ¹⁄₄” (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.
   NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

4.  Turn shutoff valve ON.

5.  Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

1.  Plug into a grounded 3-prong outlet.

2.  Wait a few minutes. Check that the compressor is operating properly and that all lights are working.
   NOTE: If the refrigerator does not operate, check that the circuit breaker is not tripped or that the household fuse has not blown.

3.  Flush the water system. See “Water and Ice Dispensers” in the User Instructions or User Guide.
   NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to completely fill ice container.

Leveling and Door Closing

Your refrigerator has two adjustable front feet — one on the right and one on the left. In most cases, the refrigerator should be steady when both feet are touching the floor. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator’s tilt using the instructions below:

1.  Move the refrigerator into its final location. Open both doors to 90°. Remove the base grille by removing the two screws, then pulling out on the outside corners.

2.  The two leveling feet are located on the brackets on each side of the product.

3.  Use a ¹⁄₄” open-ended or adjustable wrench to adjust the leveling feet. Turn the leveling foot to the left to raise that side of the product, or turn it to the right to lower that side of the product.
   NOTE: Both leveling feet should be snug against the floor, and the rollers should not touch the floor. This keeps the refrigerator from rolling forward when opening the doors.

4.  Open both doors again and check that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning the leveling feet to the left. It may take several more turns, and you should turn both leveling feet the same amount.

5.  Use a bubble level to check the leveling of the refrigerator.
   NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side to side may appear to have doors that are not properly aligned. If the doors appear this way, use the instructions in the previous section to check the leveling. The doors are designed to be slightly different heights when the refrigerator is empty, in order to account for the weight of food that will be placed on the doors. If the doors are still not aligned after checking the leveling and loading the refrigerator with food, follow the steps below to adjust the door alignment.

1.  If necessary, open both doors to 90° and remove the base grille.
2.  Locate the alignment screw on the bottom hinge of the refrigerator door.
3.  Use a ⁵⁄₁₆” open-ended or adjustable wrench to turn the screw. To raise the refrigerator door, turn the screw to the right. To lower the door, turn the screw to the left.
4.  Check that the doors are even at the top. If necessary, continue to turn the alignment screw until the doors are aligned.
5.  Open both doors to 90°. Replace the base grille.

Install Air Filter

On some models, your refrigerator’s accessory packet includes an air filter, which must be installed prior to use. On some models, the air filter is already installed at the factory. The air filter reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator.

Installing the Air Filter (on some models)

The filter should be installed behind the vented door, which is located (depending on your model) along either the rear or left interior wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.
2. Lift open the vented door.
3. Snap the filter into place.
4. Close the vented door.

Installing the Filter Status Indicator (on some models)

The filter comes with a status indicator, which should be activated and installed at the same time the air filter is installed.

1.  Place the indicator face-down on a firm, flat surface.

2.  Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.

3.  Lift open the vented air filter door. On some models, there are notches behind the door.

4.   On models with notches:
   Slide the indicator down into the notches, facing outward.
   NOTE: The indicator will not easily slide into the notches if the rear bubble has not been popped.
   Close the air filter door, and check that the indicator is visible through the rectangular hole in the door.

5. On models without notches:
   Store the indicator in a visible place you will easily remember – either inside the refrigerator or elsewhere in your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months when the status indicator has completely changed from white to red. To order a replacement air filter, see “Accessories” in the User Instructions or User Guide.

1.  Remove the old air filter by squeezing in on the side tabs.
2.  Remove the old status indicator.
3.  Install the new air filter and status indicator using the instructions in the previous sections.

Install Produce Preserver

On some models, your refrigerator’s accessory packet includes a Produce Preserver, which should be installed prior to use. On some models, the Produce Preserver is already installed at the factory. The Produce Preserver absorbs ethylene, allowing the ripening process of many produce items to slow down. As a result, certain produce items will stay fresh longer. Ethylene production and sensitivity varies depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate to high amounts of ethylene.

| Sensitivity to Ethylene| Ethylene Production
---|---|---
Apples| High| Very High
Asparagus| Med.| Very Low
Berries| Low| Low
Broccoli| High| Very Low
Cantaloupe| Med.| High
Carrots| Low| Very Low
Citrus Fruit| Med.| Very Low
Grapes| Low| Very Low
Lettuce| High| Very Low
Pears| High| Very High
Spinach| High| Very Low

Installing the Produce Preserver (on some models)

The Produce Preserver pouches should be installed in their housing, which is located along an interior side wall of the crisper or convertible drawer.
NOTE: For best performance, always use two pouches.

1.  Remove the Produce Preserver pouches from their packaging.
2.  Lift up on the housing in order to remove it from its mounting tab along the wall.
3.  Open the housing by pulling up and out on the back of the top of the housing.
4.  Place both pouches inside the housing, then snap the housing back together.
5.  Place the housing back on the mounting tab along the wall.

Installing the Status Indicator (on some models)

The Produce Preserver comes with a status indicator, which should be activated and installed at the same time the pouch is installed.

1.  Place the indicator face-down on a firm, flat surface.
2.  Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.
3.  Slide open the cap on the Produce Preserver housing.
4.  Place the indicator in the top of the housing, facing outward.
5. 5. Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.
   NOTE: The cap will not easily close if the indicator’s rear bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months when the status indicator has completely changed from white to red. To order replacements, see “Accessories” in the User Instructions or User Guide.

1.  Remove the old pouches from the Produce Preserver housing.
2.  Remove the old status indicator.
3.  Install the new pouches and status indicators using the instructions in the previous sections.

Changing the Water Filter

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. The water filter status light will help you know when to change your water filter. See “Water Filtration System” in the User Instructions or User Guide.
NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months, depending on your water quality and usage.

1.  Locate the water filter in the top-right corner of the refrigerator compartment.

2.  Lift open the filter cover door. The filter will be released and then be ejected as the door is opened.

3.  When the door is completely open, pull the filter straight out.
   NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.

4.  Take the new filter out of its packaging and remove the cap. Be sure the O-rings are still in place after the cap is removed.

5.  With the arrow pointing up, align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.

6.  Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

7.  After changing the filter, reset the filter status light. See “Water Filtration System” in the User Instructions or User Guide.

8.  Flush the water system. See “Water and Ice Dispensers” in the User Instructions or User Guide.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1.  Unplug refrigerator or disconnect power.
2.  Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
3.  Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.
4.  There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency. If you need to clean the condenser:
5. Remove the base grille. See the “Door Removal” instructions, either in the User Instructions or the Installation Instructions and Owner’s Manual, or in the separate instruction sheet provided with your refrigerator.
6. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.
7. Replace the base grille when finished.
8.  Plug in refrigerator or reconnect power.

Lights

IMPORTANT: The refrigerator and freezer compartments, air tower and dispenser lights are LEDs that cannot be changed by yourself. To order replacement LED lightings, call Whirlpool service. In the U.S.A., call 1-800-253-1301. In Canada,
call 1-800-807-6777.
Light Styles:
The dispenser lights are mini LEDs that cannot be changed. The interior lights vary by model.

• Some models have mini LEDs that cannot be changed.

• Some models have full-size LED bulbs that can be changed. To order replacement LED bulbs, call 1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).
  NOTE: Some LED replacement bulbs are not recommended for wet/damp environments. The refrigerator and freezer compartments are considered to be wet/damp environments. If using a brand of LED bulb other than the recommended Whirlpool LED bulb, read and follow all instructions on the replacement bulb’s packaging before installing it.

• Some models have incandescent 40-watt bulbs that can be changed.
  NOTE: Not all replacement bulbs will fit your refrigerator. Do not use an incandescent bulb in excess of 40 watts.

To Change a Light Bulb:

1.  Unplug refrigerator or disconnect power.

2.  Remove the light shield as explained in the following sections.
   NOTE: To clean the light shield, wash it with warm water and liquid detergent. Before reinstalling, thoroughly rinse and dry the shield.

3.  Replace the burned-out light bulb, as explained in the following sections.

4.  Reinstall the light shield, as explained in the following sections.

5.  Plug in refrigerator or reconnect power.

Refrigerator Compartment – Upper Lights

Light Shield Removal:

Slide the light shield toward the rear of the refrigerator and remove it from the light housing.

Replacement Bulb:

• If the burned-out light is a full-size LED bulb, replace it with Whirlpool part number W10574850A (a 2.0-watt LED bulb).
• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

Align the light shield in the grooves at the bottom edge of the light housing, then slide it forward until it snaps into place.

Refrigerator Compartment – Lower Lights

Light Shield Removal:

Slide the light shield to the right to remove the left end from the wall slots; then, pull the right end out of its wall slots.

Replacement Bulb:

• If the burned-out light is a full-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).
• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

Place the right end of the light shield into the wall slots, then snap the left end into its wall slots.

Freezer Compartment – Upper Light

Light Shield Removal:

Gently squeeze the front and the bottom-rear edge of the light shield to release the tabs from the wall slots, then pull the light shield forward.

Replacement Bulb:

• If the burned-out light is a full-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).
• If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

Align the light shield in its proper position, and snap the tabs into the wall slots.

Freezer Compartment – Lower Light

Light Shield Removal:

Slide the light shield to the left to remove the right end from the wall slots, then pull the left end out of its wall slots.

Replacement Bulb:

•  If the burned-out light is a full-size LED bulb, replace it with Whirlpool part number W10565137A (a 3.6 watt LED bulb).
•  If the burned-out light is an incandescent bulb, replace it with an incandescent appliance bulb of the same size, shape and wattage (40-watt maximum).

Light Shield Reinstallation:

Place the left end of the light shield into the wall slots, then snap the right end into its wall slots.

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1.  Use up any perishables and freeze other items.
2.  If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.
3.  If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm to OFF (up) position or press the switch to OFF (right).
4.  Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1.  Remove all food from the refrigerator.
2.  If your refrigerator has an automatic ice maker:
3. Turn off the water supply to the ice maker at least one day ahead of time.
4. When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
5.  Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See “Using the Controls” in the User Instructions, User Guide, or Use & Care Guide.
6.  Clean, wipe, and dry thoroughly.
7.  Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1.  If your refrigerator has an automatic ice maker:
2.  Turn off the water supply to the ice maker at least one day ahead of time.
3.  Disconnect the water line from the back of the refrigerator.
4.  When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
5.  Remove all food from the refrigerator and pack all frozen food in dry ice.
6.  Empty the ice bin.
7.  Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See “Using the Controls” in the User Instructions, User Guide, or Use & Care Guide.
8.  Unplug refrigerator.
9.  Clean, wipe, and dry thoroughly.
10.  Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle during the move.
11.  Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don’t scrape the floor. See “Adjust the Doors” or “Door Removal, Leveling and Alignment.”
12.  Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the Installation Instructions for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

PROBLEM SOLVER

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

PERFORMANCE DATA SHEET

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

•  It is important that operational, maintenance and filter replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed.

•  Use replacement filter P4RFWB, part #W10295370A. 2014 suggested retail price of $39.99 U.S.A./$49.99 Canada. Prices are subject to change without notice.
  Style 1 – When the water filter status display changes from “GOOD” to “ORDER,” order a new filter. When the filter indicator reads “REPLACE,” it is recommended that you replace the filter.
  Style 2 – When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter.
  Style 3 – When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that you replace the filter.
  Style 4 – Press FILTER to check the status of your water filter. If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the filter.

•  After changing the water filter, flush the water system. See “Water and Ice Dispensers” or “Water Dispenser” in the User Instructions or User Guide.

•  These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

•  The product is for cold water use only.

•  The water system must be installed in compliance with state and local laws and regulations.

•  Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

•  Refer to the “Warranty” section (in the User Instructions or User Guide) for the Manufacturer’s name, address and telephone number.

•  Refer to the “Warranty” section (in the User Instructions or User Guide) for the Manufacturer’s limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply  City or Well
Water Pressure  30 – 120 psi (207 – 827 kPa)
Water Temperature  33° – 100°F (0.6° – 37.8°C)
Service Flow Rate  0.5 GPM (1.9 Lpm) @ 60 psi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>