A TIBAL SAP 1x Micro Prism Owner’s Manual

A TIBAL SAP 1x Micro Prism

PRODUCT OVERVIEW

The Atibal S.A.P. Micro Prism is the smallest and lightest prismatic scope on the market to date. This prism is perfect for red dot lovers everywhere, especially if your red dot always looks like a starburst. The laser etched prismatic reticle of the S.A.P. ensures a crisp and clear reticle every time, regard-less of the user’s vision. The S.A.P. also features a reticle focus adjust at the ocular lens to further ensure a perfectly focused reticle every time.

1. On/ Off, Dot Brightness Adjust.
2. Battery Compartment.
3. Elevation Adjustment Dial.
4. Windage Adjustment Dial.
5. Removable Rail Mount.
6.  Objective Lens.
7.  Reticle Focus Adjust.

SPECIFICATIONS

OPERATING INSTRUCTIONS

INSTALLING THE BATTERY
The battery compartment is located on the right side of the optic, you DO NOT need to dismount the optic in order to change the battery. To install/ replace the battery simply loosen the torx head screws and slide the battery tray out. Insert one (1) CR2032 battery into compartment, positive side facing upwards, re-insert the battery tray and handtighten the hardware, do not overtighten. Be careful to not lose the tray hardware or damage the battery tray.

POWER ON/OFF
To power on the optic simply press the up arrow of the brightness adjustment buttons located on the left side of the optic. To shut the optic off press and hold the down arrow of the brightness adjust buttons for 3 seconds. The SAP features a 4 hour Auto Shut-Off to preserve battery life.

BRIGHTNESS SETTINGS

The Atibal SAP Micro Prism features 8 different brightness settings. Brightness settings can be adjusted by pressing the “^” or “v” buttons located on the left side of the optic. The SAP reticle is laser etched, so even with the illumination turned off the reticle will always be visable.

MOUNTING THE Atibal SAP Micro Prism

The Atibal SAP Micro Prism has a short eye relief and can be mounted directly to any Picatinny rail. The Atibal SAP Micro Prism comes with a removable Co- Witness Height rail mount. The ACW rail mount can be removed and replaced with an low profile mount or a lower 1/3 height mount, additional mounts are sold seperately.

MOUNTING THE Atibal SAP Micro Prism

To mount the Atibal SAP Micro Prism simply place in the desired position on the rail and tighten the mounting screw located on the side of the rail mount. When properly installed the device should sit flush with the top of the rail and be tightened down adequately so as not to come loose while in use or in storage. Atibal recommends mounting the Atibal SAP Micro Prism as close to the shooter as possible due to the short eye relief of the SAP Micro Prism.

ELEVATION AND WINDAGE ADJUSTMENTS

It is recommended that you bore sight your optic prior to zeroing your Atibal SAP Micro Prism; while boresighting isn’t guaranteed to give you a perfect zero it should get you close enough to easily determine the corrections needed to zero the optic.

ELEVATION AND WINDAGE ADJ. CONTD

The Tribal SAP Micro Prism has 1 MOA click adjustment, 1 MOA = 1.05” @ 100 yards or 1/10” @ 10yards. At a short distance of 20 to 25 yards try to group at least three shots as close to center target as possible. Use the center of this group as a reference to determine the necessary corrections to the red dot. Remove the elevation and windage caps from the optic. Using a standard screwdriver make adjustments to the windage and elevation dials in the appropriate direction to move the strike of the round closer to the center of your target. Rotating the windage and elevation dials in a clockwise direction will move the strike of the round up in elevation and right in windage. Once a satisfactory short range zero has been achieved move the target to a further distance and repeat the process until a desirable zero has been achieved.

MOUNTING THE Atibal SAP Micro Prism:

To mount the Atibal SAP Micro Prism simply place in the desired position on the rail and tighten the mounting screw located on the side of the rail mount. When properly installed the device should sit flush with the top of the rail and be tightened down adequately so as not to come loose while in use or in storage. Tribal recommends mounting the Atibal SAP Micro Prism as close to the shooter as possible due to the short eye relief of the SAP Micro Prism.

ELEVATION AND WINDAGE ADJUSTMENTS

It is recommended that you bore sight your optic prior to zeroing your Atibal SAP Micro Prism; while boresighting isn’t guaranteed to give you a perfect zero it should get you close enough to easily determine the corrections needed to zero the optic.

ELEVATION AND WINDAGE ADJ. CONTD

The Tribal SAP Micro Prism has 1 MOA click adjustment, 1 MOA = 1.05” @ 100 yards or 1/10” @ 10yards. At a short distance of 20 to 25 yards try to group at least three shots as close to center target as possible. Use the center of this group as a reference to determine the necessary corrections to the red dot. Remove the elevation and windage caps from the optic. Using a standard screwdriver make adjustments to the windage and elevation dials in the appropriate direction to move the strike of the round closer to the center of your target. Rotating the windage and elevation dials in a clockwise direction will move the strike of the round up in elevation and right in windage. Once a satisfactory short range zero has been achieved move the target to a further distance and repeat the process until a desirable zero has been achieved.

CLEANING

Be sure to use only Multi-Coated Lens-specific cleaning products when choosing cleaning products for this optic. Clean both the lenses of all debris prior to wiping the lenses clean with the provided cleaning rag. Use water or multi- coated lens-specific cleaning products to clean the lenses of any build-up or grime. To avoid scratching the lenses, never wipe the lenses when any debris is present on the lens itself. When cleaning the body of the Atibal SAP Micro Prism use a cleaning brush and firearm-specific cleaning product, always being mindful of the lenses. During the routine, firearm maintenance checks the mounting hardware to ensure that all parts are securely fastened and make adjustments as needed.

TROUBLESHOOTING

If the Tribal SAP Micro Prism fails to operate properly you should inspect the battery to ensure it is installed correctly and is not low on power. If replacing the battery does not solve the problem please contact us at info@atibalsights.com for further assistance.

WARRANTY

No gimmicky names or slogans to make our Lifetime Warranty sound better than what it is. At Atibal we call our Lifetime Warranty a Lifetime Warranty. If your Atibal product becomes defective, broken, no longer working we will get it  For warranty information visit atibaloptics.com The Atibal Lifetime Warranty does not cover loss, theft, battery leakage, deliberate damage or cosmetic damage that does not hinder the performance of the product.

References

• ATIBAL SIGHTS, LLC. PREMIUM QUALITY SCOPES & RED DOTS – Atibal Optics

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>