Huddly L1 AI Collaboration Camera Instruction Manual

: June 5, 2024
: Huddly

Table of Contents

Safety and Caution Information
User Instructions
Regulatory Compliance Information
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

L1 AI Collaboration Camera
Instruction Manual

Safety and Caution Information

Temperature
This device is intended for use in ambient temperatures between 0 °C and 35 °C (32 °F and 95 °F). Avoid using or storing next to heat sources, in direct sunlight, or outside the intended temperature ranges.
Modify
Modification to the thermal solution, device components, or enclosure shall violate regulatory compliance requirements and may induce safety hazards.

User Instructions

The L1 camera is made for easy installation, using only a single RJ45 Ethernet cable for both power and communications with a host computer.

Installation
Use the ¼” tripod mount found on the bottom face of the camera to attach a bracket to the L1. Using the bracket, mount the L1 at a maximum height of 2m.
The L1 must be installed in a location where the top and bottom venting holes are unobstructed, to ensure proper airflow.
Connect minimum a Cat5e rated Ethernet cable to the camera, and terminate the cable in a Power over Ethernet (PoE) Power Sourcing Equipment (PSE) enabled host or midspan adapter.
If third-party Ethernet cables are to be used, then prioritize Ethernet cables with short connectors. The long connector alternatives can be more difficult to disconnect.
Make sure to use the latest camera software by following the instructions at: www.huddly.com/L1/setup

Power
The L1 cameras can be powered by a PoE PSE which adheres to the following minimum requirements:

Voltage range: 37-57V DC
Maximum current: 0.35A

Streaming
The L1 support streaming over the Real-Time Streaming Protocol (RTSP) and Open Network Video
Interface Forum (ONVIF).

Factory reset
To reset the L1 to factory default, use the following procedure:

Disconnect the Ethernet cable from the camera
Use a thin object to press the reset button through the hole located in the top left corner of the connector cavity
Keep the button pressed while reinserting the Ethernet cable
After power has been reapplied to the camera, keep the reset button pressed for 10 seconds
The camera will now reset to factory settings

Recycling
At the end of life for this product, local rules and regulations shall be followed. This product is ment to be recycled, and if applicable and/or possible, should be handed in to a collection point for recycling purposes.

Regulatory Compliance Information

This product is cNus marked in accordance with the requirements of the applicable standards for Canada and the United States.

Canada
Industry Canada statement
This Class A digital apparatus complies with CAN ICES-3 (A)/NMB-3(A).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

United States
FCC compliance statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Australia and New Zealand

This product is C-Tick marked in accordance with the requirements of the applicable Australian and New Zealand standards.
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

European Union
EU Single Point of Contact
Huddly AS,
Attn: Compliance
Karenslyst allé 51
0279 Oslo, Norway

European Union EMC Directive conformance statement
This product has been tested and found to comply with the limits for Class A equipment according to European Standards harmonized in the Directives in compliance. The limits for Class Equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.
Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

In the European Union, this symbol indicates that this product must not be disposed of with household waste. It is your responsibility to hand it over to a designated collection point for the recycling of waste electronic equipment. For more information, please contact your local waste collection center or the point of purchase of this product.

Support

For more information visit: www.huddly.com/support

EULA
By using this product, you agree that your use of this product is subject to our End User Licence Agreement terms available at: www.huddly.com/eula

Privacy policy
Our privacy policy is available at: www.huddly.com/privacy- policy
You can find further compliance information at: www.huddly.com/L1/compliance