LiftMaster STAR1000 Commercial Access Control Receiver Instruction Manual
- June 5, 2024
- LiftMaster
Table of Contents
STAR1000 Commercial Access Control Receiver
LiftMaster
APPLICATION The STAR1000 is a high capacity single channel commercial access control receiver for commercial door operators, and dry contact triggered devices. The STAR1000 is compatible with Security+ 2.0TM remote controls and wireless keyless entries, Security+ 2.0T Passport and Passport Lite remote controls. This receiver is compatible with HomeLink®. For programming or compatibility information visit www.homelink.com. The receiver capacity is 1,000 devices and can be any combination of remote controls and wireless keyless entries. The receiver is watertight according to IPX44 specification.
INSTALLATION
-
Select a convenient location near the operator to be controlled by the receiver within “line of sight” of the intended transmitting location.
NOTE: Do not mount LCD screen in direct sunlight. Avoid mounting the receiver in a metal enclosure or near other wireless receiving or transmitting devices. -
Mount the bracket to the desired surface with appropriate hardware (not provided) (Figure 1).
-
Remove the 4 (#8) screws on the back of the receiver and remove the faceplate. Unplug the keypad connector from the control board. NOTE: Be careful not to damage the keypad cable while removing the faceplate.
-
Make wiring connections (Figure 2). Refer to your gate or commercial door operator owner‘s manual for more specific information.
-
Reconnect the keypad connector to the board (labeled J9).
-
Secure the faceplate with the 4 (#8) screws previously removed.
-
Install the antenna provided.
NOTE: Use the optional 86LM or 86LMT antenna extension kit (see page 4) to mount the remote antenna as high and far from metallic objects as possible for best radio range. -
Snap the receiver onto the mounting bracket and secure with the (#8) screws provided.
-
Tighten the watertight connector to secure and seal the wiring.
COMMERCIAL ACCESS CONTROL RECEIVER
MODEL STAR1000
WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution:
- Be sure power is NOT connected BEFORE installing the receiver. To prevent possible SERIOUSINJURY or DEATH from a moving gate or garage door:
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
- Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
- ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
WARNING
To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. When a receiver is used to activate a commercial door opener, a reversing edge MUST be installed on the bottom of the door. Failure to install a reversing edge under these circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
USER INTERFACE
The STAR1000 user interface consists of a 22 character by 5 line LCD display, 3 “soft keys“, Down/Up arrows and a numeric keypad.
PROGRAMMING
The receiver has the ability to learn a combination of remote control transmitters and keyless entries up to 1,000 devices. See page 4 for a complete list of compatible accessories. Audible and visual warnings occur when the receiver capacity is exceeded. After 30 seconds of inactivity, the receiver times out and the LiftMaster® logo is displayed. Select “UNLOCK” and enter the PIN to continue. Initial PIN set up: The PIN restricts access to authorized administrators only. If you omit this step, anyone will be able to program the receiver. Upon initial power up, the system firmware revision is displayed for 5 seconds followed by the LiftMaster® logo. When a key is pressed, “CREATE PIN?” is displayed.
- Press “YES” to create PIN. If the PIN is lost you may request a reset code by pressing “RESET”.
- Enter a 6-digit PIN, and press “YES”; enter the 6-digit PIN a second time and press “YES” to program the PIN. If you make a mistake, press “CLEAR” to change your entry. To exit the enter PIN screen, select “BACK”.
- When your 6-digit PIN is programmed correctly, the LCD display reads “KEYPAD UNLOCKED”. Select “OK” to continue to the Main Menu. After 30 seconds of inactivity, the receiver times out and the LiftMaster® logo is displayed. Select “UNLOCK” and enter PIN to continue.
PROGRAMMING COMMANDS
DIAGNOSTICS
The receiver emits a series of audible beeps to signal programming and error events. The table at right lists all of the events and their audible notifications. The On/Off column indicates that the audible notification for the event may be disabled in the BEEP SETTINGS menu.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800–528–2806
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>