evolar EVO-CF52BWD Ceiling Fan Instruction Manual

EVO-CF52BWD Ceiling Fan
Instruction Manual

SAFETY TIPS

WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories.
READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.

1. Make sure all electrical connections comply with Local Codes or Ordinances, the National Electrical Code. If you are unfamiliar with electrical wiring or if the house/building wires are different colors than those referred to in the instruction please use a qualified electrician.

2. Make sure you have a location selected for your fan that allows clear space for the blades to rotate and at least seven (7) feet (2.3 meters) of clearance between the floor and the fan blade tips. The fan should be mounted so that the tips of the blades are at least thirty (30) inches (76 centimeters) from walls or other upright structures.

3. The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 Pounds (45.4 kilograms). The outlet box must be supported directly by the building structure. Make sure the electrical box that will hold the ceiling fan is fan-rated. There should be an inscription on the box indicating it.
   WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to the outlet box marked “Acceptable for Fan Support, ” and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
   Consult a qualified electrician if in doubt.

4. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on opposite sides of the outlet box.
   WARNING: To reduce the risk of electrical shock, and fire and to prevent humming noise do not use this fan with any solid-state speed control device or control fan speed with a  full range dimmer switch. Using a full-range dimmer switch to control fan speed will cause a loud humming noise from the fan.

5. Do not operate the reverse switch until fan has come to a complete stop.(If included Forward/Reverse Switch)

6. Do not insert anything between the fan blades while they are rotating.
   WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
   WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.

7. Do not use water or detergents when cleaning the fan or fan blades. Dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
   WARNING: To reduce the risk of personal injury, use only parts provided with this fan.
   The use of parts OTHER than those provided with this fan will void the warranty.

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense and caution are necessary factors in the installation and operation of this fan.

Preparing for installation

Package Lists

Remote control unit

Installing the ceiling fan

Step 1(Down rod and motor assembling)

Step 2 (Ceiling bracket and fan body installation )

Step 3 (Put receiver into ceiling bracket and wiring)

Step 4 ( Blades and Light kit installation)

Step 5(Switch on and ceiling fan works)

Remote control (emitter) operation

If the emitter can not control the fan

1. Please check whether the battery is installed correctly and whether it is charged. If necessary, replace the remote control battery.
2. Please check if there are similar remote control products working nearby because remote control products of the same frequency will interfere with each other.
3. Use learning code matching mode is used between the emitter and receiver Turn “ON”the supply power within 30 seconds and press the emitter,’s “ ” button for 5 seconds. it can load normally after hearing the long sound”bee”, which means learning successfully and it can works normally- ly.

Troubleshooting

Fan does not work

1. Check all fuses or circuit breakers if disconnecting the power supply to the fan.
2. Turn off the electrical power and check all wire connections to the fan and in the switch housing. It must be carried out by an electrician

Fan is noisy

1. Assure that the screws fastening the blade arm to the motor is tight and the lock washers provided for that purpose have been used
2. Lower the upper canopy to ensure separation from the ceiling of no less than 3mm to reduce noisily
3. Check to see if any of the blades are cracked. If so, replace all of the blades
4. If this is the first use, leave the fan on for at least 8 hours. In the event that mechanical noise continues after this period, contact a certified electrician

Fan turns but airflow is inadequate

1. The fan may be running in reverse, so air is going upward.
2. The room may contain items that obstruct the airflow.
3. The fan may be too small for the size of the room.

Fan shakes or wobbles

1. The fan blades are not parallel to the ceiling. See Fig.1 for how to inspect
2. Make sure the mounting bracket is tightened at the outlet box with no movement at all.
3. Make sure all screws holding the blades to the blade arm and blade arm to the motor are tight.
4. Use the balance kit and instructions to balance the fan. Please see the last pages described.

Balancing – Wobbling problems during fan operation

If the fan body wobbles during its operation, this is not a sign of malfunctioning (even if it wobbles a few centimeters). To reduce wobbling, you can, while the fan is off:

1. Check that all blades are properly fastened by tightening their screws.
2. Check the distance between each blade and the ceiling. Measurements to the ceiling can be carried out as shown in the following diagram. If variations exist and you have already correctly tightened the screws, check that all blades have the same shape. If any of them have a shape that is visibly different, this may be causing an imbalance during fan operation.
   

If you have completed the previous steps and the wobbling has not resolved, you should apply dynamic balancing with the kit provided, as explained below:

1. Turn the fan on to the highest speed so that the greatest amount of wobbling is produced.

2. Turn off the fan. Select a blade and place a clip on it (see diagram) halfway between the fastening and the far edge of the blade.

3. Turn on the fan and check whether the wobbling has improved or gotten worse.
   Turn it off once again and if the wobbling has not improved, place the clip on another blade. Repeat this process and determine on which blade it improves the wobbling.

4. Leave the clip on the blade that produces the best results. Move the clip forward or backward on this blade until finding the position that offers the best results.

5. Afterward, remove the clip and place one of the weights on the upper part of the centerline of the blade at the position where the clip was located.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>