BLACK DECKER BEHT201 45cm 420W Hedge Trimmer Instruction Manual

: June 5, 2024
: Black Decker

Table of Contents

Safety instructions
Additional power tool safety warnings
Electrical safety
Features
Use
Accessories
Maintenance
Protecting the environment
Technical data
Guarantee
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEHT201
BEHT251
www.blackanddecker.eu

(Original instructions)

Intended use
Your BLACK+DECKER™ BEHT201, BEHT251 hedgetrimmers have been designed for trimming hedges, shrubs, and brambles. These tools are intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire, and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
a. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service
a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for hedge trimmers

Keep all parts of the body away from the cutter blade. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. A moment of inattention while operating the tool can result in serious personal injury.
Carry the hedge trimmer by the handle with the cutter blade stopped. When transporting or storing the hedge trimmer always fit the cutting device cover. Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades.
Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring or its own cord. Cutter blades contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Keep the cable away from the cutting area. During operation, the cable can be hidden in shrubs and can accidentally cut the blades.
The intended use is described in this instruction manual. The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual can present a risk of personal injury and/or damage to property.
If you have not used a hedge trimmer before, preferably seek practical instruction by an experienced user in addition to studying this manual.
Never touch the blades while the tool is running.
Never attempt to force the blades to come to a standstill.
Do not put the tool down until the blades have come to a complete standstill.
Regularly check the blades for damage and wear. Do not use the tool when the blades are damaged.
Take care to avoid hard objects (e.g. metal wire, railings) when trimming. Should you accidentally hit any such object, immediately switch the tool off and check for any damage?
Should the tool start to vibrate abnormally, immediately switch it off and disconnect it from the mains suply then check for any damage.
If the tool stalls, immediately switch it off. Disconnect it from the mains supply before attempting to remove any obstructions.
After use, place the blade sheath supplied over the blades. Store the tool, making sure that the blade is not exposed.
Always ensure that all guards are fitted when using the tool.
Never attempt to use an incomplete tool or a tool with unauthorized modifications.
Never allow children to use the tool.
Be aware of falling debris when cutting the higher sides of a hedge.
Always hold the tool with both hands and by the handles provided.

Residual risks
Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

Injuries caused by touching any rotating/moving parts.
Injuries are caused when changing any parts, blades, or accessories.
Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech, and MDF.)

Vibration
The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated.
When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the date code:

**| Warning! To reduce the risk of injury, the user must read the instruction manual.
---|---
**| Wear safety glasses or goggles when operating this tool.
****| Wear ear protection when operating this tool.
| Immediately disconnect the cable from the mains if it is damaged or cut.
| Do not expose the tool to rain or high humidity.
| Directive 2000/14/EC guaranteed sound power.

Electrical safety

**** This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

If the supply cord is damaged, it must be replaced by the manufacturer or an authorized BLACK+DECKER Service Centre in order to avoid a hazard.
When using the tool outdoors, only use extension cables intended for outdoor use. A suitable rated BLACK+DECKER extension cable of up to 30 m can be used without loss of power.
Electric safety can be further improved by using a high sensitivity 30 mA residual current device (RCD).

Features

This tool includes some or all of the following features.

Blade
Guard
Auxiliary handle
Lock off button
Trigger switch
Switch handle
Cord retainer

Assembly
Warning! Before assembly, make sure that the tool is switched off and unplugged and that the blade sheath is fitted over the blades.

Attaching guard to trimmer (fig. A, B)
The trimmer is shipped with the guard unattached to the trimmer. To attach the guard:

Remove guard retaining screw 10 with a Phillips screwdriver (not supplied).
Position the guard in place as shown in Fig. A. Ensuring the guard slots into the grooves on the unit.
Insert the guard retaining screw 10 into the opening on the side of the guard and tighten securely as shown in Fig. B.
Warning! Only use with handle and guard properly assembled to hedge trimmer. The use of the hedge trimmer without the proper guard or handle provided may result in serious personal injury.

Attaching extension cord to trimmer (fig. C)
A cord retainer (7) is incorporated into the rear of the switch handle (6).

Near the end of the extension cord, fold the extension cord to create a loop.
Feed the loop into the cord retainer housing 11 as shown in Fig. C.
Hook the loop onto the cord retainer 7 so it rests in the cord retainer.
Plug the extension cord into the unit.

Correct hand position (Fig. D)
Always hold the trimmer, as shown in the illustrations in this manual, with one hand on the switch handle and one hand on the auxiliary handle (Fig. D). Never hold the unit by the blade guard.

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off
Note: For your safety, this tool is equipped with a double switching system. This system prevents starting the tool inadvertently and will only allow operation while holding the
a tool with both hands.

Switching on (fig. E)

To turn the tool “ON”, press the lock-off button (4) in the auxiliary handle (3) backward and squeeze the trigger switch (5). Once the unit is running, you may release the
lock-off button. In order to keep the unit running, you must continue to squeeze the trigger. To turn the tool “OFF”, release the trigger.
Warning! Never attempt to lock a switch in the ON position.
Regularly oil the blades.

Guidelines for trimming

Extension cord (fig. F)

Always keep the extension cord behind the trimmer and away from the trimming operation as shown in figure F. Never drape it over a hedge being trimmed.
If you cut or damage the cord, unplug it at the electrical outlet immediately, before inspecting or repairing the cord.

Working position

Maintain proper footing and balance and do not overreach.
Wear safety goggles, non-skid footwear, and rubber gloves when trimming.
Hold the tool firmly in both hands and turn the tool ON. Always hold the trimmer, as shown in Fig. D, with one hand on the switch handle and one hand on the auxiliary
handle. Never hold the tool by the blade guard.

Trimming new growth (fig.G)

A wide, sweeping motion, feeding the blade teeth through the twigs is most effective. A slight downward tilt of the blade, in the direction of motion, gives the best cutting.

Warning! Do not use the trimmer for cutting stems greater than 16 mm. Use the trimmer only for cutting normal shrubbery found around houses and buildings.
Level hedges (fig.H)

To obtain exceptionally level hedges, a piece of string can be stretched along the length of the hedge as a guide.

Side trimming hedges (fig.I)

Begin at the bottom and sweep up.

The cutting blades are made from high-quality, hardened steel, and with normal usage, they will not require resharpening. However, if you accidentally hit a wire fence (Fig. J), stones, glass, or other hard objects, you may put a nick in the blade. There is no need to remove this nick as long as it does not interfere with the movement of the blade. If it does interfere, unplug the cord and use a fine-toothed file or sharpening stone to remove the nick. If you drop the trimmer, carefully inspect it for damage. If the blade is bent, housing cracked, or handles broken, or if you see any other condition that may affect the trimmer’s operation contact your local BLACK+DECKER Service Center for repairs before putting it back into use. Fertilizers and other garden chemicals contain agents which greatly accelerate the corrosion of metals. Do not store the unit on or adjacent to fertilizers or chemicals.

Accessories

The performance of your tool depends on the accessory used. BLACK+DECKER accessories are engineered to high-quality standards and designed to enhance the performance of your tool. By using these accessories you will get the very best from your tool.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Lubrication oil is available from your BLACK+DECKER dealer (cat. no. A6102-XJ).

Warning! Before performing any maintenance on corded/cordless power tools:

Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then switch off.
Unplug the charger before cleaning it. Your charger does not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner.
After use, carefully clean the blades. After cleaning, apply a film of light machine oil to prevent the blades from rusting.

Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:

Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 5 A.

Protecting the environment

**** Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to
local provisions. Further information is available at www.2helpU.com

Technical data

| | BEHT201 Type 1| BEHT251 Type 1
---|---|---|---
Voltage| VΑϲ| 230| 230
Power input| W| 420| 450
Blade strokes

(no load)

| min-1| 1960| 1815
Blade length| cm| 45| 50
Blade gap| mm| 16| 18
Blade brake time| s| < 1| <1
Weight| kg| 1.91| 2.16
Level of sound pressure according to EN 60745:

Sound pressure level at the operator position (LpA) 85 dB(A), uncertainty (K) 3 dB(A)
Sound power level (LWA) 97 dB(A), uncertainty (K) 2.5 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah, D) 2.5 m/s², uncertainty (K) 1.5 m/s²

EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE

BEHT201, BEHT251– Hedge Trimmer
Black & Decker declares that these products described under
“technical data” are in compliance with:
EN60745-1:2009+A11:2010,
EN60745-2-15:2009+A1:2010
2000/14/EC, Hedge trimmer, Annex V
Measured sound power level (LwA) 97 dB(A)
Uncertainty (K) 2.5 dB(A)
Guaranteed sound power (L) 100 dB(A)
These products also comply with Directive
2006/42/EC, 2014/30/EU, and 2011/65/EU.
For more information, please contact Black & Decker at the following address or refer to the back of the manual.
The undersigned is responsible for the compilation of the technical file and makes this declaration on behalf of Black & Decker.

R. Laverick
Engineering Director
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
31/01/2018

Guarantee

Black & Decker is confident in the quality of its products and offers consumers a 24-month guarantee from the date of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance with Black&Decker Terms and Conditions and you will need to submit proof of purchase to the seller or an authorized repair agent. Terms and conditions of the Black&Decker 2-year guarantee and the location of your nearest authorized repair agent can be obtained on the Internet at www.2helpU.com, or by contacting your local Black & Decker office at the address indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and receive updates on new products and special offers.

United Kingdom & **Republic Of Ireland
www.blackanddecker.co.uk
emeaservice@sbdinc.com| Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD| Tel.
Fax| 01753 511234
01753 512365
---|---|---|---
Middle East & Africa**
www.blackanddecker.ae
service.mea@sbdinc.com| Black & Decker
P.O.Box – 17164
Jebel Ali Free Zone (South), Dubai,
UAE| Tel.
Fax| +971 4 8863030
+971 4 8863333