MagiDeal BLS-B35 BT Digital to Analog Audio Converter Instruction Manual
- June 5, 2024
- MagiDeal
Table of Contents
MagiDeal BLS-B35 BT Digital to Analog Audio Converter
Product picture
Product description
This product is a wireless receiver & digital optical fiber to analog audio converter, U disk player all-in -one device, the product is simple to operate, can freely receive most of the Bluetooth audio, through this product can convert digital audio into analog audio signals. The music in the mobile phone can be wirelessly transmitted to the audio equipment. Suitable for TVs. game consoles, CD players, MP3, etc. It perfectly solves the limitations of audio equipment and expands the functions of various audio equipment.
Product main parameters
- Name: Wireless Receiver & Audio Converter
- Model : BLS-B35
- Frequency response range: 10Hz-20kHz output
- Signal to noise ratio: >110dB
- Distortion + noise: <0.02%
- Version: BT5.1
- Name: BLS-B35
- Interface: stereo analog/AUX/RCA/3.5mm/U disk
- Output impedance: 75 ohms
- Decoding chip: 5.1
- Output: RCA/3.5mm
- Effective distance: 20 meters
- Performance: HiFi level
- Support: A2DPIAVRCP
- U disk support format :WAV.WMA.APE.FLAC.MP3
Operation function
On/off:
- Turn on the knob, and the blue indicator light will be on after turning on, and it will enter the Bluetooth mode.
- The knob turns off, and the blue indicator light goes out after turning off.
- The knob key can adjust the volume, easy to operate.
Key Function:
Short press the left and right buttons to cut the song up and down, the middle button to play/pause, and long press to switch BT/digital-analog conversion.
Digital optical fiber conversion analog audio
- Turn on the device, the Bluetooth light is on, press and hold the middle button to switch to DAC mode, the red light is on
- Insert the optical fiber cable into the interface at the input end, and connect the 3.5mm or RCA cable to the output end to connect with audio, power amplifier and other equipment to realize digital analog conversion audio output.
Bluetooth receiving mode
- Turn on the device, the blue light flashes, and wait for Bluetooth pairing at this time.
- Connect the output end to the AUX/RCA line and connect with audio amplifiers and other equipment.
- Turn on the Bluetooth function on the mobile phone or tablet, search for Bluetooth devices, select “BLS-B35 in the Bluetooth list and click to connect to the device.
- After the connection is successful, the blue indicator light is always on.
U Disk Play Mode
- U diskis inserted into the USB interface of the device to automatically recognize and read the music playback in the U disk. (Support MP3, WAV, WMA, APE, FLAC playback format)
- Connect the output end to the AUX/RCA line and connect with audio amplifiers and other equipment.
Note: The default power-on mode of this product is the Bluetooth receiving mode; the U disk is not connected to the device and cannot be switched to the U disk playback mode.
Packing list
- Host 1
- Product manual”1
- Charging cable”1
- Fiber optic cable 1
- 3.5mm audio cable”1
- RCA audio cable1
Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>