Drone-Clone Xperts QuadAir GPS 4K Foldable Drone Instruction Manual

QuadAir GPS 4K Drone Upgrade
FOLDABLE DRONE
MANUAL

www.DroneCloneXperts.com

IMPORTANT STATEMENTS AND SAFETY GUIDELINES

Thank you for choosing this product, in order to make it easier for you to use this drone, please read this manual carefully before operating it, and please save this manual for adjustment and repair the drone in the future.

Important Statement

• This product is not a toy, it integrates expertise in mechanics, electronics, aerodynamics, high-frequency launching, etc. This drone integrates precise equipment, which requires proper assembly and commissioning to avoid accidents. The drone holder must operate the drone in a safe way; improper handling will cause serious personal injury or property damage.
• This product is suitable for people who have experience in operating drones and are older than 14 years old.
• In case of a problem with use, operation, maintenance, etc., please contact your local dealer or the relevant staff of the company. Factory and the seller is not responsible for any injury or damage caused by improper use or operation.
• The product contains tiny parts, so keep them out of the reach of children to avoid eating or suffocating.

Safety Precautions

The RC drone is a dangerous commodity, please stay away from the crowd while flying. Improper assembly or damage to the drone, poor control, and unfamiliar operation cause unpredictable accidents such as drone damage or personal injury. Pilots should pay attention to flight safety, and understand the responsibility for the accident caused by negligence.

• Stay away from obstacles and people The flying drone has an uncertain flight speed and state, there is a potential danger. Flying away from crowds, high-rise buildings, high-voltage power lines, etc., while avoiding flying in windy, rainy, and lightning. Commissioning and installing the drone must be strictly in accordance with the instruction, be careful the distance between the drone with the people should maintain in 1-2 meters. Avoid the drone from hitting the head, face, and body in flying and landing.

• Keep away from the humid environment. The interior of the drone is composed of many sophisticated electronic components and mechanical parts. Therefore, it is necessary to prevent the drone from getting wet or moisture, so as to avoid accidents caused by mechanical and electronic component failure. Use a clean rag to clean the surface stains during the maintenance.

• Guided by the experienced pilot The control skills have certain difficulties in the early stage of learning. Try to avoid flying alone, and you need to be guided by an experienced pilot.

• Use this product correctly Please repair the drone with original parts to ensure the safety of the flight. Please operate the product within the scope permitted by the product features and can be used for illegal purposes.

• Safe operation
  1. Please operate the drone only if you are in good shape and have flying skills. Fatigue, trance, or improper operation will increase unexpected risks.
  2.Don’t use it near your ears! Misuse can cause hearing damage.

• Keep away from high-speed rotating parts When the motors of the drone are rotating at high speed, please keep the pilot, the surrounding crowd, and objects away from the motors to avoid injury and damage.

• Keep away from heat The drone is made of metal, fiber, plastic, electronic components, and other materials, so you should keep it away from heat sources and avoid the sun and high temperatures, so as to avoid causing the deformation of the drone.

• Environmental requirements Discarding this product at will may pollute the environment. Please dispose of it properly according to the local laws and regulations.
  Product Description

PRODUCT CONFIGURATION

Packing list
Aircraft”‘ Blades ser2 Guards4
Screwdriver1 USB charging cable1 Remote control1 Battery*1
Basic parameters
Wheelbase:300mm Height:75mm Total weight:248g Battery:7.4V 1200mah 25C Charging time:about 3 hours Flight time:about 13-15minutes

Product Assembly

Blades(with blades clip clamp)installation/demolition
Blades installation:
Install the blades with A on the fixed position of the arm A, install the blades with B onto the fixed position of the arm B, use a screwdriver to unscrew the middle screw and remove the entire blade clamp with two blades, then replace a new one(included in the package), then presses it down, locks the screw and locks it in place.
Tip:
You don’t need to replace single blades, just replace the whole blades clip clamp with two blades (included in the package). If you replace single blades, remove the screw on the blade by turning the screw counterclockwise. Be careful don’t lose the screws.
Tips: Please fold the drone in the order shown in the figure below. Please install the blades as referred in the picture shown, The blades are divided into A and B parts, be careful of the direction of rotation.

• Make sure that type A and B blades are installed in the correct ‘ \ position. If install the blades improperly, they can’t take off.
• Since the blades are thin, be careful to prevent accidental scratches when installing.
• Please use the original blades provided by our factory.
• The blades are the consumable item. If necessary, please purchase it separately.

Guards installation
Insert the 2 guards on the cage into the 2 holes on the bottom of the fuselage and press them into place. ![Drone Clone Xperts QuadAir GPS 4K Foldable Drone

• Fig2](https://manuals.plus/wp-content/uploads/2022/05/Drone-Clone-Xperts- QuadAir-GPS-4K-Foldable-Drone-Fig2-550x197.png)

Charge the battery of the drone
Pressing and pulling the battery out of the main body of the drone, inserting the USB into the adapter (Not included), the USB indicator lights up red, inserting the battery into the USB output, and the USB indicator flashes green, and charging begins. When the charging is completed, the red and green lights are on, and the charging time is about 180 minutes.

Tips:

• Do not charge the battery on the carpet to avoid fire. We will not take any responsibility for injury and damage, caused by the improper charging.
• Insert the plugin the correct way. Do not reverse insert.
• lt is recommended to use the 5V 1-2A adapter for charging.
• lt is not encouraged to use the computer USB port for charging.

Install Battery of Drone
Push the battery into the battery slot of the drone, and the battery is fully clamped in the drone. Check to make sure the battery is in place.

****Reminder: If the battery is not installed properly, It is very likely that the drone sower off aerial and causes the falling object.

• **** When charging the rechargeable battery, keep away from children and must be under adult supervision. Keep away from flammable materials. Charging the battery under the surveillance area. When there is no one in the room, do not charge it.
• Please prevent a short circuit or squeeze the battery.
• The battery connector should not be removed from the drone and avoid short circuits. Avoid short circuit and decompose of battery, or put it into the fire; Do not put the battery near the heat resource (such as in a fire or near the electric heat device).
• The battery can only charge by the recommended charger, and the battery and charger can’t get wet, The drone can be wiped with a clean rag, pulling out the battery and disconnecting from the charger before cleaning. Periodically check the chargers wires, plugs, fuselage, and other, If it is found to be damaged, stop using it until it is repaired.
• The charger is not a toy; the charger can only be used indoors.
• The battery after the flight needs to be recharged before being stored. If you don’t use the battery in a long term, it is recommended to charge the battery once at least every 3 months to prevent the battery from being over-discharged and permanently damaging.

Drone Part Name

Remote Control Part Name

Install the remote control battery

Remove the remote control battery cover, follow the anode and cathode polarity indicated by the remote control, correctly insert the 4 AAA batteries, and then re-install the battery cover.
Remote control battery installation:

• ****The remote control uses 4 “AAA” non-rechargeable batteries or “AAA” rechargeable batteries. (Not included)
• Pay attention to the polarity of the battery when installing or replacing the battery.
• Do not mix different conditions or types of batteries.
• The used battery should be taken out in time, and the discarded battery should be thrown properly.
• If you do not use it for a long time, please remove the battery to avoid damage to the product caused by battery leakage.

Synchronize the drone with the remote control.

1. Insert the battery into the battery compartment of the drone. Put the drone on the horizontal plane. Press the power button of the drone for two seconds to turn it on. The indicator light of the drone flashes quickly and then flashes slowly.
2. Turn on the remote control power switch. The synchronization is completed, the indicator light of the remote control turns on solid, and the front indicator light of the drone is bright.

• ****Without any drone synchronizing with other remote controllers, your remote control and your drone don’t need to synchronize again, as long as the syn is successful.
• When the remote control is synchronizing with the drone, please make sure that there does not have other remote control and the drone is powered on at the same time. Otherwise, it can be failed or wrong.

Drone Initialization Detection

After the synchronizing procedure is finished, keep the drone on the horizontal plane, it will automatically begin the initialization detection. The drone needs about 8 seconds to complete the initialization detection on the stationary plane. Next step, the drone needs to begin the gyro calibration procedure.

Gyro Calibration

After synchronization and initialization are successful, the drone on the horizontal plane pushes the left and right joysticks to the lower right at 45° at the same time as the figure below. Then the front and rear indicators light of the drone flash rapidly, the gyroscope is calibrated, and finally, the indicator light changes from flashing to steady light, and the gyroscope calibration is completed.

• When performing the procedure, be sure to put the drone on a horizontal plane, otherwise, the drone can’t fly in balance.
• The gyroscope is calibrated at the factory, and the user is not required to calibrate it. This operation is only performed when the initialization can’t be exited.

Compass Calibration

1. After the drone synchronizes with the remote control successfully, completed the initialization test and gyro calibration, then perform the compass calibration.
2. Every time the drone takes off, it must be performed compass calibration, otherwise, the drone will not be able to fly normally.
   Compass calibration is divided into two steps:
   Firstly press the compass calibration button as figure below.

Step 1: Horizontal calibration of the compass(Figure 1) Then use your hand- spin the drone as shown below and rotates it counterclockwise horizontally for about 3 times until the indicator light is on, The horizontal calibration is completed.
Step 2: Vertical calibration(Figure 2) Erect the drone and rotate the drone with your hand, as the figure 2 below, rotate the fuselage clockwise about 3 times until the indicator light on the front of the aircraft is always on. The compass calibration is complete.

• Note: The best distance between the ground and the drone should be more than 1 meter during calibration.
• Do not calibrate the drone in strong magnetic fields, such as magnetite mines, parking lots, and foundation building of steel and concrete.
• When performing the calibration, do not carry ferromagnetic substances such as keys, mobile phones, etc.
• Do not perform the calibration near large pieces of metal.

Search satellite signals

After the compass calibration procedure is completed, put the drone on the horizontal plane, the drone will automatically search for the satellite signal, the indicator light of the drone will change from slow flashing to steady light, and the remote control emits a beep, then the procedure of search satellite signal is completed. Unlock the drone by pushing the left joystick to the left at 45° and the right joystick to the right at 45°at the same time(as in the picture shown), the motors will spin, then push the throttle stick, and the drone will take off.

Tips: Please make sure that the drone flies in wide-open space and the satellite signal is more than 7 stars shown in the app before take-off.

FPV real-time transmission application download and Connection

https://itunes.apple.com/app/id1453621522
https://play.google.com/store/apps/details?id=com.klh.lwfpv
Andrew system is required to open the APP and update the map of your location before connecting drone wifi

Click the START button to enter the control interface

Ps: when you use the joystick of the remote control, you need to close the virtual joystick of the app, they can’t work at the same time.

1. Make sure the phone’s GPS function works.
2. Press Self-stabilizing mode to exit the follow-me mode

In follow me mode, the mobile phone continuously sends the location to the drone, and the drone will follow your phone.
When the virtual joystick and the actual joystick activates simultaneously, the actual joystick would take primary control for the direction of orbit mode.

Press the orbit mode icon that the drone will fly surround the mobile device, at the same time push the direction (right) joystick up or down to control the radius decrease or Increase, push the direction joystick to the left or right, that will control the surround direction turning clockwise or counterclockwise. Pushing the throttle (left) joystick to control the drone’s ascend or descend.

Flight

Basic Flight

Step

1. Synchronize the remote control and the drone, then the drone will automatically finish the initialization.
2. Perform the synchronized gyro calibration procedure.
3. Download the APP and the drone with the mobile phone with Wifi.
4. Performing the Compass Calibration procedure. Wait for the drone automatically search satellite signals, usually 60-80 seconds (signals should be more than 7 stars ), until the rear light of the drone is steady on, signals receiving finish.
5. Unlock the drone, then push the throttle stick up, and the drone takes off.

Pre-Flight Inspection

1. Ensure the battery of the remote control and drone is fully charged.
2. Ensure the blades are installed correctly.
3. Ensure the compass calibration is successful.
4. Ensure the drone received a satellite signal of more than 7 stars.
5. Check the motors work fine after unlocking the drone.

Flight Control

Function

One-Key Take off / Landing

• Unlocked the drone, press the button, and the drone will automatically take off and rise about 1.5 meters to hover.
• When the drone is flying, press the button and the drone will automatically land.

Orbit Mode

Ascending the drone 20 meters or higher from the ground. Press the orbit button and the head of the drone turns back to the previous direction and hovers, push the remote control direction (right) joystick to the left or right, the drone will fly Clockwise or Counterclockwise, In the orbit mode, press and hold the direction (right) joystick, the drone accelerates to 2.5M/S. Pull down the direction (right) joystick to expand the radius. The maximum radius is approximately 20 meters. Pushing up direction (right) joystick to reduce the surrounding radius, the minimum is about 5 meters. Press the orbit mode button again to exit the orbit mode.

Headless Mode

Press the headless mode button to enter the headless mode, the taillight of the aircraft indicator flashes quickly, the remote control emits a beep, and press again to exit the mode.

Note: The headless direction is the head of the aircraft before taking off.

Return

The aircraft has a return function. If the return point is successfully recorded before take-off, if the communication signal is lost between the remote control and the aircraft or the return button is pressed, the aircraft will automatically return to the return point and land to prevent accidents. The aircraft has three different return modes:

1. One-key return
2. Out of control return
3. Low battery return
   Return point : During the takeoff or flight, when the GPS signal receives more than 7 stars for the first time, it will be recorded as the current position of the aircraft as the return point.

ONE-KEY RETURN

When the GPS signal is good (the number of satellites is greater than 7), the return can be started by the remote control button. The return flight process is consistent with the uncontrolled return flight. The difference is that when the aircraft returns to land, the user can control the aircraft through the joystick to avoid obstacles. Press the button to exit the return and the user can regain control.

Out Of Control Return

If the GPS signal strength is more than 7 stars, the compass works fine, the drone successfully records the starting point and the remote control signal is lost for more than 6 seconds, the flight control system will take over control of the drone and control the drone fly back to the starting point. Even if the signal of the remote control is restored during the flight, the drone will continue to return, but the user can exit the flight control system and regain control of the drone by pressing the direction joystick of the remote control.
Notice:

• The drone can’t dodge obstacles during the automatic return flight.
• When the GPS signal is not good or the GPS function is not working, it can’ return.
• If the drone did not receive the satellite signal and the remote control signal is lost for more than 6 seconds, the drone unable to return to the starting point, and it will slowly descend, landing and lock.

Low Power Return

• The rear indicator light of the drone flashes slowly. At this time, the remote control continuously emits “beep beep beep…, beep beep beep…”. As long as the drone flies higher than 20 meters or the distance between the drone and the remote control is farther than 20 meters, the drone will automatically carry out the return function. Fling back to the starting point.
• The voltage of the drone is below the safe value, the drone will automatically land to the starting point
  Tips: When the drone is in a low-power state and returning starting point, the remote control can’t cancel the return.

Take a Photo / Recording Video

During the flight, the camera can adjust the angle up or down, press the camera up button of the remote control each time, and the camera lens ascends about 10 degrees. When the camera is at the maximum angle and the remote control emits, how many times you press it, the camera can’t ascend, the camera down button is the same.
During the flight, you can use the camera/video button of the remote control to capture the aerial image. Pressing the camera button, the camera will take a photo, at the same time the remote control em is “beep”, holding the video button, and the camera will start recording video, at the same time the remote control emits “beep” twice, holding this button again to finish.

Common troubleshooting

The drone is in the gyroscope detection state, please put the drone on a stationary surface or on the ground.
2| After the drone takes off, it can’t hover and tilt to one side.| Put the drone on a flat or level surface and calibrate the gyroscope.
3| The drone is shaking very badly| Blades deformation, it needs to replace the blades.
4| The drone can’t be unlocked, the taillights flash quickly| The battery voltage of the drone is too low, please fully charge the battery

BRAND: EACHINE
ITEM NAME: 520S
Manufacturer: Shenzhen Feijiada Technology Co., Ltd.
Address: Room 428, No.2 Jinfanghua E-commerce Indu
stria! Park, No.450 Bulong road,Longgang d is
strict, Shenzhen City, Guangdong, China
Importer: Lotus NL B.V.
Address: Koningin Julianaplein10,
le Verd, 2595AA. The Hague.The Netherlands. E-mail: peterfglotusnl.com
Tel:+31645171879(English).+31626669008(Dutch)
♦ [email protected] https://www.eachine.com/

References

• Drone-Clone Xperts

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>