SPEX LIGHTING SLWZ-SNC-01 Smart Room Controller User Manual
- June 5, 2024
- SPEX LIGHTING
Table of Contents
LIGHTING SLWZ-SNC-01 Smart Room Controller
User Manual
Limited 3-Year Warranty
For complete warranty information, including details on consumer legal rights
as well as warranty exclusions, visit www.liteline.com/warranty.
Before you start
IMPORTANT: Review this installation guide in its entirety before starting
the installation of your Room Controller or removal of your old switches.
Installation and maintenance involving electrical wiring must be done by a
qualified person(s). Risk of Electric Shock: Electricity can cause personal
injury and property damage if handled improperly. The metal heatsink plate is
not grounding, which might become live.
NOTE: INSTALLATION OF THIS PRODUCT REQUIRES A NEUTRAL WIRE. IF THE
NEUTRAL WIRE IS NOT CONNECTED, THIS SWITCH WILL NOT WORK. CONSULT A QUALIFIED
ELECTRICIAN. THE ROOM CONTROLLER IS ONLY COMPATIBLE WITH ON CLOUD OR WIZ
CONNECTED LIGHTS.
CAUTION: To reduce the risk of injury and/or overheating and damage to
other equipment:
- Make sure that the power at the circuit breaker is turned OFF before starting.
- A neutral (typically white) wire is required.
- The wire colors indicated in this manual are typically found and may differ in some constructions/regions.
- Ensure the wire conductors are securely fastened to each wire.
- It is recommended that a certified electrician completes all high voltage electrical installations.
- Must follow all building and electrical codes in the region when installing.
- Ensure the Wi-Fi router’s 2.4GHz signal is strong at the switch/luminaire location (-80dB min).
- Do not install to control an appliance, motor, receptacle or traditional bulb/fixture.
- Recommended to be installed in a minimum 2.5″ depth device box.
- Intended for installation in an in-wall electrical box.
Product overview
Specifications
Wireless Frequency:……………2.4GHz
Wireless Security:……………..Counter with CBC-MAC (CCM)
Input:……………….120VAC, 60Hz
Output:………………………………. 5A, 600W max
Compatible Load(s):……………….. OnCloud or WiZ Connected products only
What you need
Switch Functions
BUTTON | LED COLOR | ACTION |
---|---|---|
Short press ON switch | GREEN | Lights turn ON |
Short press OFF switch | GREEN | Lights turn OFF |
ON Long press (7-10 seconds) | GREEN | Line voltage relay ON, lights turn ON |
OFF Long press (7-10 seconds) | RED | Line voltage relay OFF, lights turn OFF |
ON and OFF long press (5 seconds) Note: For first time pairing, follow with a
short press ON For previously paired, follow with a long press ON (3 seconds)|
FLASHING RED FLASHING RED/ GREEN| Enter 2.4GHz wireless pairing
ON 5 rapid clicks (within 3 seconds)| OFF| Disable/Enable the LED indicator
light
Color Temperature Rocker| GREEN| Color temperature becomes cooler in 10%
increments
Color Temperature Rocker| GREEN| Color temperature becomes warmer in 10%
increments
Brightness Rocker| GREEN| Brightness increases in 10% increments
Brightness Rocker| GREEN| Brightness decreases in 10% increments
Previous Scene| GREEN| Cycle to the previous scene (see WiZ app)
Next Scene| GREEN| Cycle to the next scene (see WiZ app)
PAIRING: The Room Controller initiates wireless pairing for all OnCloud / WiZ Connected light fixtures that are hardwired to the Room Controller circuit.
Installation
-
Turn OFF the power at the circuit breaker and confirm with the voltage tester at the switch before proceeding. Place voltage tester against the existing switch checking the wall plate, screws and switch at various points to determine that there is no power present.
-
Remove the wall plate and pull out the existing light switch so that all wires are exposed outside of the gang box (do not disconnect wires).
-
Label the live wire with a piece of electrical tape.
-
Disconnect and remove the Single-Pole Wiring existing switch.
-
Connect the Room Controller
Single-Pole Wiring 3-Way Wiring Diagram 1 3-Way Wiring Diagram 2
NOTE: Only the above 3-way wiring configurations are supported. Excluded wiring configurations include power going straight to the load, and no neutral wire going to devise boxes. -
Mount the Room Controller in the existing gang box with the provided screws and attach the wall plate (press fit).
-
Turn on the power at the circuit breaker.
-
Test to see that the Room Controller is functioning by pressing and holding the ON switch for 7-10 seconds. Your load (lights) should turn ON.
NOTE: If your lights do not turn on, check that the live/load wires are all connected according to the old switch. Turn off power at the circuit breaker and check the wiring. -
Place the OnCloud / WiZ Connected light fixtures that are hardwired to the Room Controller circuit in pairing mode
NOTE: If the OnCloud / WiZ Connected light fixtures are already installed and paired in the WiZ app, skip to #10.
a. Press and hold the ON and OFF buttons simultaneously for 5 seconds. The LED indicator will flash RED.
i. For first time pairing, follow with a short press of the ON button.
ii. For previously paired, follow with a long press (3 seconds) of the ON button.
b. The LED indicator will flash RED/GREEN.
c. The fixtures are now in pairing mode and you can proceed to WiZ App Setup. NOTE: In the WiZ App, any OnCloud / WiZ Connected fixture(s) must be added to a room prior to adding the Room Controller that will control them. -
WiZ APP SETUP Refer to “WiZ Quick Setup Guide”
Troubleshooting
PROBLEM | CAUSE | SOLUTION |
---|
Unable to find the OnCloud / WiZ Connected light fixtures that are hardwired to the Room Controller circuit on the network|
Room Controller may not have initiated Connectivity Mode
| Long Press the ON and OFF switch simultaneously for 5 seconds to enter into Connectivity Mode: Searching for Wi-Fi Network.
Unable to operate the load (light) with the ON/ OFF switch
| Wiring issue| Review and confirm the
INSTALLATION section in this manual.
No electricity| Check that the power is ON at the circuit breaker.
Load does not function or is incompatible| • Replace the load.
• Check the SPECIFICATION section for compatible loads and limitations.
OnCloud / WiZ Connected light fixtures that are hardwired to the Room Controller circuit not responding to WiZ APP control
| The network is not connected| Check wireless network connectivity.
Permissions are not granted on a mobile device| Check to see that permissions
are granted for the WiZ APP.
The room Controller is not functioning correctly| Manually press and hold the
ON switch for 7-10 seconds to ensure electrical functionality is working.
Load (light) not functioning properly| Load (light) may not be compatible or
exceeding limits| • Check the SPECIFICATION section to ensure load (light) is
within limits.
• Replace the load (light).
OnCloud / WiZ Connected light fixtures that are hardwired to the Room
Controller circuit not connecting to the WiZ APP| The Wi-Fi password is
incorrect| Re-enter the Wi-Fi password.
Weak/low Wi-Fi signal| Check Wi-Fi signal to ensure within range of router
(-80dB min).
Wi-Fi not connected| Confirm the Wi-Fi router is broadcasting a 2.4GHz signal.
Re-connect.
WiZ Quick Setup Guide
Downloading the WiZ App
Before you start, make sure you install the WiZ App from either Google Play or
the Apple
App Store (both offer the same set of features). The app can also scale
to fit tablets as needed.
Installing and pairing with the room controller
The OnCloud / WiZ Connected light fixtures are connected through the app and
will only operate on your home’s 2.4GHz Wi-Fi network. Most new routers are
dual bandwidth (both 2.4GHz and 5GHz), ensure you select the 2.4GHz network
which covers a wider range than the 5GHz. To make sure your phone is on the
2.4GHz network, either select it in the list of available networks on your
phone or go into the router settings and temporarily de-activate the 5GHz
network (you can activate it again after pairing is done).
If this is not possible and the OnCloud / WiZ Connected light fixtures are not
found, try initiating pairing mode from the room controller by holding the ON
and OFF button for 5 seconds (or until the indicator lights flash red)
followed by a short press of the ON button (LED indicator will flash
RED/GREEN), then walking a short distance away from the router. Due to the
short range of 5GHz networks, your phone should auto-connect to the 2.4GHz at
this point. Once connected, you can start pairing in the app. You can pair as
many devices as you want at the same time.
NOTE: Upon first boot-up, the firmware may need to be updated. Please
allow up to 1 minute for the OnCloud / WiZ Connected light fixtures to update
after completing WiZ app setup. For additional support, visit
www.liteline.com/WiZsupport
NOTE: In the WiZ App, any OnCloud / WiZ Connected fixture(s) must be
added to a room prior to adding the Room Controller that will control them.
Please refer to the Installation manual included with the OnCloud / WiZ
Connected light fixtures for setup.
The following importer is the responsible party:
LLC Sales, Inc. DBA Liteline USA
1209 Orange Street, Wilmington, DE, 19801 liteline.com/contact-
us
Changes or modifications not expressly approved by the responsible party could
void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) reorient or
relocate the receiving antenna; (2) increase the separation between the
equipment and receiver; (3) connect the equipment into an outlet on a circuit
different from that to which the receiver is connected; (4) consult the dealer
or an experienced radio/TV technician for help.
RF Exposure Requirements:
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter
and must be installed to provide a separation distance of at least 20cm from
all persons.
ISED Canada Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) this device
may not cause interference; and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This product must be installed in accordance with the applicable installation
code by a person familiar with the construction of the product and the hazards
involved.
LITELINE CORPORATION
Telephone 1.866.730.7704
Fax 1.888.738.9736 liteline.com
UM_SLWZ-SNC-01_3.26.21
Copyright © 2021, Liteline Corporation.
All rights reserved.
References
- Liteline - Home - Canada’s leading lighting manufacturer
- Liteline - Contact Us for help with your lighting needs.
- Liteline - Description of our product Warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>