Markbass Nano Mark II Head Owner’s Manual
- June 5, 2024
- Markbass
Table of Contents
Markbass Nano Mark II Head
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions;
- Keep these instructions;
- Heed all warnings;
- Follow all instructions;
- Do not use this apparatus near water;
- Clean only with dry cloth;
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions;
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat;
- Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet;
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus;
- Only use attachments/accessories specied by the manufacturer;
- Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from the tip-over (and Fig 21 DU Tipping Cart Symbol).
- Unplug this apparatus during lightning storms or when unused for long periods of time;
- Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped;
- “Warning: to reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture; and objects lled with liquids, such as vases, should not be placed on this apparatus”;
- To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug fron the AC receptacle;
- The mains plug of the power supply cord shall reamin readily accessible.
- In case of voltage selector make sure the switch on the rear panel is on the correct voltage before connecting it to the AC power, and the fuse is the right value for that voltage (This selector is not available on the 100V version). Please change the voltage/fuse values label located near the voltage selector matching the voltage/fuse values when you need to change the voltage of the apparatus.
- “WARNING: this apparatus must be securely attached to the oor or wall in accordance with installation istruction. Tipping, shaking, or rocking the machine may cause injury or death.”
FRONT PANEL
- UNBALANCED ¼” INPUT JACK
- SOLID STATE GAIN
- CLIP LED
- LOW EQUALIZATION CONTROL KNOB
- MID LOW EQUALIZATION CONTROL KNOB
- MID HIGH EQUALIZATION CONTROL KNOB
- HIGH EQUALIZATION CONTROL KNOB
- MASTER VOLUME LEVEL KNOB
- SCOOPED-MID EQ LED
- MAIN ON/OFF SWITCH
REAR PANEL
- AC POWER SOCKET
- FOOTSWITCH INPUT
- RETURN EFFECT ¼” JACK
- SEND EFFECT ¼” JACK
- PRE/POST EQUALIZATION CONTROL SWITCH
- GROUND LIFT CONTROL SWITCH
- LINE OUT XLR
- SPEAKER OUT SPEAKON / ¼” COMBO JACK
TECHNICAL SPECS
- INPUTS
- INPUT : impedance 1 Mohm, max. voltage 15 Vpp
- EFFECT RETURN : impedance 33 Kohm, max. voltage 10 Vpp
- CONTROLS
- GAIN: –60x dB to +23 dB range
- PRE/POST EQ (for line out): switch on rear panel
- GROUND LIFT : switch on rear panel
- MASTER VOLUME
- EQUALIZATION
- LOW: center frequency: 60 Hz; level: ±16 dB
- LOW MID: center frequency: 360 Hz, level: ±16 dB
- HIGH MID: center frequency: 800 Hz, level: ±16 dB
- HIGH: center frequency: 5 kHz, level: ±16 dB
- OUTPUTS
- LINE OUT : balanced XLR, max. voltage 10 Vpp
- EFFECT SEND: unbalanced, max. voltage 20 Vpp (pre-EQ)
- TUNER OUT : unbalanced, max. voltage 2 Vpp
- SPEAKER OUT: speakon/1/4” combo
- OTHERS
- WEIGHT : 3.20 lbs / 1.45 kg
- DEPTH : 8.27 in. / 21 cm
- WIDTH: 7.87 in. / 20 cm
- HEIGHT: 2.09 in. / 5.3 cm
- OUTPUT POWER: 300W RMS @ 4 ohms,
- 150W RMS @ 8 ohms
- BI-BAND LIMITER
- OPTIONAL FOOTSWITCH: flat/scooped MID/FSW EQ
BLOCK DIAGRAM
WARRANTY
Markbass offers an international limited warranty on Markbass products purchased from any authorized Markbass dealer, effective from the day of purchase. The terms of this warranty vary from country to country; please contact the Markbass distributor in your country for details. Please register this product online at www. mark bass.it to establish the date of purchase. However, please note that you are required to retain a copy of your receipt as proof of purchase in order to receive warranty service. This warranty does not apply to any damage to the product caused by misuse, mishandling, accident, abuse, alteration, modification or unauthorized repairs. Product appearance and normal wear and tear (worn paint, scratches, etc.) are not covered by this warranty. Markbass reserves the right to be the sole arbiter regarding the misuse or abuse of this product. Markbass assumes no liability for any incidental or consequential damages, which may result from the failure of this product. Any warranties implied in fact or by law are limited to the duration of this express limited warranty. Your legal rights related to the warranty will vary depending on the country of purchase.
WARRANTY CARD
This product is guaranteed by the warranty provided in the country of
purchase, under the following conditions: A – The Markbass warranty is only
applicable if this document been properly completed (here or online) and if
the original invoice/bill of sale, mentioning model, serial number and
purchase date, is presented together with this document. B – The obligations
of Markbass are limited to the repair of defects. Warranty repair eligibility
will be decided at the sole discretion of Markbass or its representatives.
Freight, freight insurance costs, and any other costs related to the repair of
this product are not covered by this warranty. If any problem occurs, please
don’t hesitate to contact our support team at service@markbass.it.You can fill
out this form and send a copy to Markbass (Parsek srl, Via Po 52, 66020 San
Giovanni Teatino, CHIETI ITALY) or, even better, you can now register your
warranty online in a matter of minutes, using our online registration form at
www.markbass.it. Simply point, click and type in your information…and you’re
done! Registering your warranty identifies you and your product, in case you
are ever in need of warranty service. Please note that in order to qualify for
warranty service, you must retain a copy of the sales receipt or bill of
delivery as proof of purchase.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>