BRASQ PS300 Paper Shredder Chips Instruction Manual

BRASQ PS300 Paper Shredder Chips

Setup

1. Place the CD/DVD & Credit card shredding plastic bin provided with your shredder, inside the appropriate rib position attached to the inside of waste bin.
2. Place the shredder securely on top of the waste basket. Be sure not to allow your fingers to get between the basket and the shredder as you are placing the shredder in place.
3. Plug the power cord into any standard 230-240 volt AC out let.

Operating the shredder

The Main Switch is located on the top of the shredder. The Main Switch has three (3) settings.

1. When AUTO is selected, the shredding process is started automatically by inserting the paper, a disk or a credit card into the feed opening. When inserting papers, please do not shred CD/DVD and credit card at the same time. When inserting CD/DVD and credit card, also please do not shred paper at that time. The shredder will stop automatically when the paper, a disk or a credit card has completed its travel through the feed opening.
2. REV is used to assist in the removal of a paper jam, which reverses the shredder process prior to a completed cycle, thus clearing the cutters.
3. OFF is used to terminate the AC power to the shredder. The mode is recommended when emptying the wastebasket or when the shredder is not in use for a prolonged period of time.

Shredder capacity

• PS300 will shred 10 sheets of A4 size 80g/gsm paper, a CD/DVD disk or credit card at once and will accept paper widths up to 220mm. When shredding small material like envelopes or receipts, insert them through the middle of the feed opening.

Cautions

1. Keep all loose articles of clothing, ties, jewelry, hair, or other small items away from the feed opening to prevent injury.
2. Keep in the OFF position when the shredder is not in use for prolonged periods of time.
3. Remove all paper clips and staples from paper before shredding.
4. Do not place hands or fingers into the shredder throat as it can result in serious injury.
5. Always turn off or unplug the shredder prior to moving, cleaning or emptying the wastebasket.
6. Empty wastebasket frequently.
7. The document shredder must always be deactivated and disconnected from the electrical line prior to moving, transporting and cleaning the device and prior to emptying the waste basket.
8. Please do not leave the document shredder unattended e.g. in the event children’s pets are nearby.
9. Please do not shred credit cards, CDs/DVDs, and paper at the same time.
10. The device may not be operated with a damaged power cord.
11. For indoor use only.
12. To protect the machine well, we suggest the user to operate it in this way: work 3 minutes then rest one hour.
13. Please do not spray any flammable gas or oil onto this shredder, it may cause fire.
14. Please read the manual before operating the machine
15. Sharp edges, do not touch once you take out the waste bin
16. This equipment is not intended for use by children, avoid touching the media feed opening with the hands, clothing or hair, unplug this equipment when not in use for an extended period of time, hazardous moving part is in this equipment, keep body parts away from moving parts

Paper Jams and overload protection
PS300 is equipped with a motor overload protection device. The normal short duty cycle for continuous shredding at maximum capacity is 3 minutes. The power may terminate automatically in case of the following abnormal situations:

1. Operating the shredder at the maximum capacity continuously for a prolonged period of time, e.g. more than 3 minutes for computer paper and CD/DVD or credit card without stopping.
2. Exceeding the shredding capacity e.g. inserting more than 10 sheets at one pass, or if the paper is not fed squarely into the feed opening.

Both abnormal operations may result in the activation of the automatic motor overload protection, which terminates the power to the unit. If this occurs, you should:

1. Unplug the power cord from the AC outlet to allow shredder to cool down. Tear or cut off any excess paper from the top of the shredder.
2. Plug the power cord back into the AC outlet and place the Switch in REV. Pull the remaining paper out of the cutters. Place the Switch back to the Auto position if necessary clear the feed opening of any remaining shredded pieces of paper, Keep fingers away from feed opening to avoid harm.
3. With the Main Switch in the AUTO position and the feed opening clear, you are now ready to resume normal shredding.

Specifications

• Shred type
• Shred Size
• Shredding Capacity
• Feed Opening
• Feed Opening for CD/DVDs
• 120mm
• Input
• Shredding Capacity
• Shredding speed
• Basket capacity
• Dimensions
• Security level (DIN 66399-2)
• P-4
• 240 VAC, 50Hz, 1.2A
• 10 Sheets
• 1,6m/min
• 21 L
• 351 x 220 x 443mm

Guideline 2012/19/EU concerning the handling, collection, recycling and disposal of electrical and electronic equipment and their components (‘waste electrical and electronic equipment’, known as WEEE). The crossed symbol on a rubbish container indicates that the machine or device is not allowed to be disposed of but it must be handed over to a suitably equipped collection center for proper recycling or disposal.

CE

This machine corresponds to the requirements according to EU Guideline
2014/30/EU ’Electro-Magnetic Compatibility’ 2014/35/EU entitled Low-Voltage Guidelines.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>