Rowenta RR7987 X-Plorer Serie 95 Robot Vacuum Cleaner User Guide

User’s guide
X-plorer Serie 95

RR7987 X-Plorer Serie 95 Robot Vacuum Cleaner

Please read carefully the “Safety and use instructions” booklet before first use
For more information

Your robot may encounter some difficulties on carpets: with fringes, too thick, with long piles, or too light (ex: bathroom carpet)

1.

1. Power / Start Pause
2. LDS (Laser Distance Sensor)
3. Recharge / Spot cleaning
4. WIFI indicator LED
5. Reset button
6. Button for taking out dust box and water tank
7. Dust box and water tank
8. Air outlet
9. Collision bumper
10. Follow wall sensor

1. Dust box and water tank
2. Water outlet adapter
3. Filter
4. Dust bin opening button
5. Water inlet
6. Water inlet cap
7. Buckle
8. Dust box and water tank separation button
9. Pleated filter
10. Foam filter
11. Pre-filter

1. Anti-drop sensor
2. Side brush
3. Wheel
4. Water outlet
5. Charging electrode
6. Caster
7. Rolling brush
8. Rolling brush cover

1. Lock
2. Water outlet
3. Removal button
4. Slot
5. Washable mop

Remove the bottom cover and connect the docking station with the adapter, and pay attention to arranging adapter connection wires to avoid being wound during the sweep. Put the bottom cover back.

To place the docking station, make sure there is an empty area of 0.5m on the side and 1.5m in front of the docking station. Do not install the docking station near stairs. The cable must be tight. Always place the docking station on the hard floor. Do not place the docking station on the carpet.

Connect the adapter to a wall socket. The docking station lights when the robot is not plugged in. Remove the protective strip on the bumper to ensure proper operation of the device.

Please fully charge the robot before using it for the first time. To do so, place the robot on the docking station and align it to the charging terminal. When the robot is correctly plugged, the docking station light will switch off. When the white indicators on the robot are normally set on, the robot is fully charged (4-5 hours).

In order to extend the battery lifespan, always keep the robot charging on the docking station while not using it.
When not using the vacuum cleaner for a long time, please fully charge the battery, switch off the robot and store the robot in a cool dry place.

The robot has drop sensors to detect stairs and gaps. The robot will change direction when detecting them. In order to correctly detect the floor level difference, make sure there are no objects (bags, shoes …) on the floor next to gaps, stairs, or on the stairs’ steps. The robot near stairs without objects . The robot near stairs with shoes, bags, or other objects (the robot will not properly detect the stairs and therefore fall).

Press the button during 3 seconds to turn on the power (when the robot is not being charged). The white indicator will be normally set on. Reversely, press the button during 3 seconds to turn off the power.

When the robot is turned on, press the button to start automatic cleaning (or use
X-plorer Series 75/95 app, see section 2).
Press again to suspend cleaning.
Press to stop current cleaning and return to the docking station.
The robot automatically goes back to the docking station under one of the following conditions:

• The robot has completely cleaned
• Battery power is insufficient; once the battery is charged to 80%, the robot will resume completing the remaining cleaning work

Press the button during 3 seconds to start spot cleaning mode. The robot will focus on a 1,5m x 1,5m specific area. After the whole area has been swept, the robot will automatically return to the charging dock.

2.

To fully benefit all the possibilities of your robot, download the free app “Rowenta X-plorer Series 75&95” (you can use the QR code above to find it on AppStore or Google play) on your smartphone. Just follow the instructions in the application to enjoy the robot!

When the white indicator is flashing slowly, the device is waiting for a connection. When the white indicator is flashing rapidly, the device is connecting to WIFI. When the white indicator is normally set on, the device is connected!

3.

4.

Wipe robot sensors with a dry, soft cloth including:

• Wall sensor on the right side of the robot
• Four anti-drop sensors on the bottom of the robot
• Infrared anti-collision sensor in front of the robot on the bumper

Please also wipe charging electrodes and the window of the charging dock regularly

To clean the dust box and water tank, open the robot cover, press the release button and remove the dust box and water tank.
Press the open button of the dust box and empty the dust box. Tap the dust box to knock off excess dirt.
Take out the foam filter and pleated filter. Clean the filters with the cleaning tool.
Users can also wash the filters for deep cleaning.
Press the release button of dust box to separate the dust box from the water tank.

Flush the water tank, dust box, and filter module thoroughly with water.
Let the water tank, dust box, and filter module naturally dry for the next use.
Put the pre-filter, foam filter, and pleated filter back, and put the filter module back into the dust box.
Reinstall the water tank and dust box, and then install the module back on the machine.

To clean the central brush, turn the robot OFF and turn the robot upside-down. Press down the locker to take out the protective cover. And take out the central brush upwards. Clean the central brush with the cleaning tool.

To replace the central brush after having cleaned it, put one end of the central brush into the corresponding hole first. Then press the brush cover and fix it with the locker

To clean the side brush, remove it by unscrewing it and use a cleaning brush to clean the side brush and the entanglements in the slot of the side brush. Clean side brushes once a month.

Replace side brushes every 6 months. Throw away the old brushes and replace them with new ones. Screw the new brushes on the robot.

To clean the wheels, clean the front, left, and right wheels once a month. The wheel shaft may be entangled by the hair, cloth strips, etc. so please clean it in time!

Every 6 months replace the pleated filter and the foam with new ones to maintain optimal performance.

Do not throw the robot in the bin. Always wear gloves and protection. Remove the 5 screws. Remove the bottom cover. Take off the battery. Unplug the battery connector.

supply.
• Make sure the battery is fully charged.

The robot suddenly stops working

| • Check whether the robot is stuck or blocked by obstacles.
• Check whether the battery is too low.
• If the problem persists, please shut it down, wait for 3 seconds, and then restart it.
• The appliance may be overheating :
–  Stop the appliance and leave cool for at least 1 hour.
–  If it overheats on repeated occasions, contact the Approved Services Centre.

Cannot charge the robot

| • Check whether the indicator on the charging dock is on (when the robot is not on the charging dock).
• If not, check that the charger is properly connected or contact an Approved services Centre to change the charger.
• Check whether the indicator on the charging dock is off and the indicator on the robot is flashing during charging.
• Wipe dust off charging electrodes with a dry cloth.
The charger is getting hot| This is perfectly normal. The vacuum cleaner can remain permanently connected to the charger without any risk.

The robot cannot return to the charging dock

| • Clear the charging dock of objects within 0.5m on the left and right sides and within 1.5m ahead.
• Make sure that the robot starts cleaning from the charging dock without abnormal movement.
• When the robot is near the charging dock, it can return faster. But if the charging dock is located far away, the robot will need more time to return. Please wait for its return.
• Clean charging electrodes.

The cleaning schedule is not executed

| • Make sure the robot has been powered on.
• Set the time and schedule the time for automatic cleaning with the app.
• Make sure the appointment time has been set correctly.
• Check whether the battery level is too low to start cleaning.
• The robot will not start any scheduled cleaning when the task is being performed.

Suction whistling

| • Check the suction inlet for any obstruction.
• Empty the dust box.
• Clean filters.
• Check whether filters are wet due to water or other liquids on the floor. Let filters dry naturally thoroughly before use.
• The dust collector is not properly fitted :
–  re-position it correctly.
• The intake head is clogged :
–  remove the power brush and clean it.
The rolling brush does not rotate| • Clean the rolling brush.
• Check whether the rolling brush and the brush cover are installed correctly.
Abnormal action or sweep route of the robot| • Carefully clean the sensor with dry cloth.
• Restart the robot.

No water released during mopping

| • Make sure there is enough water in the water tank.
• Check whether the mop module is installed correctly.
• Check whether the water outlet is blocked.
The robot cannot connect to your Wi-Fi network| Ensure that your Wi-Fi router supports 2.4GHz and 802.11 b/g/n bands as this equipment does not support 5GHz bands.

**According to model: ***
When the robot fails, the red indicator on the robot will blink. Please check on the App the stated error code.

stuck. Please tap repeatedly to remove foreign matters. If there is no foreign matter, please relocate it and then start it.
Error 2: A wheel is stuck. Please check whether any foreign matter is stuck in the wheel, or move it to near its home position to start it.| If any wheel is stuck, please check whether any foreign matter is stuck in the wheel, or move it to near its home position to start it.
Error 3: A side brush is stuck, please check.| The side brush may be entangled with foreign matters. Please clean and restart it.
Error 4: The rolling brush is stuck. Please remove and clean it.| The rolling brush may be entangled with foreign matters. Please remove and clean it, its connections, its cover, and the suction inlet.
Error 5: The robot is trapped. Please clear obstacles around.| The robot is trapped. Please clear obstacles around.
Error 6: The robot is trapped. Please move it near its home position to start it.| The robot may be suspended. Please relocate it and start. If the anti- drop sensor is too dirty, it may also cause the fault. Please wipe the anti- drop sensor to eliminate the fault.
Error 7: A wheel is suspended. Please move it to near its home position to start it.| A wheel is suspended. Please move it to near its home position to start it.
Error 8: The battery level is too low, and the robot is about to shut down automatically. Please charge it.| The battery level is too low, and the robot is about to shut down automatically. Please charge it.
Error 10: Optical flow sensor dirty, Please wipe it.| The optical flow sensor is covered by dust. Please wipe it.
Error 11: The recharge sensor is blocked. Please wipe it.| The recharge sensor is covered by dust. Please wipe it.
Error 12: The follow-wall sensor is blocked. Please wipe it.| The follow-wall sensor is blocked. Please wipe it.
Error 13: The robot is tilted. Please put the robot on the horizontal ground to start.| The robot is tilted during startup. Please put the robot on the horizontal ground to start.
Error 14: Please install the dust box and filters back.| Please install the dust box and filters back, and make sure that the filters and the dust box are installed in place. Then please restart the robot.
Error 17: Restricted area detected. Please relocate it to start.| The robot is too close to a restricted area during starting. Please relocate it to start.
Error 18: The laser cover is stuck. Please check.| The pressure sensor for the laser cover is pressed or stuck. Please relocate it to start.
Error 19: The laser sensor is stuck or twisted, please check.| The laser distance sensor is stuck by foreign matter. Please clear it.
Error 20: The laser sensor may be blocked, please check.| The laser distance sensor is blocked, please clear the blocking. Too spacious environment and multi-reflection environment such as metal mirrors also affect the normal operation of a laser distance sensor. Please relocate it to art.
Error 21: Please clear obstacles around the charging dock.| The robot may be stuck or trapped. Please clear obstacles around the robot.

The languages NL, PT, RO, BG, CS, SK, UK, SR, HR, EL, BA, and HU are included in the safety instructions.

Straight line test
For measuring dust collection performance in accordance with IEC 62885-7, testers can activate the straight-line test by using the remote control feature in the app menu.

2220003861/02

Documents / Resources

| Rowenta RR7987 X-Plorer Serie 95 Robot Vacuum Cleaner [pdf] User Guide
RR7987, X-Plorer Serie 95 Robot Vacuum Cleaner
---|---

References

• Rowenta USA | Garment Steamers, Steam Irons & Humidifiers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>