GERMiD BV-096B-2K 9.66-Inch 2K HD Streaming Media Mirror Monitor With Built-In Dash Camera User Manual
- June 5, 2024
- GERMiD
Table of Contents
GERMiD BV-096B-2K 9.66-Inch 2K HD Streaming Media Mirror Monitor With
Built-In Dash Camera
PACKING LIST
- Steaming media dash cam
- Dash cam power wire (cigarette lighter version) 2-1. Dash cam hard line (optional)
- Rear camera
- Rear camera power line
- User manual
- Bandage
PRODUCT FEATURES
- 9.66 inch full dispaly screen
- 1080P rear recording
- 2K front recording
- Wi-Fi connect
- HD night version
- Backup camera display
- parking monitor
- Car on auto record
- Waterproof rear camera
- Loop recording
- Time-lapse recording (optional)
- G-sensor
PRODUCT SPECIFICATION
Front camera: IMX335, 5 million Pixel| Front lens
resolution: 25601440 or 19201080
---|---
Storage: 8~64GB, CLASS10 U1, SD card| Rear lens resolution:
19201080
Display screen: 9.66 inch, 1280320| Video compression:
H.264 / H.264
G-sensor: Support| Video format: MP4
Microphone: Built-in| Power supply: USB 5V 2A
Wi-Fi: support| recording angle: front 1300, rear 1400
Backup camera display: support| Working current: 2A
Parking monitor: support| Operating Voltage: DC5V
BATTERY: 800 mAh| Operating temperature: -20 0C~+70 0C
PRODUCT INTRODUCTION
EQUIPMENT INSTRUCTIONS
- TF memory card slot
- Rear camera interface
- USB power interface
- System reset button
- Front HD lens
- speaker
- Power button (short press to turn on / off the screen, long press to turn on / off the mirror)
RECORDING INTERFACE
- The red light ashing indicates the device is recording. When the recording is stopped, the red light disappears.
- Recording resolution display of front lens
- Recording time
- Date and time display
- Wi-Fi status display
- The rear camera connected or not
- Recording sound or not
- Battery status display
- Video sound on / off
- Switch to photo mode (only available when you stop recording)
- Start / stop recording
- Enter the setting interface
- Lock the current recording video
- Drag up and down on the 1/3 of left screen to adjust the display area
- Swipe from left to right to enter the video playback interface
- In the 1/3 of middle screen, slide from top to bottom to enter the setting interface
- Swipe from right to left to switch the front and back display screen ( this function is only available when the rear camera is connected)
- Drag up and down at the 1/3 of right screen to adjust the screen brightness (this function is only available if “Backlight Adjustment” is set to “Manual”)
**CAMERA INTERFACE
**
VIDEO PLAYBACK INTERFACE
HOW TO WIRE
MENU SETTING
In the main interface, short press the button to enter the system menu setting
interface.
- Resolution: 2K + 1080P or 1080P + 1080P .
- Loop Record: 1 minute / 3 minutes / 5 minutes.
- Time-lapse: “Off” “1S” “2S” “3S”. When “OFF” is selected, the device will shut down automatically when the ACC is disconnected. Select “1S”, “2S”, and “3S”: When ACC is disconnected, the device will automatically enter the time-lapse monitoring state and record as “1S frame”, “2S frame”, and “3S frame”. After the ACC is powered, the device exits the time-lapse monitoring and starts normal recording. (This function can only be used when the wire is hard line , and this function cannot be used when power by cigarette lighter)
- Record Audio: On / off can be set; when set to “Off”, there will be no sound in recording video.
- G-Sensor: Off / High / Medium / Low can be set; when gravity sensor is turned on, the machine is subjected to collision during normal recording. When the collision acceleration value reaches the value set by G-Sensor (trigger sensitivity can be set as required), then the system will Lock the currently recorded video, and the locked video will not be covered by the loop system.
- Parking Monitor: Off / High / Medium / Low can be set; when the dash cam is off, if it detects vibration of the car (trigger sensitivity can be set as required), then the recorder will automatically start recording for 20 seconds and then shut down.
- License: You can set your license plate number and then display it on the recording interface and the recorded video.
- Screen Saver: Off / 1 minute / 3 minutes.
- Backlight adjustment: Manual / Auto can be set; when set to manual, it can be adjusted up and down on the 1/3 part of right screen to adjust screen brightness.
- Video Encode: H.264 / H.265 can be set.
- Frequency: 50Hz / 60Hz.
- USB Mode: Connect the device to the PC with a USB wire and directly read the data in the machine’s SD card.
- Key Sound: On / off can be set.
- Speaker: Off / low / medium / high.
- Boot sound: On / off can be set.
- Stream: On / off can be set. Stream mode means the mirror screen display the rear camera as default while you restart the vehile everytime . If switch off the stream mode . The mirror will display the front view camera instead once it power on .
- Language: 8 languages optional.
- Time setting: time / date / time format / date format can be set.
- Format: If there in the SD card are not important, user can clear all themes in the SD card with one click.
- Default: After multiple custom settings, users can use this option to restore the recorder to the original factory setting.
- Wi-Fi App: Scan the QR code to download the APP, and realize the wireless connection between the mobile phone and the device through Wi-Fi.
- Version: Check the device version number.
WI-FI CONNECTION
Built-in Wi-Fi module, this machine can be connected to mobile phone through Android or IOS APP, please follow the instructions below.
- Search “RoadCam” in the App store (Apple) or App Store (Android), or scan the QR code below to quickly install the APP
- urn on the Wi-Fi of the mobile phone, and connect the Wi-Fi ID (the default name is himcapxxxxxxxxxx *), enter the initial password: 12345678.
- Click the icon to connect the phone and dash cam.
- After connecting successfully, on the bottom right corner of the dash cam will display “Please operate in the App!” Users can view the video being recorded or make other settings on the mobile phone.
- Click to enter the recorded video interface, you can perform individual, batch deletion, or download to the local on the recorded video.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>