PEREL EDM1 Wireless Doorbell Kit User Manual

: June 5, 2024
: PEREL

Table of Contents

PEREL EDM1 Wireless Doorbell Kit
Introduction
General Guidelines
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PEREL EDM1 Wireless Doorbell Kit

RED Declaration of Conformity
Hereby, Velleman Group nv declares that the radio equipment type [EDM1]+ [EDMTW] + [EDMTWR] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.velleman.eu.

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

| Keep this device away from children and unauthorized users.
Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
---|---
****| Use the receiver indoors only. Keep away from rain, moisture, splashing and dripping liquids.

General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from dust and extreme temperatures

Protect this device from shocks and abuse. Avoid brute force when operating the device.

Familiarise yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons.
Damage caused by user modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
Due to constant product improvements, the actual product appearance might differ from the shown images.
Product images are for illustrative purposes only.
Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
Keep this manual for future reference.

Battery
Refer to the illustrations on page 2 of this manual.

Transmitter

Open the transmitter to reveal the battery compartment. Use a flat-head screwdriver.
Install the CR2032 battery according to the correct polarity.
Close the battery compartment. Proceed with the installation.

Receiver

Open the receiver to reveal the battery compartment.
Install 3 x 1.5 V AA batteries according to the correct polarity.
Close the battery compartment. Proceed with the installation.

Remark: Remove the batteries if the transmitter and receiver will not be used for a longer period.

CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
Do not puncture batteries or throw them in fire as they may explode. Do not attempt to recharge non-rechargeable batteries (alkaline). Dispose of batteries in accordance with local regulations. Keep batteries away from children.

Installation

Test the operating range between the receiver and the transmitter. The operating range is 150 m in the open air, but may be less due to walls and other obstructions such as PVC or metal frames.

Refer to the illustrations on page 2 of this manual.

Transmitter

Carefully open the housing of the transmitter and use the back plate as a template. Mark the drilling holes at the required height.
Drill the holes using a drill and the appropriate drill bit (not included).
Insert a nylon plug (included) into each hole.
Fix the back plate with the included screws. Click the front plate onto the back plate.
Simply plug the receiver into the mains.

Receiver

Choose the installation spot for the receiver.
The receiver can be fixed to a wall using a hook or nail [2].
Remark: You can also fix the transmitter using double-sided tape.

Operation
Refer to the illustrations on page 2 of this manual.

Make sure both the receiver and transmitter are powered.
The receiver will ring when the button on the transmitter [1] is pressed.
Select the melody with the melody selector [4] and adjust the volume with volume control button [3].

Pairing

On the receiver, hold the button pressed for 5 seconds until youm hear a “ding-dong” sound.
Now, press the transmitter button. The transmitter emits a“ding” sound to confirm successful pairing. The receiver emits a “ding-dong” sound when it exits the pairing mode.

Technical Specifications

frequency …………………………………………. 433.95 MHz
max. RF power …………………………………………. 10 mW
wireless ………………………………………………………. yes
operating range ………………………… 150 m in open area
self-learning …………………………………………………. yes
bell push…………………………………… with LED indicator
number of sounds …………………………………………… 32
IP rating (transmitter) …………………………………… IP44
power supply
transmitter ……………………………. 1 x CR2032 (incl.)
receiver ………………………….. 3 x 1.5 V AA (not incl.)

Use this device with original accessories only. Velleman Group nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.

© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman Group nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.

Velleman® Service and Quality Warranty
Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer Products (for EU):

All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.
Not covered by warranty:
- all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;
- consumable goods, parts or accessories that are subject to an aging process during normal use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber parts, drive belts… (unlimited list);
- flaws resulting from fire, water damage, lightning, accident, natural disaster, etc.…;
- flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer’s instructions;
- damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of the article;
- all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.
Articles to be repaired must be delivered to your Velleman® dealer, solidly packed
(preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
Hint: In order to save on cost and time please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
Repairs occurring after warranty expiration are subject to shipping costs.
The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article (see article’s manual).