PASCO PK-9031B Conductive Ink Pen User Guide

Conductive Ink Pen
PK-9031B
Product Guide
012-04297E

About the Product

This is a disposable pen containing silver conductive ink. A line of silver ink has a resistivity of 50 to 125 μΩ·cm. Using the pen in conjunction with PASCO conductive paper  (PK-9025B and PK-9026) produces an insignificant voltage drop across the line. The paper has a resistivity of approximately 5000 Ω/square. The ink pen yields approximately  200 feet of continuous line and has a shelf life of approximately six months.

Notes

• Before using, shake the pen vigorously with the cap on to disperse particles suspended in the ink.
• Press the tip lightly against the paper and squeeze the barrel while writing.
• Allow 3 to 5 minutes for the ink to dry at room temperature. Maximum conductivity requires 20 minutes of drying.
• After each use, close the cap tightly on the pen to keep the ink from drying.
• Store the pen in a refrigerator to maximize the shelf life.

Technical Suppor

Need more help? Our knowledgeable and friendly Technical Support staff is ready to provide assistance with this or any other PASCO product.

Warranty, Copyright, and Trademarks

Limited Warranty
For a description of the product warranty, see the Warranty and Returns page at www.pasco.com/legal.
Copyright
This document is copyrighted with all rights reserved. Permission is granted to non-profit educational institutions for the reproduction of any part of this manual, providing the reproductions are used only in their laboratories and classrooms, and are not sold for profit. Reproduction under any other circumstances, without the written consent of PASCO scientific, is prohibited.

Trademarks

PASCO and PASCO scientific are trademarks or registered trademarks of PASCO scientific, in the United States and/ or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of, their respective owners. For more information visit www.pasco.com/legal.

For the complete SDS go to: https://www.chemtronics.com/sds-tds
Search Term: CW2200

SAFETY DATASHEET

CircuitWorks Conductive Pen

‘Section 1. Identification
GHS product identifier: CircuitWorks Conductive Pen
Product code: CW2200 STP, CW2200MTP
Other means of identification: Not available.
Product Type: Liquid.
Relevant identified uses of the substance or mixture and uses advised against
Not applicable.
Supplier’s details: Chemtronics 8125 Cobb Center Drive Kennesaw, GA 30152 Tel. 7704244888 or toll-free 800-645-5244
Emergency telephone number (with hours of operation) : Chemtrec – 1-800-424-9300 or collect 703-527-3887 24/7
Section 2. Hazards identification
OSHAIHCS status: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Classification of the substance or mixture : FLAMMABLE LIQUIDS – Category 2 ACUTE TOXICITY (inhalation) – Category 4 EYE IRRITATION – Category 2A
GHS label elements Hazard pictograms: Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 55%
Signal word: Danger
Hazard statements : Highly flammable liquid and vapor. Harmful if inhaled. Causes serious eye irritation.
Precautionary statements Prevention : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking. Use explosion-proof electrical, ventilating, lighting, and all material-handling equipment. Use only non- sparking tools. Take precautionary measures against static discharge. Keep the container tightly closed. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling.
Response : IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
Storage: Store in a well-ventilated place. Keep cool. Dispose of contents and container in accordance with all local, regional, national and international regulations.
Disposal : Date of issue/Date of revision:11/7/2018 Date of the previous issue:11/62018 Version :3 1/131

Section 2. Hazards identification Occu’Works Conductwe Pen

Hazards not otherwise: None known.
classified

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of: Not available.
identification

112-07-2

Any concentration shown as a range is to protect the confidentiality or is due to batch variation.
There are no additional ingredients present that, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.
Section 4. First-aid measures

Description of necessary first aid measures

Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.
Inhalation: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If necessary, call a poison center or physician. If unconscious, place in the recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt, or waistband.
Skin contact: Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Wash clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion: Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If the material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in the recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt, or waistband.
Most important symptoms/effects, acute and delayed Potential acute health effects

Eye contact:  Causes serious eye irritation.
Inhalation: Harmful if inhaled. It
Ingestion: Skin contact: May cause skin irritation.
Do not ingest. If swallowed then seek immediate medical assistance.

Over-exposure signs/symptoms
Eye contact: Adverse symptoms may include the following: pain or irritation watering redness
‘Date of issue/Date of revision :11/7/2018 Date of the previous issue:11/61018 Version :3 2/131
For the complete SDS go to: https://www.chemtronics.comisds-tds Search Term: CW2200
www.pasco.com

References

• Support Center | PASCO
• PASCO scientific | Science Lab Equipment and Teacher Resources
• Privacy Policies | PASCO
• Support Center | PASCO
• Chemtronics SDS and TDS Documents | Chemtronics

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>