iLive Bluetooth Sports In-Ear Headphones-Complete Features/Owner’s Guide

: June 5, 2024
: iLive

Table of Contents

iLive Bluetooth Sports In-Ear Headphones
Specifications
Introduction
Features
Includes
Battery Charging
Orientation & Controls (Right Earbud only)
Initial Bluetooth Connection
Speakerphone
Previously Connected Devices
Troubleshooting
Customer Support
FCC Warnings
Additional Warnings
FREQUENTLY ASKED QUESTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iLive Bluetooth Sports In-Ear Headphones

Specifications

BLUETOOTH VERSION: 0
DRIVER: 10mm
FREQUENCY RESPONSE: 20Hz – 20kHz
NOMINAL IMPEDANCE: 16ohms
SENSITIVITY: 106dB+/-3dB
WIRELESS RANGE: 33 feet
CHARGE TIME: 120 minutes
BATTERY LIFE: ~4 hours at 100% volume

Introduction

The iLive In-Ear headphones have a number of features with the most prominent being the Bluetooth version 5.0 connectivity. They come with a built-in mic and are sweatproof. They have a driver of 10mm which provides good sound quality. They have an LED indicator to show the power and pairing mode. The earbuds also feature a voice prompt. They can be charged using the provided micro-USB cable. The Bluetooth connectivity range of the earbuds is about 33 ft.

Features

Rubberized coating
Sweatproof
Bluetooth Wireless: range 33 ft.
Active noise cancellation
Built-in microphone
Voice prompts announce earbud operations
Digital volume control
Built-in rechargeable battery: approximately 4 hrs. playtime
Micro-USB port for battery recharge

Includes

3 pairs of ear tips: 1 small, 1 medium, 1 large
Micro-USB to USB charging cable

Battery Charging

Pull back the cover on the DC Power Input.
Using a Micro-USB to USB cable, connect to the USB port of a powered-on computer or USB power adaptor (not included).

Initial charge time is approximately 2 hours. Charge fully before use.

When the battery is low an indicator LED will flash red for 1 minute and a voice will announce “Low Battery,” then the unit will automatically power OFF.
While the unit is charging it will display a solid red light. When the unit is fully charged it will display a solid blue light.

Orientation & Controls (Right Earbud only)

Initial Bluetooth Connection

With the earbuds powered OFF, press and hold the power button until they power ON and the voice prompt says “Power on…Bluetooth is connecting.” When pairing, remain within 3 feet of the Bluetooth device.
Using the controls on your Bluetooth device, select IAEB29 in the Bluetooth Settings to pair. If need be, refer to the user’s manual for your specific device for more information.
When successfully paired, a voice will announce “Bluetooth is connected” and the LED indicator will blink twice every few seconds. Audio from the connected Bluetooth device will now be heard through the earbuds.
Use the controls on the connected Bluetooth device to select and play audio. Use the earbud controls or the connected Bluetooth device to play, pause, and adjust the volume level.
After initial pairing, press and hold the power button until the voice prompt says “Power on.” The earbuds will power ON and automatically connect to the Bluetooth device.

Speakerphone

To accept a call, press the power button, or use the controls on the connected phone.
To end a call, press the power button, or use the controls on the connected phone.
To re-dial the last dialed number, press the power button twice.

Previously Connected Devices

The earbuds can remember multiple Bluetooth devices and will always try to reconnect to the last device used.
To re-connect to a different device, turn off Bluetooth on unwanted devices, then access the Bluetooth settings menu on the device you wish to use and select IAEB29.

Troubleshooting

If the earbuds should become unpaired or will not connect normally, follow these steps in your device’s Bluetooth Settings Menu.

Delete the earbuds (“Forget This Device”).
Turn Bluetooth OFF then ON again, and repeat the Initial Bluetooth Connection steps.

Customer Support

Customer Service: 1-888-999-4215 | Email Support: prodinfo@ dpiinc.com | Email Parts: partsinfo@dpiinc.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com
To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at: www.iLiveElectronics.com

FCC Warnings

WARNING
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

WARNING: To prevent fire or shock hazards, do not expose this unit to rain or moisture.
WARNING: Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable.
Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of according to state and local guidelines. They should never be disposed of in normal household waste, and they should never be incinerated, as they might explode. Contact your local government for disposal or recycling practices in your area.
To avoid hearing damage, make sure that the volume on your music player is turned down before connecting your headphones. After placing headphones in/on your ears, gradually turn up the volume until you reach a comfortable listening level.

WARNING
This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov This product meets and complies with all Federal regulations.

FREQUENTLY ASKED QUESTIONS

Is iLive a good brand for headphones?
Yes, iLive is a good brand of headphones, they have good sound quality and a long battery life.
How do you put iLive headphones in pairi ng mode?
They can be put in to pairing mode by pressing and holding the Power/Pair button for 7 to 9 seconds.
How long does it take ILive earbuds to charge?
The iLive earbuds take about 2 hours to charge completely.
How do I reset my ILive earbuds?
This can be done by pressing the power button for 15 seconds and then forgetting the headphones from your device paired list. Re-pair the headphones to your device.
How long do iLive wireless earbuds last?
When fully charged the iLive earbuds last for about 4 hours.
Can you overcharge a Bluetooth headset?
No, they stop charging once their battery is full.
How do you connect both earbuds at the same time?
The two Bluetooth headsets must be paired at the same time; otherwise, only one will pair.
How often do you need to charge Bluetooth headphones?
When the Bluetooth headphones arrive, their battery isn’t fully charged. To fully activate the battery.
What is the connectivity range of the Bluetooth headphones?
The Bluetooth headphones have a connectivity range of about 33 feet or 10 meters.
Is their indicator to tell about the pairing mode?
Yes, the headphones have an indicator to tell about the pairing mode.