tp-link Tapo S200B Smart Button User Guide
- June 5, 2024
- tp-link
Table of Contents
Quick Start Guide
7106509202 REV1.0.0
Meet Your Smart Button
Control lights, appliance, and other connected devices at the touch of a
button. Smart Button can also be an instant trigger for Tapo Hub.
Before You Start
A Tapo Hub is required. Make sure your Tapo Hub is successfully added via the
Tapo app.
https://www.tapo.com/app/download-app/
Power Up Your Button
Remove the battery insulation tab to power up your button. The LED should
blink.
Note: If the LED is not blinking, refer to the back page to reset it.
Set Up Your Button
Open the Tapo app, tap the + button in the app, and select your model.
Follow app instructions to complete the setup.
Test Your Button
Press the button to test it. Make sure the Tapo app shows the button is tapped when you press it.
Secure Mounting Bracket
Once you’ve decided on a location, secure the mounting bracket with either the
included screws or the attached tape.
Mount Your Button
Place the button on the bracket posts, and the button will be magnetically attracted.
How to reset button to enter paring mode
a. Press and hold the button for 5 seconds. The LED will become yellow-green
for 10 seconds.
b. Press the button 3 times within that 10 seconds.
c. The LED should start blinking.
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
CAUTION!
Risk of explosion if the battery is replaced by an incorrect type Avoid
replacement of a battery with an incorrect type that can defeat a safeguard.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that
may result in an explosion or the leakage of flammable liquid or gas. ©2022
TP-Link
For
technical support, the user guide and more information, please visit
www.tapo.com/support/
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter.
End-users and installers must be provided with antenna installation
instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Need some help?
Visitwww.tapo.com/support/
for technical support, user guides,
FAQs, warranty & more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>