pokitter ‎T2 MAX Ultra Compact Projector User Manual

PORTABLE PROJECTOR

User Manual

Please read through this manual in detail before using

Thanks for ordering our company’s product, please read this manual throughly before using for the sake of your safty and interests. We assumes no responsibility for any personal injury, loss of property or others that caused by inappropriate operation if you don’t follow the instructions stated hereof.

Important Safety Precautions

The following safety instructions will ensure long service life of the machine, and avoid any fire or electric shock. Please ensure to read carefully and pay high attention on all the following warnings

Don’t install in places with poor ventilation

Don’t install in places that hot and humid

Don’t block the vent
(Inlet or Outlet)

Don’t install in dusty and smoky areas

Don’t install close to any temperature or smoking sensors
(May cause sensors failures)

Don’t install in areas that directly blown by cold and warm wind of air conditioner
(Otherwise, it may cause failure due to vapor condensation or rise of temperature)

Pay Attention to Heat Dissipation

Please leave at least 30cm between projectors and objects around to maintain projectors’ performance and reliability

Attention

Please avoid watching lens directly so as to prevent our eyes from being hurt as projectors are with very high brightness

Packing List

Please check if any accessory is missing when opening, please contact your distributor if it has any shortage

| |
---|---|---

Projector

| Remote Control|

Power Line

|

User Manual

Basic Parameters

Product Brief

Please check projector components and functions before using

1. Back
2. Up, Down, Left, Right
3. Focus Wheel
4. Keystone Correction
5. Remote Control Signal Receiving Window
6. Lens
7. HDMI Interface
8. ON/OFF
9. USB interface

Remote Control

1. Signal Source (Multimedia) / Mouse Mode (Android)
2. Multi-Function Keys
3. OK
4. Return
5. Volume+
6. Volume –
7. Home
8. Next
9. Previous
10. Arrow keys
11. OFF/ON

Projection size / Distance

Projection size
(inch, no keystone correction)

| Screen
*length width (m)**|

Lens ~ screen (m)

---|---|---

50

| 0.67×1.11| 1.50
72| 0.98×1.59|

2.00

84

| 1.10×1.86| 2.50
100| 1.36×2.21|

2.84

120

| 1.65×2.66|

3.50

Installation and Adjustment

1 Installation

You can place horizontal or via hanger installation.
Note: hanger is non-attached accessory!

Horizontal Placement     Hanger Installation

2 Adjust Focal Length

1. Keystone Correction Loop
2. Focus Wheel

Keystone Distortion

Diagram 1

Blurred Distortion

Diagram 2

Achieve satisfactory picture imaging effect via adjusting the keystone correction loop and focus wheel on the machine.
When keystone distortion occurs (as per diagram 1), it is recommended to adjust the keystone correction loop; when the image is blurred (as per diagram 2), it is recommended to adjust the focus wheel to improve picture clarity.
If satisfactory clarity can not be achieved followed steps above, please move the product forward or backward as appropriate.

3 Shutdown Safely

1. Press the button on the remote control to turn off the machine
2. Press the button on the back of machine body to turn off the machine.

Note: Please pull out the plug in time to save energy once the machine is turned off.

Mobile phone screen/same screen

Connect with IOS Phone:
WAY1:

1. Click WiFi and find “WANBO X1-xxxxxx”, then input password “12345678” on your iPhone.
2. Click “Screen Mirroring”on your iPhone.

WAY2:

1. Click “OK” on the remote control, connect home WiFi; Then connects the same WiFi on your iPhone.
2. Click “Screen Mirroring” on your iPhone.

Connect with Android:

1. Click “Wireless Projection” on your phone.
2. Select “WANBO X1”, complete screen sharing.

Connect by Cables:

1. Connect iPhone and projector through “USB” port with Phone USB cable.
2. Click “Trust”.

Projection Setting Function details (Android)

Installation Mode
There are four installation modes (Front Projection, Rear Projection, Rear Projection Lifting, Front Projection Lifting). Users can choose installation mode by pressing the left and right direction keys of the remote control, and install the projector as you like.

Keystone Correction
Keystone correction includes four-point keystone correction and vertical keystone correction. Users can choose four-point keystone correction or vertical keystone correction by pressing the confirmation key or left and right direction key on the remote-control under keystone correction option.

Under the four-point keystone correction option: select manual keystone correction, press confirmation key in the remote control to enter the manual keystone interface, then operate according to the screen prompts.

Under the Vertical Keystone Correction option: Screen option shows infinite zoom and manual keystone correction, infinite zoom can reduce or enlarged screen with an adjustment range between 80% and 100%. Manual Keystone Correction adjusts value through left and right direction keys of the remote control to ensure pictures to be the best.

WIFI Connection Description: Enter setting option, click Network Settings, open the WIFI setting switch, select the network required. If no WIFI displayed, we can search and add WIFI manually.

Bluetooth Connection Description: Enter setting option, click Bluetooth setting, open the Bluetooth switch, choose Bluetooth device to match (Note: Bluetooth can connect audio only but can not connect mobile phone.

Clarity Adjustment: Adjust focus first and then adjust distance of placement if not clear.

Mobile Phone Projection / Same Screen (Android Version)

Firstly, make sure Projector and mobile phone under the same WiFi, open Eshare of the projector, and then open video apps in your mobile phone (such as Youtube, Netflix), click TV icon in the upper right corner of the video to project).
iPhone uses Airplay mirror for same screen and projection; Android phone can project directly with Eshare, Android computer can download Eshare or use HDMI cable to complete projection.
Note: The above operations need to be done under the same WIFI, all devices should connect to the same WIFI (wireless network).

System upgrade (Android Version)

Upgrade online
Online update through system upgrade.

U disk upgrade (Local upgrade)
Copy the upgrade firmware to U disk root directory in FAT32 format, insert the U disk into the USB interface of projector, then select U disk upgrade.

Mandatory upgrade
Copy the upgrade firmware to U disk root directory in FAT32 format. Insert the U disk into the USB interface under turn off condition of the projector, meanwhile, long press the device power button for 5 seconds to start automatic upgrade.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>