InvisQi Invisible Wireless Charger Installation Guide
- June 5, 2024
- InvisQi
Table of Contents
InvisQi
User Instructions and Installation Guide
IN THE BOX
- InvisQi charging unit
- InvisQi mount plate
- User instructions
- Qi-charging sticker
- Supplementary green silicon-wafer tester
- 3M adhesive strips
- InvisQi charger
- Screws
BEFORE BEGINNING THE INSTALLATION ENSURE THE FOLLOWING
- If you have a phone case please ensure it is flat and does not contain any metal, centrally located magnets, cardholders, pop sockets, or kickstands.
- The table or surface being used is flat and does not exceed 20-30mm in thickness.
STAGE 1 – CHARGER INSTALLATION
-
Measure your table or surface’s thickness to determine whether it can be used with the InvisQi charging unit.
-
Choose the ideal spot on the table or surface and place your supplementary Qi-charging sticker for reference.
-
Attach the 3M adhesive strips to the InvisQi mount plate and align the plate directly under your Qi-charging sticker.
-
Affix the dock plate directly under the Qi-Charging sticker and mount the InvisQi charging unit face up (with the Iraqi logo facing upwards or on the underside of the table).
-
Connect the power cord to your InvisQi charger and use the supplementary green silicon-wafer tester to test the connection. If one or more lights flash when the tester is placed on the Qi-charging sticker then the installation has been completed successfully and your InvisQi charger is ready for use.
-
Place your device faces up aligning the center of your phone to the center of the sticker and begin charging! For better results, please remove the phone from the charging spot and wait 2-3 seconds before repositioning.
TROUBLESHOOTING AND FAQS
Please email admin@invisqi.com for all other questions and queries.
Why is my phone not charging?
Please ensure: If you have a phone case, it is flat and does not contain any
metal, centrally located magnets, cardholders, pop sockets, or kickstands.
Ensure your phone is aligned as centrally as possible. Check if your phone is
Qi-wireless charging enabled. Check your sticker position through
recalibration. Check your table or surface thickness is within the stated
performance range.
Why has my phone stopped charging?
The InvisQi Wireless Charger is designed to recognize and react to temperature
changes within your phone which can occur after extra long charging periods of
3 hours or more. In these instances, the charger may enter a standby mode to
allow your device to cool if required by your phone until the device requests
more power. This feature ensures better battery health and longevity for your
phone.
Why does my phone feel hot?
Increased phone temperatures during wireless charging are normal especially
during longer charging sessions. Our IQC™ technology is designed to
minimize phone heating however, if your phone is hotter than usual, please
ensure you have aligned it correctly and try again.
Why do the charging speeds vary?
Different phone models have different battery sizes and charging profiles,
therefore, taking different amounts of time to charge, with large batteries
especially taking longer. charging speeds may also slow at ≥80% in IOS models
due to Apple software requirements designed to limit battery deterioration
during wireless charging. The InvisQi Wireless Charger recognizes IOS
charging signals and corresponds by adapting charging speeds until your device
requests more power. Please try turning OFF ‘Optimised Battery Charging’ in
your ‘Settings’. Charging speeds will also vary depending on the surface
thickness. Thicker surfaces will reduce charging efficiency due to the greater
distance the charging signal needs to travel.
SAFETY INSTRUCTIONS
- Avoid contact with water and do not submerge.
- Avoid extreme temperatures.
- Avoid dropping.
- Use original or certified cables.
- Do not clean with corrosive substances or oils.
- Do not disassemble.
- Electronic adapters are recyclable waste and must not be disposed of in the household waste.
- Dispose of this equipment using a designated collection point for the recycling of electrical and electronic equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>