LIDEKA Solar Powerbank 30000 mAh User Manual
- June 5, 2024
- LIDEKA
Table of Contents
LIDEKA Solar Powerbank 30000 mAh
Introduction
This wireless solar energy power bank supports QC2.0/QC3.0 output voltage fast
charge protocol, FCP/AFC/SFCP output voltage and input voltage fast charge
protocol, MTK PE + 1.1 & 2.0 output voltage fast charge protocol,
USB-C/PD2.0/PD3.0 input voltage and output voltage protocol, USB C PD3.0 PPS
output voltage protocol and is suitable for BC1.2 mobile Apple and Samsung
devices.
The product features a micro-USB charging port, TYPE-C interface and solar
power input power. The built-in lithium-ion battery is charged from a constant
current and voltage source. The power bank supports multiple electronic
devices including mobile phones, tablets, MP3 devices and more. USB-2, USB-3
and USB-4: standard output 5V/3A USB-1: Supports QC2.0/QC3.0 DC5V/3.0A 9V/2A
12C/1.5A TYPE-C: supports PD2.0/PD3.0 PPS FCP AFC SFCK MTK bi-directional fast
charge protocol USB-1 and TYPE-C are fast charging USB ports. Output voltage
of 5V is only supported when two or more output ports are used at the same
time. This device is equipped with the latest technologies in fast charging
and thus achieves an efficiency of 90% and an extremely low energy
consumption. With smart techniques, the device offers multiple protection
functions and the power bank is safe and reliable in use.
Specifications
- Micro input: DC 5V/2A 9V/2A
- TYPE-C input: DC 5V3A 9V2A
- Solar charging: DC 5V/1.5W
- USB-1 output voltage: DC 5V/3.0A 9V/2A 12V/1.5A
- Output voltage USB-2, -3, -4: DC 5V/3A
- TYPE-C output voltage: DC 5V/3.0A 9V/2A 12V/1.5A
- Wireless output voltage: 10W
Display functions
- Solar panel
- Cord
- Solar indicator
- USB port 1/2/3/4
- USB silica gel protect plug
- Micro/TYPE-C USB port
- Power indicator
- On/off button
- LED lamp
- . Wireless charging indicator
- . Wireless charging point
Switching on and off
Switch the device on with the on/off button to activate the wireless charging
point and all USB ports. When the red light flashes
three times, the power bank is ready to be used and the charging process
begins. The light will turn green when an external device is detected. When
the device is fully charged and the charging process
is complete, the light turns off.
Charging with adapter
When an external adapter is connected to a USB or TYPE-C input, the built-in
battery of the power bank is charged. Four blue lights turn on automatically
and provide an indication of battery power as follows:
Charging with solar panel
Place the power bank at an angle of 45 degrees to optimally expose the solar
panel to sunlight. The built-in charging circuit turns on and the lithium
battery is charged. Use the on/off button to view the stored power (this can
be displayed as “Power View”).
Battery indication
Briefly press the power button to enable the USB ports. The LED power
indicator shows the available battery power according to the table below. The
USB ports are automatically turned off if no input is detected within 30
seconds.
Wireless charging
When the wireless charging function is used, a desired device can be charged
with a maximum output voltage of 10W. When all USB ports are used at the same
time or when the current falls within a range of 2.5A, the wireless charging
function will automatically switch to 5W. The charging function is completely
switched off at a
range of 3A.
Instructions LED lamps
Press the button twice to turn the LED lights on or off and short press the button to change light settings (soft light, bright light, flashing light, SOS mode).
Protection functions
Input voltage and voltage undercurrent protection
When an adapter with different specifications (less than 5V/2.1A) is used for
charging, the power bank will automatically be adjusted to the output voltage
of the adapter used to prevent damage. The device does not support output
voltage discharge power while charging, but it does while charging via a solar
panel.
Input voltage short-circuit protection
If a short circuit occurs due to improper use or a damaged adapter, for
example, the device will automatically shut down to prevent product damage.
Output voltage overcurrent protection
When the output voltage of any of the USB ports is exposed to more than 3.2A,
the power bank will turn off automatically to protect both devices (power bank
and external device). The power button light indicator will be switched off
after four flashes. The device must be recharged and activated to start the
discharge process.
Output voltage short-circuit protection
When a short circuit occurs within one of the USB ports, the device will
automatically shut down to protect both devices (power bank and external
device). The power button light indicator will go out after four flashes. The
device must be reactivated and charged to start the discharge process.
Warnings
- Do not expose the device to high ambient temperatures for a long time. Maximum 45 degrees. (which occurs, for example, near radiators or stoves). Don’t put it in the sun for too long either. Overheating will damage the device and is associated with potential danger.
- This product consists of electrical components. To avoid danger and damage, never disassemble this appliance.
- This device contains lithium-ion batteries. Please take into account your local regulations and legislation regarding the disposal and recycling of batteries.
- Never expose removed batteries to excessive heat and keep them away from sunlight and fire.
- Be absolutely patient with solar and power grid charging. The power bank has a very high capacity and therefore needs time.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>