SONY VPL-VW890ES Home Cinema Laser Video Projector Owner’s Manual
- June 5, 2024
- Sony
Table of Contents
Video Projector
Quick Reference Manual
VPL-VW890ES
Printed in China
© 2021 Sony Corporation
About the Quick Reference Manual
This Quick Reference Manual explains the installation and basic operations
for projecting pictures. Before operating the unit, please read this manual
thoroughly and retain it for future reference. Refer to “About Indicators” as
necessary. For details on the operations, refer to the Operating Instructions.
Downloading Manuals
Manuals that describes how to operate the unit can be downloaded from the Sony
website. Download the required manual by accessing the site using the
following QR code or URL.
https://rd1.sony.net/help/vpl/vw890/h_zz/
Manuals are in PDF format. PDF files can be viewed on a computer with Adobe Reader installed. You can download Adobe Reader for free from the Adobe website.
Preparing
Checking the Supplied Accessories
Check the carton to make sure it contains the following items:
- Remote control RM-PJ24 (1) · Size AA (R6) batteries (2)
- AC power cord (1)
- Quick Reference Manual (this manual) (1)
- Safety Regulations (6)
Inserting the Batteries into the Remote Control
Caution about handling the remote control
- Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind onto it.
- Do not place the remote control in a location near a heat source, a place subject to direct sunlight, or a damp room.
Installing the Unit
-
Position the unit so that the lens is parallel to the screen.
-
After connecting the AC power cord to the unit, plug the AC power cord into a wall outlet.
Note
After connecting the AC power cord to the unit, the ON/STANDBY indicator may blink in orange.
You may not be able to control the unit while the indicator is blinking, but this is not a malfunction. Wait until it stops blinking and remains lit in red. -
Press the (On/Standby) button to turn on the unit.
-
Project an image on the screen, then adjust the focus, size, and position.
-
Adjust the focus.
Press the LENS ADJUSTMENT (FOCUS) button to display the Lens Focus adjustment window (test pattern). Then adjust the focus of the picture by pressing the button. -
Adjust the picture size.
Press the LENS ADJUSTMENT (ZOOM) button to display the Lens Zoom adjustment window (test pattern). Then adjust the size of the picture by pressing the button. -
Adjust the picture position.
Press the LENS ADJUSTMENT (SHIFT) button to display the Lens Shift adjustment window (test pattern). Then adjust to the proper position of the picture by pressing the button.
To adjust the tilt of the installation surface
If the unit is installed on an uneven surface, use the front feet (adjustable)
to keep the unit level.
Notes
- If the unit is tilted up or down, the projected image may be trapezoidal.
- Be careful not to catch your finger when turning the front feet (adjustable).
Lens adjustment window (test pattern)
The dashed lines show the screen sizes of each aspect ratio
Connecting the Unit
When making connections, be sure to do the following:
- Turn off all equipment before making any connections.
- Use the proper cables for each connection.
- Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself.
- Refer to the operating instructions of the connected equipment.
When you monitor and control the projector via the network, access the Setup page of the projector (refer to “Using Network Features” in the Operating Instructions) via a Web browser and enable the desired control protocol.
Projecting
Projecting the Picture
- Turn on both the unit and the equipment connected to the unit.
- Press INPUT to display the input palette on the screen.
- Select the equipment from which you want to display images.
Press INPUT repeatedly or press (enter) to select the equipment from which to project.
Turning Off the Power
- Press the (On/Standby) button. The message “POWER OFF?” appears.
- Press the (On/Standby) button again before the message disappears.
The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat.
The fan stops and the ON/STANDBY indicator changes from flashing green to remaining red.
The power is turned off completely, and you can disconnect the AC power cord.
Note
Never disconnect the AC power cord while the indicator is flashing.
Tip
You can turn off the unit by holding the (On/Standby) button for about 1
second, instead of performing the above steps.
Selecting the Picture Viewing Mode
Press one of the CALIBRATED PRESET buttons.
| Setting items | Description |
|---|---|
| CINEMA FILM 1 | Picture quality suited to reproducing the highly dynamic and |
clear images typical of master positive film.
CINEMA FILM 2| Picture quality suited to reproducing the rich tone and color
typical of a movie theater, based on the “CINEMA FILM 1.”
REF| A picture quality setup suitable for when you want to reproduce
faithfully the original image quality, or for enjoying image quality. without
any adjustment.
TV| Picture quality suited for watching TV programs, sports, concerts, and
other video images.
PHOTO| Ideal for projecting still images taken with a digital camera.
GAME| Picture quality suited to gaming, with well-modulated colors and fast
response.
BRT CINE| Picture quality suited for watching movies in a bright environment,
such as a living room.
BRI TV| Picture quality suited for watching TV programs, sports, concerts, and
other video images in a bright environment, such as a living room.
USER| Adjusts the picture quality to suit your taste then saves the setting.
The factory default setting is the same as “REF.”
Error Handling
About Indicators
The ON/STANDBY or WARNING indicator lights up or flashes if there is any
trouble with your projector.
If there is any problem or an error message appears on the screen, refer to
“Error Handling” in the Operating Instructions.
Flashing/Lighting indicators| The number of flashes| Cause and
Remedy
---|---|---
| Three times| The unit does not light properly due to an abnormality of the
light source and light source power. Turn off, then turn on the power after a
while.
If the symptom persists, consult qualified Sony personnel.
Six times| The unit detects a drop impact.
If there is abnormality on the unit, consult with qualified Sony personnel.
If there are no abnormalities on the unit, disconnect the AC power cord and
check that the ON/STANDBY indicator turns off, then connect the AC power cord
and turn the unit on.
Eight times| The lens is not securely attached. Consult with qualified Sony
personnel.
| Twice| The internal temperature is unusually high. Check to ensure that
nothing is blocking the ventilation holes and the unit is not being used at
high altitudes.
Three times| The fan is broken. Consult with qualified Sony personnel.
Note
If the symptom persists even after carrying out the above methods, consult
with qualified Sony personnel.
If the indicator starts flashing in a way of other than the above, turn off,
and then turn on the power with the (On/Standby) button on the remote control
or control panel of the unit.
If the symptom is shown again, consult with qualified Sony personnel.
If there is any problem or an error message appears on the screen, refer to “Error Handling” in the Operating Instructions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>