Guangdong Hengdi Technology HD22B24G Video Streaming Drone Instruction Manual

Guangdong Hengdi Technology HD22B24G Video Streaming Drone

VIDEO STREAMING DRONE

GETTING TO KNOW YOUR DRONE
PLEASE READ ALL WARNINGS AND INSTRUCTIONS PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS IMPORTANT INFORMATION ABOUT YOUR DRONE.

CHARGING

• The drone must be charged before each use (USB Charge Cable included) Indicator light will turn off once fully charged Install batteries in remote

PAIRING
Before each flight pair the remote with the drone:

1. Turn your drone on and place it on a flat, level surface
2. Turn the remote and move the left joystick up, then down
3. The beep will indicate successful pairing
4. Repeat steps 1 and 2 if necessary

DIRECTIONAL LIGHTS

• White lights indicate the front of the drone and Red lights indicate the back of the drone Not applicable in auto-orientation mode

REMOTE CONTROL OVERVIEW
Practice flying your drone below 1 O feet and at low speeds until comfortable with all controls to avoid damage or injury

• Left joystick:
• Up/Down controls elevation
• Left/Right controls spin
• Bight joystick: controls flight direction
• Direction Trim: use to eliminate drift To cut power to the drone, move the left joystick to the down position

INTRODUCTION

Congratulations on your purchase of the Streaming 2.4 GHz Video Drone. Get ready to soar to new heights. Master the art of drone flying with remote control maneuverability. This lightweight drone will provide hours of fun.

SPECIFICATIONS

• Drone Battery: 650 mAh Li-po
• Remote Controller Battery: 6 x 1.5V AA Charging Time: Approximately 100 minutes
• Maximum Recommended Altitude 120 ft.

SAFETY WARNINGS

• Not recommended for children under 14 years of age. As with all electrical products, precautions should be observed during handling and use to reduce the risk of electrical shock.

• Adult supervision is required at all times.

• Before each use, an adult should review the product and battery to determine that no damage or hazards exist.
  DO NOT TOUCH SPINNING PROPELLERS.

• Do not allow any1hing to intentionally make contact in any way with spinning propellers.

• Prevent contact with spinning blades by turning off the remote prior to handling the drone.

• Use caution and pay attention to your surroundings while operating a drone.

• Do not fly drones into animals, people, or inanimate objects.

• Keep drones away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.

• Do not operate in rain, heavy wind, or any type of severe weather.

• Do not land drones on wet surfaces.

• Never touch or allow others to touch the drone while it is flying.

• Always turn the drone off when it is not in use. Always fly drones in large open areas.

• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.

• Always use caution when flying drone vehicles, obey relevant laws and respect the privacy and property rights of others.

• The drone shall never be modified or used for any1hing except for its intended purpose.
  Note: Wind above a surface is higher than at ground level.

PLEASE RECYCLE OR DISPOSE OF ELECTRONICS PROPERLY RECYCLING INFORMATION IS AVAILABLE AT WWW.MERCHSOURCE.COM

Invasion of Privacy Warning
Always be mindful of others’ privacy and do not record videos or take images of others without their consent. Check and comply with your federal, state and local laws regarding privacy.

CONTENTS

REMOTE BATTERY INFORMATION

1. Slide the open the battery compartment
2. Install 6 “AA” batteries as shown in the diagram shown above
3. Replace and close the battery compartment

£LITHIUM-POLYMER BATTERY WARNING
There is a risk of fire and personal injury if the Li-Po battery is punctured, damaged or misused

• Never expose the battery to extreme temperatures or moisture
• Do not subject the battery to strong impacts
• Always keep the battery away from flammable materials
• Only use manufacturer-specified battery(ies), and charger(s). and/or adapters. if applicable, specified by the manufacturer
• The battery is not serviceable
• Let battery cool to room temperature before charging
• While charging, never leave the battery unattended
• Recycle or dispose of batteries according to federal, state, and local laws KEEP THIS INSTRUCTION MANUAL FOR REFERENCE

BATTERY WARNING

• Do not mix old and new batteries
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal
• Only use manufacturer specified better(ies), charger(s), and/or adapters, if applicable, specified by the manufacturer
• Always use, replace, and recharge (ti apply:able) batteries under adult supervision
  KEEP THE PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION

CHARGING BATTERY

Note: The Battery Charge Cable will light up when it is charging the battery and turn off when the battery is fully charged. Charge time is approximately 100 minutes. Turn off the drone before charging. Connect the Battery Charge Cable to the charging port on the Drone. Connect connector to a power source.

Replacing Propellers

1. Follow diagram
2. Remove screw from the top of Propeller
3. Remove broken Propeller and replace it with a new Propeller
4. Make sure you installed the correct blade. Each blade has a number written on it. Match the blades with the corresponding number on the drone
5. Insert the screw into the top of Propeller

DRONE APP

Connect the Charging Cable to the Drone Go to your app store on your smart phone and download the “360 Mach Flight” application

Pairing Drone – First Time

1. Press the connect to Wi-Fi button
2. Follow the on-screen instructions

After Connecting Drone

1. Press the Stream Button to begin streaming
2. Press the Album Button to review pictures and videos

INSTALLING PHONE HOLDER

• Insert antenna through hale at the base of the Smart Phone Mount.
• Align hole on Mount with hOle in antenna. Insert screw to secure Mount to remote.
• carefully slide the phone into Mount by pulling up on top of Mount. Adjust the angle accordingly.

OPERATING DRONE

Step 1 – Pre Flight Checklist

1. Read all warnings and instructions.
2. Install remote batteries, page 2.
3. Make sure that the drone and remote are powered off.
4. Install drone holder.
5. Charge batteries, page 3.

Step 2 – Choosing a location

• The drone is designed to be flown indoors and outdoors.
• Always make sure you have enough space to fly a drone.
• Always follow warnings, page 1.

Step 3 – Starting Drone

1. Make sure your remote is off, and slide the drone switch to ON. Drone lights will begin to flicker.
2. Place the drone on a flat even surfaces with clearance according to the diagram (Fig 1).
3. Turn the remote on. Make sure the left stick {throttle) is in a neutral position (stick is centered).
4. Push the stick up and then down.
5. A single tone indicates that the drone is paired. Drone lights will flicker rapidly and then turn on permanently once paired.
6. If pairing is unsuccessful, repeat steps 3-4.

Step 4 – Lift Oil
Prass the TAKE-OFF/LAND button on the front of the drone to lift off. The drone will elevate off the ground and level off into a hover. You can compensate for some of the drones drifting by using the Multi-Directional Button or by following Step 5.

PRACTICE INDOORS BEFORE 1 OUTDOOR FLIGHT. MAKE SURE TO RESET THE DRONE AFTER A HARD LANDING.

Step 5 – Drone Begins to Drift
Follow this step if your drone begins to drift while taking off or during flight.

• Drone drifts backward: Press the forward Direction Trim Button.
• Drone drifts forwards: Press the Backwards Direction Trim Button.
• Drone drifts left: Press the Right Direction Trim Button.
• Drone drifts right: Press the Left Direction Trim Button.
• Drone spins clockwise (viewing drone from the top): Press the Left Spin Trim Button
• The drone spins counter-clockwise (viewing the drone from the top): Press the Right Spin Trim Button

Step 6 – Operating Drone in Flight
The drones range is approximately 250 feet or 120 feet of altitude

• Read and be aware of all warnings found on Page 1.
• Maintain your desired elevation by using the Throttle.
• Push the Throttle joystick to the righ1 or left to spin the drone.
• Use the right joystick to move forward backward, and side to side.
• Review step 5 if your drone begins to drift.
• The drone will begin to blink when the drone is paired to the remote and the battery is low.

Step 7 – Landing Drone
There are two ways to land the drone:

1. Slowly and carefully press the left stick (FLIGHT AND ROTATE) down until the drone lands.
2. Or press the TAKE-OFF/LAND button to trigger auto-landing. If the drone begins to drift, you can still control the drone’s direction using the Navigation stick (right stick).

Always tum off the remote prior to retrieving or picking up the drone. This will help you avoid accidentally activating propellers.

MODES

Auto Orientation Button

• Auto Orientation default setting is off. To enter this mode press the Auto Orientation button. The Remote will beep twice.
• After the drone is successfully paired, the 2 white LED lights toward orientation will be the original forward orientation, when the drone is in auto orientation mode, the drone will orient to the user (remote), no matter what direction the drone is facing. Pushing the right stick up will send the drone away from the user, pushing It to the right will move the drone right, etc. The Remote will beep every 6 seconds to indicate the drone is in Auto Orientation mode.
• To exit mode, press the Auto Orientation button. The Remote will sound 1 long beep indicating that it has exited Auto Orientation mode.

Note : Auto Orientation mode is oriented to the user when pairing. If the remote is moved after pairing Auto Orientation, please
follow the directions above to reset Auto Orientation.

Camera – taking pictures and creating videos

• Taking a picture- press the camera icon on the app once to take a picture.
• Creating video press the video icon on the app once to take a video. Press the video icon on app again to stop recording.

TIPS

• Do not crash the drone into sand or dirt. Drone gears may become clogged
• When first learning to fly, practice lifting off and hovering
• Stay several feet from walls and buildings
• Always press throttle all the way down after crashing or when something gets stuck in the propellers
• Never fly drones above or near people, sudden changes In wind or other conditions could lead to unexpected crashes.
• Always use caution when flying drone vehicles, obey relevant laws and respect the privacy and property rights of others.
• The drone shall never be modified or used for anything except its intended purpose. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

TROUBLESHOOTING

When the remote switch is turned on, the remote light does not illuminate:

1. Check that battery in the remote are installed correctly OR
2. Replace with new batteries

During a drone flight, the remote LED is flashing:

1. Remote batteries are low; replace them with new batteries

The drone and remote properly pair, but the drone will not lift off:

1. The drone battery needs charging. Use the USB Charge Cable to connect the drone to a power source.

After Dimming the drone, the drone flight is very unstable and cannot fly properly:

1. one or more blades are most likely damaged;
2. Turn off the drone and remote.
3. Replace with the proper number of replacement blades and try flying again.

After impact, the drone is unstable:

1. Put the left remote control lever to the left bottom and put the right remote control lever to the right bottom at the same time. This will reset the gyroscope (Fig. 1).
2. If the above does not resolve the issue, reboot the drone and controller and pair again.

Remote Controller and Drone can not be paired:

1. CheckPoint: Remote Controller must be closed to Drone, not exceed 12 feet.
   Note: If there are 2 sets of Drones within 12 feet for Pairing, you must pair one successfully before pairing the second set.

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital deVice, pursuant to Pan 16 of the FCC Rules. These limits are designed IO provide reasonable protection against harmful interference in a residential installation. This equipment generates uses end con radia1e radio frequency energy and, ff not installed and used in eooordence with the instr..1C1ions, may cause harmful interference ID radio communica1ions. However, there is no guarantee1hat interference will not occur in a particular i’IS1allation. If this equipment does cause harmful Interference ID radio or television recep11on, which can be determined by turning the equipment off and on the user Is encouraged IO try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiver.
• Connect the equipment Into an outli91 on a circuit different from 1hel to which the receiver Is connected.
• Consult an Iha dealer or an experienced rack/TV technician for help.
  FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the drone at least 20cm from nearby persons. Sharper Image”‘ name and logo are registered trademarks. Distributed by and@ 2017 MerchSource, LLC. Irvine, CA 92618. All rights reserved. The artwork Bild design of this package is protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without pr1or written permission. Altering, removing, or reproducing any of the trademark or copyright notices on this package is not permitted. China Patent No. ZL2017306TT298.4 US Patent No. D846,445 Printed in Chine.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>