BRYSTON PowerPac 60 Monaural Amplifiers Owner’s Manual
- June 5, 2024
- BRYSTON
Table of Contents
BRYSTON PowerPac 60 Monaural Amplifiers
GENERAL INSTRUCTIONS
General Information:
Thank you for choosing a Bryston product. We would welcome any comments or suggestions you may have regarding the operation of your amplifier. We consider our customer to be Bryston,s most important resource and your opinion is very much appreciated. In the unlikely event you have a problem with your amplifier and must return it for service please keep the original box and all packaging material.
The Bryston PowerPac 60/120/250 are high quality modular single channel 60/120 /250 watt power amplifier intended for use in applications where portability, quality and flexibility are of prime importance.
The PowerPac is a perfect choice for use as a modular power amplifier which can be attached directly to the rear of your loudspeaker . It can also be bolted on the wall, or in the wall, for utilization in audio/video surround systems (left/right/center/rears) where a non-conspicuous power module is required. Another application would be in multi-room audio systems where single or multiple amplifiers are needed to provide music to other rooms.
Setup Recommendations:
We recommend that you do not place the amplifier in a totally enclosed area.
Allow some space at the top, sides as your Bryston amplifier relies on
convection cooling and some air flow is desirable.
Make sure the power switch on the front panel of the amplifier is in the off
(out) position. Plug the power cord into the front panel of the amplifier,
then insert the male end into the wall outlet.
All Bryston amplifiers contain high Note: Make sure that the front panel
quality, dedicated circuitry in the power sup- switch for choosing balanced or
nonplies to reject RF, line spikes and other balanced is in the correct
position. power-line problems.
Bryston power amplifiers do not require specialized power line conditioners.
Plug the amplifier directly into its own wall socket.
Connect your loudspeakers ensuring that the positive (red) and ground (black)
terminals on your amplifier are connected to the positive and ground terminals
on your loudspeakers.
Description:
The Bryston PowerPac 60 monaural amplifier consist of two of Bryston’s custom
power transistors as output devices. The power output is 60 Watts @ 8 Ohms.
The Bryston PowerPac 120 monaural amplifier consist of four of Bryston’s
custom power transistors as output devices. The power output is 120 Watts @ 8
Ohms.
The Bryston PowerPac 250 monaural amplifier consist of eight of Bryston’s
custom power transistors as output devices.
The power output is 250 Watts @ 8 Ohms.
Dimensions PP60:
(LHW) 12 X 1.8 X 7.1 Inches, 30.5 x 4.6 x 17.9 cm. Weight 5.7 Lbs/2.6Kg.
Dimensions PP120:
(LHW) 12 X 4.3 X 7 Inches, 30.5 x 10.9 x 17.8 cm. Weight 10.6 Lbs/4.8Kg.
Dimensions PP250:
(LHW) 17 X 4.5 X 8.4 Inches, 43 x 11.5 x 21 cm. Weight 23 Lbs/10.5Kg.
BRYSTON POWERPAC 60/120/250
Input and Output Connectors:
Bryston PowerPac amplifiers come
standard with two input connectors: one unbalanced RCA/phono connector and a
balanced combination XLR – 1/4-inch jack with fully discrete active input
circuitry.
All input connectors are gold-plated and should only be used only with
highquality, gold-plated interconnect cable as a poorly plated connector will
eventually corrode through the gold flash.
Bryston offers interconnect cables with heavily gold plated, quality
connectors available through any Bryston authorized dealer or directly from
Bryston.
Output connectors consist of one pair of five-way binding post terminals (1
red and 1 black) that can accept either standard banana plugs, spade lugs,
pins or bare wire. Since the binding posts are goldplated, we recommend gold
plated connectors also be used on the speaker cables.
All Bryston amplifiers will accept balanced or single-ended (RCA) input
connectors. The balanced inputs use combination 3-pin XLR (pin-1-ground),
(pin-2-+) and 1/4-inch tip-(+), ring and sleeve (ground) input connectors.
Grounding and Ground LIft Switch (except PP250):
A ground lift switch is located on the front panel of the amplifier. It is connected between the chassis ground (including the third prong on the power cord) and the signal ground.
This switch is normally left in the connected (up) position. Occasionally a multiamplifier installation or an unusual grounding situation with another component (CD player, video recorder, television etc.) will cause a ground loop between the signal ground and the chassis ground. This switch will reduce the resultant hum in many cases without resorting to a “ cheater plug ” by switching to the separated (down) position
Note: this switch does not disconnect the chassis from the third prong on the power cord which must be left intact for safety reasons.
POWERPAC 60/250 ONLY
Dual colour LED pilot lights indicating GREEN at normal level, flashing RED at clipping.
SPECIAL INSTRUCTIONS
POWERPAC 120/250
The PowerPac 120/250 remote on/off function allows the user to link the power
on/off of an amplifier, or group of amplifiers, to an external preamp, or
other control product. This is useful in installations, such
as home theater, which usually present a convenience problem for powering up
multiple amplifiers, often at distant locations from the source.
Located on the front panel of the PowerPac 120/250 (see illustration), is a two terminal 12 volts (active range 9 -12 volts AC or DC of either polarity), input connector and a potentiometer. The PowerPac amplifiers can then be poweredup by an external 12-volt signal connected to the terminals of the jack.
This jack will accept 1/4 -inch stripped wire ends, inserted into the square holes provided, and the adjacent screws carefully tightened to hold them in place. The internal “delay” turn-on circuit, will delay turn–on between 1 and 10 seconds, following application of the 12-Volts. In this way groups of amplifiers may be sequenced on to distribute power surges over a period of time.
The power switch must be left in the “off” position, at all times for the PP120 amplifier to operate in the remote mode.
The PP250 has a 3-position switch allowing for ‘Local (on)’ or ‘Off ‘or ‘REM (remote)’ power selection.
The amplifier will remain powered-up while the 12-Volt signal is present, and will turn off when the 12-Volt signal is switched off.
Input sensitivity is selectable using the
‘INPUT’ slide switch. In the BAL REG position, 2 Volts in will give
100 Watts into 8 ohms at the output. This is the recommended setting when
using Bryston preamplifiers or other pre-amplifiers having active balanced
outputs. This setting also produces the lowest noise floor.
The ‘BAL +6 dB” setting adds 6 dB of gain to provide an input sensitivity of 1 Volt in = 100 Watts / 8 ohms at the output for outputs that are transformer coupled, or low level sources.
The ‘ UNBAL’ setting selects the gold plated ‘phono’ type connector. The input impedance is 50K ohms.
BRYSTON PowerP ac SPECIFICATIONS
PowerPac 250
250 watts into 8 ohms
400 watts into 4 ohm
PowerPac 120
120W/8 ohms
200W/4 ohms
PowerPac 60
60W/8 ohms
100W/4 ohms
Gain
29dB (Unbalanced)
23dB or 29dB (Balanced)
29dB (Unbalanced)
23dB or 29dB (Balanced)
29dB (Unbalanced)
23dB (Reg.Balanced)
29dB (Pro-balanced)
Distortion
IM or THD at nominal output power < 0.007% from 20Hz to 20kHz
Noise
106dB below rated output
Power Bandwidth
<1 Hz to over 100 kHz
Input Sensitivity
Unbalanced 1.5 volts in =
250 watts into 8 ohms
Unbalanced 1 Volts in =
100 watts at 8 ohms
Unbalanced 0.75 Volts in =
60 watts at 8 Ohms
Heatsinking
Over 2,640 cm/square
Over 1550 cm/square
Over 600 cm/square
Features
Regulated power supplies to all voltage gain stages
Gold plated input and output connectors
Switchable balanced XLR – 1/4″ w/ two different gains and RCA unbalanced
inputs only for PP250 & PP120
Remote power turn-on 12V, AC/DC only for PP250 & PP120
Power Clipping Indicator only for PP120 & PP60
Soft start Power supply only for PP250
Dimensions
LxHxW = 17″x4.5″x8.4″
43×11.5×21 Cm
wt: 23 lbs
wt:10.5 kg
12″x4.3″x7″
30.5×10.9×17.8 Cm
10.6 lbs
4.8 Kg.
12″x1.8″x7.1″
30.5×4.6×17.9 Cm
5.7 lbs
2.6 Kg.
BRYSTON 20 -YEAR WARRANTY
Bryston products are warranted to be free from manufacturing defects for a minimum of twenty years from the original date of manufacture. This includes parts, labour and return shipping to the first owner and all subsequent owners. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston.
In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance.
This warranty is considered void if the defect, malfunction or failure of the product or any component part was caused by damage (not resulting from a defect or malfunction) or abuse while in the possession of the customer, tampering by persons other than factory-authorized service personnel, or failure to comply with Bryston operating instructions.
This warranty gives you specific legal rights and you may also have other rights which may vary from province to province and country to country.
BRYSTON LTD.
P.O. BOX 2170
677 NEAL DRIVE
PETERBOROUGH, ONTARIO
CANADA.
K9J 7Y4.
PHONE: 705-742-5325
FAX: 705-742-0882
www.bryston.ca
BRYSTON SERVICE IN CANADA:
24 STEINWAY BLVD., UNIT 48
ETOBICOKE, ONTARIO
M9W 6T8
PHONE: 416-675-2585
FAX: 416-675-3103
RYSTON SERVICE IN UNITED STATES:
30 COVENTRY STREET,
NEWPORT, VERMONT Suite 5.
05855
PHONE: 802-334-1201
FAX: 802-334-1201
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>