NIX E01 Hydration Biosensor POD Instruction Manual

June 5, 2024
NIX

Hydration Biosensor
NIX POD Manual

NIX E01 Hydration Biosensor POD

IC28464-E01 FCC ID: 2A6N9E01
P R O J E C T NIX
January 2022
modelE01
NIX POD Manual

Revision History

Title Date Revision By Approval Description
Initial Release 20220105 Initial Release

Control and visualization elements

NIX E01 Hydration Biosensor POD - fig

  1. RGB LED
  2. Tactile switch

Create account

The first step when opening the app for the first time is to create a user account:

NIX E01 Hydration Biosensor POD - fig1

Log in

Once the user account is created or if one already exists, you must log in.

NIX E01 Hydration Biosensor POD - fig2

Get Started

  1. Create your profile
    Some personal information must be entered in order to create personalized results:NIX E01 Hydration Biosensor POD - fig3NIX
E01 Hydration Biosensor POD - fig4
    Information that may be sensitive to some users can be omittedNIX E01
Hydration Biosensor POD - fig5

  2. Pairing
    After creating your profile, it is necessary to perform the pairing process with the pod, for this must be pressed and hold the tactile switch for 5 seconds until LED turns blue, then release the button and wait until the app completes the process.NIX E01 Hydration Biosensor POD -
Pairing

  3. Start a Workout
    To start a workout, touch the play button and follow the instructions.NIX
E01 Hydration Biosensor POD - Start a Workout
    If the pod has a patch installed, the LED shows green with a slow blinking (once per second) and jumps to workout configuration; otherwise, the LED indicates green with a fast blinking (five times per second) and shows a message asking to insert the pod in the patch.NIX E01 Hydration Biosensor
POD - Start a Workout 1
    You can choose the type of drink or continue with the processNIX E01
Hydration Biosensor POD - Start a Workout 2
    Once the workout configuration is finished, you must press the start workout buttonNIX E01 Hydration Biosensor POD - fig 4
    The workout is run (LED shows no color)NIX E01 Hydration Biosensor POD -
workout

  4. End the workout
    To end a workout, you must press the stop button located at the bottom center of the screen.NIX E01 Hydration Biosensor POD - workout
1
    A confirmation message appears before stopping the workout.NIX E01 Hydration
Biosensor POD - patch
    To end the workout the pod must be removed from the patchNIX E01 Hydration
Biosensor POD - stopping 1The data of the last workout is available

  5. NIX E01 Hydration Biosensor POD - patch4 | NIX E01 Hydration Biosensor POD - ast workout 1
    ---|---

  6. Meaning of the RGB LED

MODE AND STATE LED COLOR BLINK COMMENTS
Pairing Bluetooth BLUE 5Hz the pairing between POD and host APP
Wait to start
Ready with patch GREEN 1Hz No charger
Idle no patch GREEN Hz No patch and No charger
Charger AMBER 1Hz Charging device blink – full charge solid amber
Exercise
Active with patch NO COLOR
Interrupt RED 5Hz No patch and no charger
Interrupt + Charger AMBER 1Hz Charging device blink – full charge solid

amber
| | |
| | |
Wait to finish| | |
Have data or patch| | |
Out of charger| RED| 1Hz| No charger – pod is not connected to the charger
Have data + Charger| AMBER| 1Hz| Charging device blink – full charge solid amber

  • Blue
    Pairing between Nix Pod and App.

  • Green
    Your Nix Pod is ready for use.

  • Amber
    Blinking – charging.
    Solid – fully charged.

  • Red
    In workout – No patch detected or low battery.
    Post-workout – No Battery.

FCC CERTIFICATE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
• receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

IC-ID CERTIFICATE STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is  subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals