Altronix NetWaySP1A PoE Powered Media Converter-Repeater Installation Guide

SP1A PoE Powered Media Converter-Repeater
Installation Guide

Overview:

Altronix NetWaySP1A PoE powered media converter/repeater converts 10/100/1000 Mbps ethernet to Fiber (1000Base-X/SX/LX).

Features:

I.T.E. 43KC

Agency Listings:
• UL/cUL Listed for Information Technology
Equipment (UL 60950-1).
• CE European Conformity.
Input:
• PoE IEEE 802.3AF compliant.
• Power consumption: 2W.
Fiber Ports:
• One (1) 1Gb SFP port.
• Use with SFP module 1000Base-X (1Gb), compliant to Class 1 laser product (not included).| Ethernet:
• IEEE 802.3af (15W) compliant.
• Wire type: 4-pair CAT5e and higher.
• Connectivity: RJ45, auto-crossover.
• Speed: 10/100/1000Mbps.
• Distance: up to 100m.
LED Indicators:
• PoE Green LED: Indicates PoE present (unit is powered).
• Link Signal Green LED: Indicates SFP connection.
Environmental: Refer to Environmental Conditions on page 4.
Dimensions (W x L x H approx.): 2.5” x 3.8” x 1” (63.5mm x 96.52mm x 25.4mm).
---|---

Installation Instructions:

Unit is powered via CAT5e by midspan or endspan. NetWaySP1A is not intended to be connected to outside plant leads and should be installed indoors within the protected premises.

1. Mount NetWaySP1A in the desired location utilizing the mounting hole (Fig. 1a, pg. 2). Use a proper fastener and/or wall anchor when securing NetWaySP1A with a screw through its mounting hole to the wall.
   Note: Earth ground can be used, if needed, for high transient or outdoor environments. If used, insert an Earth ground wire (included with product) into the internal ground terminal until secured (a slight tug can check stability) & fasten the free end to a chassis earth ground.
   If earth ground is not attached and needed, refer to Fig.1b, pg.2 for manual placement.

2. Connect the structured cable from the port marked [PoE 10/100/1000 In] on NetWaySP1A to the corresponding input of a UL Listed Ethernet switch or a midspan. PoE LED will illuminate indicating normal operation (Fig. 1, pg. 2).

3. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP] on the NetWaySP1A. Connect the other end of the fiber cable to an SFP module of a remote device. SFP LED will illuminate indicating data connection (Fig. 1, pg. 2).

Interconnecting Multiple Fiber/Ethernet Devices:

NetWaySP1A can be used for daisy-chaining two (2) Fiber/Ethernet devices such as Altronix NetWaySP3 Series or NetWay4EX Series hardened switches.
Refer to NetWaySP3WPN / NetWay4EWPN Installation Instructions.

1. Connect one end of a CAT5 cable to one of the Ethernet ports of the hardened PoE switch e.g., NetWaySP3WPN or NetWay4EWPN (Fig. 3, pg. 3).
2. Connect the other end of the structured cable to the port marked [PoE 10/100/1000 In] on NetWaySP1A (Fig. 3, pg. 3, Fig. 1b pg. 2).
3. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP] on the NetWaySP1A. Connect the other end of the fiber cable to an SFP module and connect that module to the Fiber input of the next NetWaySP3WPN or NetWay4EWPN (Fig. 3, pg. 3, Fig. 1 pg. 2).

Typical Applications:

Interconnecting Two Switches:
Fig-3

Technical Specifications:

Link Signal Green LED: Indicates SFP connection.
Environmental Conditions| Operating: -40°C to 75°C (-40°F to 167°F).
Storage: -40°C to 75°C (-40°F to 167°F).
Relative Humidity 85% +/-5%.
Operating Altitude: -304.8 to 2,000m.
Regulatory Compliance| UL/cUL Listed for Information Technology Equipment (UL 60950-1)
I.T.E.43KC
CE European Conformity.
Weights (approx.)| Product weight: 0.15 lb. (0.07 kg) I Shipping weight: 0.5 lb. (0.22 kg).

Recommended Altronix SFP Modules:
Altronix P1MM, P1SM10, P1AB2K, and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM – For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 – For use with Single-Mode Fiber for distances up to 10km.
P1AB2K – For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE – For use with CAT5e or better for distances up to 100m.

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA
phone: 718-567-8181
fax: 718-567-9056
website: www.altronix.com
e-mail: info@altronix.com
Lifetime Warranty
NetWaySP1A Rev. 021517
F17U

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>