Funai Electric R D U9W43 WiFi Module User Manual
- June 5, 2024
- Funai Electric R D
Table of Contents
Funai Electric
R D U9W43 WiFi Module
User Manual
Electric R D U9W43 WiFi Module
Since this module is not sold to general end-users directly, there is no user
manual of the module.
For the details about this module, please refer to the specification sheet for
the module.
This module should be installed in the host device according to the interface
specification (installation procedure).
FCC Statements
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The modular can be installed or integrated into mobile or fixed devices only.
This modular cannot be installed in any portable device, for example, USB
dongle-like transmitters are forbidden. This modular complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This modular must be installed and operated with a
minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: 2AU3BU9W43 Or Contains FCC ID: 2AU3BU9W43”
When the module is installed inside another device, the user manual of this
device must contain the below warning statements:
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.
The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The end-user manual shall include all required regulatory information/warning as shown in this manual, including: This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
ISED Statements
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
The modular can be installed or integrated into mobile or fixed devices only.
This modular cannot be installed in any portable device, for example, USB
dongle-like transmitters are forbidden.
This modular complies with IC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This modular must be
installed and operated with a minimum distance of 20 cm between the radiator
and user body. Cette modulaire doit être installé et utilisé à une distance
minimum de 20 cm entre le radiateur et le corps de l’utilisateur.
If the IC number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label can
use wording such as the following: “Contains IC:25625-U9W43”
when the module is installed inside another device, the user manual of this
device must contain the below warning statements;
- This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product
The following information must be indicated on the host device of this module;
[for FCC]
Contains FCC ID: 2AU3BU9W43
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe it in the user’s manual and also either describe it on the device packaging or on a removable label attached to the device.
[for ISED(IC)]
Contains IC: 25625-U9W43
The following statements must be described on the user manual of the host
device of this module;
[for FCC]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. NOTE: THE
MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. To comply with FCC RF exposure compliance requirements, this grant
is applicable to only Mobile Configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
[for ISED(IC)]
This device contains license-exempt transmitters/receivers that comply with
Innovation, Science, and Economic Development Canada’s license-exempt RSS
standards. Operation is subject to the following two conditions: (1) This
device may not cause interference (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
for indoor use only (5150-5250MHz)
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)
Exposure rules. To comply with FCC RF exposure compliance requirements, this
grant is applicable to only Mobile Configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
[for FCC]
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other
words, this device automatically discontinues transmission in case of either
absence of information to transmit or operational failure.
[for ISED(IC)]
Data transmission is always initiated by software, which is passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other
words, this device automatically discontinues transmission in case of either
absence of information to transmit or operational failure.
[§15.105 Information to the user]
For a Class B digital device or peripheral, the instructions furnished by the
user shall include the following or similar statement, placed in a prominent
location in the text of the manual.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Complies with the Canadian ICES-003 Class B specifications.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>