ADJ MDF2PSUX117 External Power Supply User Manual
- June 5, 2024
- ADJ
Table of Contents
MDF2PSUX117
Safety Manual
©2022 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands, and product names are trademarks or registered trademarks of their respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update
of this manual before beginning installation and/or programming.
Date| Document Version| Software Version| DMX
Channels| Notes
---|---|---|---|---
12/17/2021| 1.0| N/A| Not Applicable| Initial Release.
01/28/2022| 1.1| N/A| Not Applicable| Updated Specifications.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help to protect the enviroment. Please turn
off all electrical products when they are not in use. To avoid power
consumption in idle mode, disconnect all electrical equipment from power when
not in use. Thank you!
INTRODUCTION
Unpacking: Thank you for purchasing the MDF2PSUX117 power supply for the MDF2 dance floor system by ADJ Products, LLC. Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the event that damage has been found or parts are missing, please contact our toll-free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The ADJ MDF2PSUX117 is a power supply unit intended for use with the ADJ MDF2 dance floor panels. To optimize the performance of this product, please read these instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit for future reference.
Customer Support: Contact ADJ Service for any product-related service and support needs. Also visit forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit: http://parts.adj.com(US) http://www.adjparts.eu (EU)
ADJ SERVICE USA – Monday – Friday 8:00am to 4:30pm PST Voice:800-322-6337 I Fax: 323-582-2941 support@adj.com
ADJ SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET Voice: +31 45 546 85 60 I Fax: +31 45 546 85 96 support@adj.eu
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 I Fax
323-532-2941
www.adj.com infoitadj.com
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands +31 (0)45 546 85 00 I Fax
+31 45 546 85 99 www.americandj.eu
info@americandj.eu
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000 +52
728-282-7070
CAUTION! There are no user-serviceable parts inside this unit. Do not attempt any repairs yourself, as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service, please contact ADJ Products, LLC.
Do not discard the shipping carton in the trash. Please recycle whenever possible.
LIMITED WARRANTY (USA ONLY)
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products,
LLC products to be free of manufacturing defects in material and workmanship
for a prescribed period from the date of purchase (see specific warranty
period on reverse). This warranty shall be valid only if the product is
purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place
of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#)
before sending the product back—please contact ADJ Products, LLC Service
Department at 800-322-6337. Send the
product only to the ADJ Products, LLC factory. All shipping charges must be
prepaid. If the requested repairs or services (including parts replacement)
are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package and
packaging material. No accessories should be shipped with the product. If any
accessories are shipped with the product, ADJ
Products, LLC shall incur no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are
altered or removed; if the product is modified in any manner which ADJ
Products, LLC concludes, after inspection, affects the reliability of the
product; if the product has been repaired or serviced by anyone other than the
ADJ Products, LLC factory unless prior written authorization was issued to
purchaser by ADJ Products, LLC; if the product is dammed aged because it was
not properly maintained as set forth in the product instructions, guidelines
and/or user manual.
D. This is not a service contract, and this warranty does not include
maintenance, cleaning, or periodic checkup. During the period specified above,
ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship. The sole responsibility
of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or replacement thereof, including parts, at the sole discretion of
ADJ Products, LLC. All products covered by this warranty were manufactured
after August 15, 2012, and bear identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or
improvements to its products without any obligation to include these changes
in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to
any accessory supplied with products described above. Except to the extent
prohibited by applicable law, all implied warranties made by ADJ Products, LLC
in connection with this product, including warranties of merchantability or
fitness, are limited in duration to the warranty period set forth above. And
all warranties, whether expressed or implied, including warranties of
merchantability or fitness, are limited in duration to the warranty period set
forth above. The consumer’s and/or dealer’s sole remedy shall be such repair
or replacement as is expressly provided above; and under no circumstances
shall ADJ
Product, LLC is liable for any loss and/or damage, direct and/or consequential
arising out of the use of, and/or inability to use this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC
products, and supersedes all prior warranties and written descriptions of
warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
- Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED and lamps)
- Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
- LED Products = 2-Year (730 Days) (excluding batteries that have a 180 Day Limited Warranty)
- NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to products purchased within the United States. StarTec Series = 1-Year (365 Days) (excluding batteries that have a 180 Day Limited Warranty)
- ADJ DMX Controllers = 2 Year (730 Days)
- American Audio Products = 1 Year (365 Days)
FEATURES
INCLUDED ITEMS
Power Cable (x1)
IP RATING
This device is IP20 rated. This means that the unit is protected against
intrusion from solids approximately the size of an adult finger (12mm in
diameter), and that the unit is NOT protected against water intrusion of any
kind!
SAFETY GUIDELINES
THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO GUARANTEE SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS AND GUIDELINES IN THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR INJURY AND/OR DAMAGES RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE DISREGARD OF THE INFORMA770N PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR CERTIFIED PERSONNEL SHOULD PERFORM THE INSTALLATION OF THIS FIXTURE AND ONLY THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS FIXTURE SHOULD BE USED FOR INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR THE INCLUDED MOUNTING HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY AND INCREASE THE RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL SHOULD PERFORM THE INSTALLATION OF THIS FIXTURE.
-
PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
-
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT.
-
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
-
DO NOT USE OUTDOORS OR BE EXPOSED TO MOISTURE OR HUMIDITY!
-
DO NOT PLUG THE UNIT INTO A DIMMER PACK!
-
NEVER OPEN THIS UNIT WHILE IN USE!
-
UNPLUG POWER BEFORE SERVICING THE UNIT!
-
NEVER TOUCH THE UNIT DURING OPERATION, AS IT MAY BE HOT!
-
KEEP FLAMMABLE MATERIALS AWAY FROM THE UNIT!
-
THE MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)
-
THE OPERATING AMBIENT TEMPERATURE RANGE IS -4° F TO 158° F (-20°C TO 70°C). DO NOT
OPERATE THE DEVICE WHEN AMBIENT TEMPERATURE FALLS OUTSIDE THIS RANGE. -
THE MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METERS).
-
DO NOT TOUCH the unit housing during operation. Turn OFF the power and allow approximately 60 minutes for the unit to cool down before serving.
-
DO NOT shake the unit, and avoid brute force when installing and/or operating the unit.
-
DO NOT operate the unit if the power cord is frayed, crimped, damaged, and/or if any of the power cord connectors are damaged and do not insert into the unit securely with ease. NEVER force a power cord connector into the unit. If the power cord or any of its connectors are damaged, replace it immediately with a new one of the same power rating.
-
DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow 6″ (15cm) between the unit and other devices or a wall for proper cooling.
-
Always disconnect the unit from the main power source before performing any type of service and/or cleaning
-
Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of the cord.
-
Consistent operational breaks will ensure fixtures will function properly for many years.
-
ONLY Use original packaging and materials to transport the fixture in for service.
OVERVIEW
INSTALLATION
FLAMMABLE MATERIAL WARNING
Keep fixtures a minimum of 5.0 feet (1.5m) away from flammable materials
and/or pyrotechnics.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or
installations.
THE MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS).
THE MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE IS 1.6
FEET (0.5 METERS)
DO NOT EXPOSE TO RAIN OR MOISTURE!
INDOOR USE ONLY!
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
- Fixtures MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
- The ambient temperature operating range is -4° F to 158° F (-20°C to 70°C). Do not use operate the unit when the ambient temperature falls outside of this range!
- Device(s) should be installed in areas outside walking paths, seating areas, or areas where unauthorized personnel might reach the fixture by hand.
- Allow approximately 60 minutes for the fixture to cool down before servicing.
IP RATING
This device is IP20 rated. This means that the unit is protected against
intrusion from solids approximately the size of an adult finger (12mm in
diameter), and that the unit is NOT protected against water intrusion of any
kind!
INSTALLATION
CONNECTIONS
Each of the nine (9) Power Out connections should be linked via a power cable
to a single Power Ramp from the MDF2 system. When used in conjunction with the
MDF2PSUX117 power supply, each Power Ramp is able to support a single row of
up to twelve (13) dance floor tiles, for a total of 117 dance floor tiles.
When installing the dance floor panels in place, pay close attention to the
directional orientation arrows located on the side faces of each panel. When
placed correctly, these arrows should indicate the direction of power flow
from the Power Ramp to the first panel, then to each subsequent panel down the
line. These panels must be positioned in a straight line to receive and
transmit power. If the panel is rotated 90 degrees, or if the panel is placed
with the directional arrow pointing back towards the power source, the panel
will not receive power or be able to transmit power to any subsequent panels
down the line.
Please see the illustration below, or refer to the user manual for the ADJ
MDF2-9SYS for detailed information.
NOTE: Directional orientation arrows are depicted on the top surface of the panels for the sake of clarity. Actual panels will have directional orientation arrows located on the sides of the panels.
TROUBLESHOOTING
Below are some common issues that you may encounter during use, along with possible solutions. If the steps below do not solve your problems, please contact the ADJ support line at the phone number or e-mail address listed in the Introduction section of this manual.
No voltage output from power supply:
- Check that there is voltage output from the power socket.
- Check whether the fuse has been tripped. If so, replace the fuse. It is also strongly advised to check the layout of the dance floor panels to make sure that have been oriented correctly, in order to avoid tripping the fuse again.
- Check that the cable connecting the power supply to the dance floor assembly is securely connected.
Fuse or circuit breaker trips repeatedly:
- Check whether the power demand exceeds the maximum load output of the power supply. If so, reduce the number of dance floor panels connected to this power supply.
- Check whether the fuse itself is faulty. Replace the fuse with a new fuse of the correct type.
- Check the condition of the dance floor panels themselves to ensure that they are not working in an abnormal manner.
DIMENSIONAL DRAWINGS
SPECIFICATIONS
ELECTRICAL
Input Voltage: AC 100-240V, 50/60 Hz
Output Voltage: DC 24V
Maximum Load Power: 2250 W
Load Current: 90 A
Current Overload Protector Trip Time:
- Within 10A of max load: no trip
- 10-15A over max load: trip within 1 hour
- 15-20A over max load: trips in 5.2 to 30 seconds
- 20-30A over max load: trips in 1.5 to 5.5 seconds
DIMENSIONS
Length x Width x Height: 19.7” x 17.0” x 8.1” (500.0mm x 433.0mm x 205.5mm)
Weight: 30.0 lbs (13.6 kg)
AMBIENT OPERATING CONDITIONS
Ambient Operating Temperature: -4°F to 158°F (-20°C to 70°C)
IP Rating: IP20
References
- Topics | ADJ Forums
- ADJ Product Parts - Lighting Online Parts Store
- Home
- ADJ Partsshop - Service is our passion!
- ADJ Supply Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>