Getac ZX10 NFC 10 Inch Fully-Rugged Android Tablet User Guide
- June 5, 2024
- Getac
Table of Contents
Getac ZX10 NFC 10 Inch Fully-Rugged Android Tablet
USER GUIDE
- Select and click the “Getac Settings” APP
- Select and click the “NFC reader” in “Getac Setting”
- Put the NFC tag on the NFC reader area of system backside surface.
- NFC tag information show on the front side screen of “NFC Reader” .
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE
This NFC device must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product. Any other installation or use will violate FCC Part 15
regulations. Modifications not expressly approved by Getac could void your
authority to operate the equipment. This module apply limit module approval,
and just only installs in the end product (Brand: Getac / Model: ZX10).
Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: QYLPN7150Z11”. The grantee‘s FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information to the End User:
The OEM integrator has to be aware not to provide information to the end-user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end-user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada Statement
Canada, Industry Canada (IC) Notices
Class B digital circuitry of this device complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, the radio transmitter(s) in this device may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This module apply limit module approval, and just only install in end product (Brand: Getac / Model: ZX10).
End Product Labeling:
The product can be kept as far as possible from the user body or set the
device to lower output power if such a function is available.
The final end product must be labeled in a visible area with the following:
“Contains IC: 10301A-PN7150Z11”
Manual Information to the End User:
The OEM integrator has to be aware not to provide information to the end-user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as shown in this manual.
Radio Frequency (RF) Exposure Information
The radiated output power of this device is below the Industry Canada (IC)
radio frequency exposure limits. This device has been evaluated for and shown
compliant with the IC Radio Frequency (RF) Exposure limits. The device should
be used in such a manner such that the potential for human contact during
normal operation is minimized.
This device has been certified for use in Canada. Status of the listing in the
Industry Canada’s REL (Radio Equipment List) can be found at the following web
address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be found at the
following web address: http://www.ic.gc.ca/eic/site/smt-
gst.nsf/eng/sf08792.html
Antenna Information
Antenna
|
Antenna Net Gain (dBi)
|
Frequency Range
|
Antenna Type
|
Connector Type
---|---|---|---|---
NFC antenna
|
0
|
13.56MHz
|
Loop Antenna
|
NA
Label Sample
PN7150
- FCC ID: QYLPN7150Z11
- IC: 10301A-PN7150Z11
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>