Heiden HD019 Monaco Single Watch Winder Dual Powered Instruction Manual

Heiden HD019 Monaco Single Watch Winder Dual Powered

AC OPERATION

Plug in the AC power adapter to the wall and insert the DC power plug into the power jack on the back of the unit.
Note: Disconnect the AC power adapter when the winder is not in use.

DC OPERATION

Insert D-sized batteries into the battery compartment at the back of the unit.
Note: Batteries are not included. Remove all batteries when the winder is not in use.

LOADING THE WATCH ON THE WATCH PILLOW

Take out the watch pillow and squeeze it to a suitable size, then fasten the watch on it.

PLACING YOUR WATCH TO THE WINDER

Insert watch and watch pillow into the watch winder holder.

MODES OF WINDING

Slide the switches to select the winding modes.
There are 4 turning modes {TPD – turns per day) and 3 direction modes (clockwise, counterclockwise and both directions) to wind your watch.

TURN ON THE POWER

Press the round power button to turn on the watch winder and start the turning.

UPRIGHT POSITIONING

The watch will return to the starting upright position at any resting time and before power off.
Note: 1 to 2 degrees angle deviation in upright positioning is normal. upright positioning does not function when AC power is disconnected.

MODES SPECIFICATIONS

TPD

(Approximately}

650

| ****

Cycles Per Day

24

| Counterclockwise winding (Approximately minutes)

3:11 min

| Clockwise winding (Approximately minutes)

3:11 min

| Bidirectional winding (Approximately minutes)

1:35 min

| Resting Time (Approximately minutes)

56:49 min

---|---|---|---|---|---
950| 24| 4:40 min| 4:40 min| 2:20 min| 55:20 min
1250| 24| 6:08 min| 6:08 min| 3:04 min| 53:52 min
1850| 24| 9:04 min| 9:04 min| 4:32 min| 50:56 min

Data is based on using an AC adapter. Values may vary depending on the weight of different watches. Please note that the watch winder is programmed to turn, rest and turn again for each setting. The watch winder will not turn constantly to prevent over-winding of your watch. This is the normal operation for the watch winder.

MAINTENANCE

Do not expose the watch winder to direct sunlight, extreme temperatures, water, or other moisture which may damage the winder. Clean the winder surfaces with the microfiber pouch that comes with the package. Do not use solvent-based cleaning agents. Please do not open the watch winder or attempt to repair it.

Tips for your new watch winder!

All automatic watches have different TPD requirements but on average most automatic watches need a minimum of 650-1200 TPD. All of our watch winders are set to accommodate this minimum requirement. To find the right setting for your watch we recommend the following procedure:

1.  Manually wind the watch by turning the crown 20-30 times. The watch winder will not wind a completely dead watch.
2.  Set the winder to the lowest TPD setting and bi-directional rotation. Place the watch in the winder and make sure it is seated properly and securely in the holder.
3.  Turn the winder on and periodically check to make sure the time is correct. Most automatics have a maximum of 40 hours of power reserve when fully wound so if the time is correct after 2 full days, this is the proper setting for your watch.
4.  If the time is incorrect, please set it to the next highest TPD setting and try again.
5.  If the time is incorrect, please set it to clockwise only and try again.
6.  If the time is incorrect, please set it to counter-clockwise only and try again.
7.  If the watch works while it is being worn but does not work in the winder, it may need to be serviced. When a watch is worn, the movements it experiences are not as smooth as in a watch winder, so while a watch may work when its worn it may not work when in the winder. Watch winders move very smoothly so if the lubrication inside the watch has congealed from not being in use, the watch may need to be serviced.
8.  If you still have problems or issues please feel free to contact us.

Below is a list of popular watch brands and common settings for most of their watches. Specific models from some brands may have exceptions and may not work on the setting listed below. If this is the case please contact us and we will try to determine the correct setting for your particular model.

Share Your Honest Review To Help Others Make a Purchase Decision

• Step 1 – Find the product you purchased on Amazon.com
• Step 2 – Click on customer reviews
• Step 3 – Click on “Write a customer review”

OR

• Step 1 – Visit Amazon.com and login to your account
• Step 2 – Go to “Orders”
• Step 3 – Find the item and click on “View Details” and click on “Write a product review”
  If you purchased from another website, please visit the website and post your product review on their website.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>