FnFly E5 High Quality Stereo Bluetooth Headset User Manual
- June 5, 2024
- FnFly
Table of Contents
The user manual
High quality stereo Bluetooth headset
For proper and safe use of this headset, please read this manual carefully
before use.
The following matters should be noted when using earphones:
- Please reasonably control the time and volume of using the earphone.
- To ensure safety, please do not use the earphone in a potentially dangerous environment (such as a thunderstorm).
- Try not to use headphones to listen to music, make or receive phone calls and distract your attention while driving It creates danger.
- Please keep the earphones out of reach of children to avoid fatal danger caused by improper use of children.
- Avoid water in the earphone, so as not to damage the earphone function.
- Avoid constantly turning up the volume, which will cause you to not hear the surrounding sounds, such as tinnitus or too high volume adjustment “, please turn the volume down.
- If you feel obvious discomfort, irritation, or other adverse reactions when using the earphone, stop using them immediately.
Specifications:
Working Range: 10 m | Frequency Response: 20Hz-20KHz |
---|---|
Input Voltage: 5V-1A | Impedance:32Ω Speaker:Φ10mm |
Battary:3.7V/110mAh | Support: A2DP/AVRCP/HSP/H FP |
Charge Temperature: 0 -45°C | Working Temperature: -20-50°C |
BT Version : 5.2 | Net Weight: 33g |
Warning :
- Do not wear it while charging, in case of electric shock.
- This earphone uses a built-in non-removable rechargeable battery. Do not remove the battery from the headset to avoid damage to The headset.
Headphone Charging:
- The headset will be forced to automatically shut down during charging, and the charging interval cannot be started up;
- Plug the USB charging cable into the headset charging port, and plug the USB port on the other end into the USB charger or the USB port of the computer. The red LED is always on when charging;
- Charging time is about 2.5 hours, the blue light is always on after full charge.
Function Button
Package list Headset products 1PC
USB charging line 1PC
GS2 User Manual 1PC
The silicone ear cap 2PC
NO & OFF:
- In the OFF state, press MF button for 1 seconds (Blue LED flash while “POWER ON” voice prompts).
- In the ON state, press the MF key for 5 seconds, and the red light is steady. At the same time, the ‘POWER OFF’ prompt tone is heard.
BT pairing steps:
- Connect BT headphones to your mobile (or other device used connection) in the range of the meter.
- In the OFF state, press MF button for 5 seconds, note: “POWER ON” and “Pairing” then open the Bluetooth function of your mobile
- Search and choose “ENFLY2021-9” to connect.
PS Note:
- If the headset has already been connected, press 1 second to turn it on again, it will automatically connect to the last connection Devices, moreover if headphones on the boot around after connection of equipment after 10 seconds into pairing mode automatically, the convenient user (not connected devices) with new equipment matching, headphones, of course, also support long press 5 seconds after the boot directly into pairing mode, boot directly into pairing mode after repeat the above steps Bluetooth connection can be matched.
- The time to enter the pairing mode is only 5 minutes. After the timeout, the headset will shut down automatically. Please restart the headset if you use it again.
Disconnected and reconnecting:
- Bluetooth will disconnect when the distance is beyond the Bluetooth receiving range. Red and blue LED lights will flash alternately,and a “disconnected” prompt voice will appear, then a “pairing” prompt voice will appear. After disconnecting for more than 5 minutes, the headphone will automatically shut down, and within 3 minutes the headphone can automatically connect back to the phone, and a “connected” prompt voice appears.
- If you operate the phone directly and turn off the Bluetooth of the phone, the Bluetooth headset will automatically enter the pairing mode.
Phone Call Pick-up:
Short press the MF button once when the call comes.
Phone Call Hang-up:
Short press the MF button once during the call period.
Phone Call Reject
Double-click the MF button when the call comes in.
Call Waiting:
When there is a second call, double-click the ‘MF button’ once to keep the
first call and answer the second call. Double-click the “MF Button” again to
reserve the second call and answer the first call. Click the “MF button’ to
suspend the current call and connect to the second party.
Music Mode/Game Mode:
1. Double-click the ‘MF button’ in the connection state, and the sound will
prompt you to switch Game Mode /Music Mode
LED atmosphere light:
1. In the connection state, triple press the “MF button’, Long Light – Quick
Flash – Slow Flash – Breathing Light – Off operation, and LED atmosphere light
switch.
Playing/Pause:
Short press the ”MF button” When Playing music.
Music Selections:
When playing music, short press the volume plus button to jump to the next
song, short press the volume minus button to jump to the previous song.
Volume Control:
When listening to music or talking, long-press the volume button to reduce the
volume gradually, the same long-press the volume button to increase the volume
gradually, and the maximum volume appears ‘drop’ a prompt tone.
Reset:
Under shutdown state, long press MF key 10S to clear pairing list, restore
factory Settings, clear pairing information, and then automatically enter
pairing mode
Change the prompt language
The earphone is equipped with Chinese and English prompt tones. When the phone
is disconnected from the headset, press the MF button five times to switch the
Chinese and English prompt tone.
Low voltage alarm:
When the power of the headset is lower than 3.3V, the red LED will flash
quickly, and the “low power” prompt sound will appear repeatedly to continue
to use. When the power is too low, it will automatically shut down.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>