Shenzhen Huazhitai Technology HZT-1003J 12V LED Deck Light Instruction Manual
- June 5, 2024
- Shenzhen Huazhitai Technology
Table of Contents
Shenzhen Huazhitai Technology HZT-1003J 12V LED Deck Light
instruction manual
Read the instruction carefully before use!
- Make sure LEDs are not installed within the reach of children.
- Check all connections before connecting the main adapter to a power outlet.
- Disconnect the main adapter from the power outlet if the LED are not working properly
- Super quality LED chips(0.8W/pcs), DC12V low voltage output, no flicker, durable and stable copper2 pin connector(DC 12V Transformer Included, Support Max16pcs in Series)
- The LED dot lights are detachable and in parallel connection. you can only install part of them based on your needed(The led deck light kits still works fine if one or two of the deck lights fails.)
Installation
- Drill hole, insert light, connect the wire to the transformer, repeat again for each light connecting the wire to last light
- The pointing arrowhead must aim at the slot.
LED Deck Light
Read these instructions carefully before use!
- Make sure LEDs are not installed within the reach of children.
- Check all connections before connecting the main adapter to a power outlet.
- Disconnect the main adapter from the power outlet if the LED is not working properly.
Installation
Drill hole, insert light, connect the wire to the transformer, repeat again
for each light connecting wire to last light.
Application
- Deck steps, deck edge, stairs steps, outdoor walkways, landscape lighting.
Remote Control Function Description
ON/OFF: On/Off Button
- TIMER RESET: Release the function of the timing button/code matching button; O. In the timing state, press and flash twice, release the timing function. In the non-timing state the operation is invalid;
- Code Pairing Function: Code pairing can be performed within 1 minute after power-on; power-off and restart is required for code pairing after timeout code pairing operation: long press for 2seconds, flash 5 times and then enter the current working mode;
- 4H timer button (press it flash once and it will start to count down for 4 hours) with a memory function, it will work for 4 hours after shutting down and restarting;
- 8H timer button (press it flash once and it will start counting down for 8 hours) with a memory function and it will work for 8 hours after shutting down and restarting;
- 12H timer button (press it flash once and it will start counting down for 12 hours) with a memory function, and it will work for 12 hours after shutting down and restarting.
- Brightness decreasing, ABrightness increasing: 5 levels of brightness adjustment: 6 100%–75%–50%–25%–10%.
- MODE: Mode Button:
- The initial state is always on.
- Breathing Light Mode: 100%-10%/10%-100% brightness cyclically and gradually, the cycle time is 20 seconds; in the breathing light state, you can choose the color button and the timing button, if you press other buttons, it will be released breathing mode.
- Three-Color Gradient Mode: white light-warm white light-warm light-automatic color switching. The cycle time is 20 seconds; the timing button can be selected, if you press other buttons, the color gradient will be released.
- Small Sun- -Medium Sun- -Big Sun Brightness adjustment, 10%–50%–100% brightness fast switching function
- White light–Warm White light–Warm light: Mode switch button
- Memory Function: Live memory function, after the current working state is turned off or scheduled to be turned off, the next time turned on, it will continue to work in the current working mode;
- Power-Off Memory Function: Each time the power is plugged in, the brightness is the brightness before the shutdown;
- Instructions for shifting gears if the remote control is broken: If the remote control is broken, you can switch colors through quick power-on and power-off operations.
Output Power: 12V
- The maximum output power of white light: 12W (lamp power)
- The maximum output power of warm white light: 12W(lamp power)
- The maximum output power of warm light: 12W (lamp power)
Note: Support up to 20 lamp connections.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>