JBC SF-110VB SF Series Auto Solder Wire Feeder Instruction Manual
- June 5, 2024
- JBC
Table of Contents
JBC SF-110VB SF Series Auto Solder Wire Feeder Instruction Manual
This manual corresponds to the following references:
SF-110VB (110-120V) with Guide Set ø1mm
SF-210VB (230V) with Guide Set ø1mm
Packing List
The following items are included:
Features and Connections
Tool Assembly
Connect the tool to the control unit following this steps:
Insert and push the guide nozzle until the end (1) and tighten the screw (2).
Connect the jack (3).
Solder-Wire Loading
Put the solder reel into its support (1).
Introduce the solder wire into the inlet nozzle (2) until it reaches the wheels (3).
Use the Tin Reload Process in the Main Menu (4).
The Reload Process screen opens.
Press to start the process.
Make sure the wire passes through the Intermediate Nozzle and enters into the Guide Tube (5).
Changing Guide Kits
Changing Wheels and Blade
For this operation, disconnect the device from the mains. Disconnect the tool from the control unit and open its cover.
First disassemble the guide tube (6), the nozzles (2)+(3), then the wheels, blade and clamp (4)+(5). Disassemble the counter wheel (1). Use the allen key and the spanner, provided with the station.
Assembly with Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the guide wheel (4) and tighten the screw.
Assemble the blade first, then mount the blade clamp (5) onto the same axis and tighten the screw. Caution: handle the blade carefully to avoid injury.
Insert the guide set (6).
Assembly without Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the traction wheel (4) onto the axis and tighten the screw.
Assemble the support wheel (5) and tighten the screw.
Insert the guide set (6).
Replacing the Guide Tube
Once the tool is disconnected from the control unit follow the instructions below:
Disassemble the outlet nozzle (1) from the guide tube.
Open the guide clamp (2), take off the guide tube (3) and insert the new one.
Note: The guide tube length can be easily adjusted (4) when the guide
clamp knob (2) is open.
Once the guide tube length is adjusted close the guide clamp knob (2).
Assemble the outlet nozzle (1) onto the guide tube tip.
Enter en “Tool Settings” at the SF control unit main menu and select the proper wire diameter.
SF with Guide Tube assembled
SF without Guide Tube assembled
Control Process
Work Screen
Choose between continuous, discontinuous and program mode:
Program Mode
With the SF you can define up to 35 dynamic programs. In each one you can configure up to 3 steps with different lenght wire and dispensing speed.
Execute them sequentially and cyclically with the ‘Edit Concatenation List’ option.
Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com
Menu Screen
Default PIN: 0105
*choose between total and partial counters
Accessories*
Guide Kits
Various guide kits are available to choose from depending on the diameter of the welding wire used.
Tool Stand
Stand for SF280 Auto Solder-Wire Handle
Ref. SF-SE
It prevents SF280 from rolling away while working.
GSF Guide Kit for SF280 with Solder-Wire Perforation
GSF Guide Kit for SF280 without Solder-Wire Perforation
Maintenance
Before carrying out maintenance, always allow the equipment to cool down.
-
Clean the station screen with a glass cleaner or a damp cloth.
-
Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
-
Periodically check all cables and tubes.
-
Replace a blown fuse as follows:
-
Pull off the fuse holder out and remove the worn fuse. If necessary use a tool to lever it off.
-
Insert the new fuse into the fuse holder and assemble it to the station.
- Replace any defective or damaged parts. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
SF
Auto Solder-Wire Feeder
Ref.: SF-110VB 100-120V 50/60Hz. Input fuse: T0.2A.
Ref.: SF-210VB 230V 50/60Hz. Input fuse: T0.125A.
-
Compatible Solder Reel:
Weight up to 1 kg / 2.2 Ib
Diameter Max. 80 mm / 3.15 in
Height Max. 75mm / 2.95 in -
Solder Wire Diameter
ø0.9 – ø 1.0 mm / ø0.035 – ø0.040 in -
Max. Wire Length
250 mm / 9.84 in -
Max. Forward Speed
120 mm/s / 4.72 in/s -
Max. Reverse Speed
120 mm/s / 4.72 in/s -
Ambient Operating Temp:
10 – 50 ºC / 50 – 122 ºF -
USB Connector Station-PC
-
Robot Connector
-
Dimensions / Net Weight:
(L x W x H)
140 x 150 x 120 mm / 2.32 kg
5.5 x 5.9 x 4.72 in / 5.11 lb -
Total package Dimensions / Weight:
(L X W X H)
368 x 368 x 195 mm / 3.23 kg
14.5 x 14.5 x 7.68 in / 7.12 lb
Complies with CE standards.
ESD safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse. In order for the warranty to
be valid, equipment must be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warranty by registering
here:https://www.jbctools.com/productregistration/ within 30 days of
purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility.
0028008-310522
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>