IFAMILY SM651 Digital Wireless Video Baby Monitor with 5.0 Inches Color Screen User Manual

IFAACMILY SM651 Digital Wireless Video Baby Monitor with 5.0 Inches Color

Screen

Safety Instruction

CAUTION
Keep small parts away from children.

Strangulation Hazard
Children can become entangled in cords. Power cords should be kept more than 3 feet away from the crib and baby’s reach all the time. Baby monitors and cameras with power cords should never be hung on or near the crib. This product is not a toy and should be kept out of children’s reach. This product contains small parts. Be care when unpacking and assembling the product. This product cannot replace responsible adult supervision.

Water  and moisture
This  product  is designed  for  indoor  use  only. The unit should not be exposed to rain, moisture, dripping  or splashing. No objects filled with liquid should be placed on top of, or beside the product, such as a glass or vase. This item should not be used near water.

DO NOT USE THE APPLIANCE

• If the cord or plug is dam
• If your baby monitor is not operating properly or has suffered any damage.

Contact service
The service center to request inspection and repair it in order to avoid any possible risk. Do not attempt to repair or adjust any of the electrical or mechanical functions of the unit since, if you do, the guarantee will be made void.

Ventilation
This baby monitor should not be used on a bed, sofa, rug or similar surface that may block the ventilation openings, or be placed in an enclosed area, such as a bookcase  or  drawer  that may impede air flow.

Keep away from sources of heat
This unit should not be exposed to direct heat sources such as a candle, replace, radiator, heat register, stove or other appliance that emits heat. The unit should not be left in direct sunlight.

Power source
This unit should only be used with the adapter included in this package.

Damage requiring service
This unit should be serviced by qualified personnel.

WARNING
IR emitted from this product. Do not stare at operating lamp.

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF .

Product Overview

Package List

Paper Unit Monitor

Power key
Long press to turn on/of the monitor; short press to screen on/of.

Pan/Tilt
Press the key   to enter into the pan/Tilt mode.

Volume + / Up key
Press Volume+ to increase the volume/ To up the camera in the Pan/Tilt mode.

Brightness + / Right key
Press the Brightness+ to increase the brightness/ To right the camera in the Pan/Tilt mode.

OK
Press the OK key to view/scan camera or to confirm.

Volume  / Down key
Press Volume- to decrease the volume/ To down the camera in the Pan/Tilt mode.

Brightness / Left key
Press the Brightness- to decrease the brightness/ To left the camera in the Pan/Tilt mode.

Talk to baby
To talk, press and hold the talk key on the front of the monitor; release to turn it of. Bear in mind that you can’t listen to your baby while you’re talking to them to listen to it, you will have to stop pressing this button.

Menu/Exit

Press short Menu/Exit key the menu will pop up, and press again to EXit. Press and hold the Menu/Exit key around 2 seconds to operate Zoom in/out.

MIC
When talking to the baby, collect the voices of the parents.

Power & Charging   Indicator LED
The LED shows red when charging under the display is turn of state. The LED displays shows orange when charging under the turn on state. The LED displays shows green after the battery is fully charged.

Volume LED
When the baby unit detects the voice, the indicator light will be on, The louder the detected sound, the more lights will light up.

LCD screen
Display the baby’s picture and the adjustment of each button function.

Speaker
Hear the sound from the baby.

Stand
Monitor placement stand.

Reset key under the stand
Long press the reset button with a pin to reset the display.

DC jack
Charge the monitor by connecting the Power Adapter to the monitor and a socket.

Note
If you want to adjust the Volume/Brightness, you have to exit the Pan/Tilt mode before you operate it.

Baby Unit Camera

1. Light sensor
2. Infrared LED
3. CMOS sensor
4. Power LED
5. MIC
6. Speake
7. Pair key
8. DC-Jack
9. Temperature sensor
10. Antenna

ICON OVERVIEWS

Using The Baby Monitor

CHARGING AND POWERING THE MONITOR UNIT

Step1
Charge the monitor by connecting the A/C adapter included in this package to the monitor and a socket. (It takes about 4 hours for the monitor to be fully charged.

Step2
Use the provided AC adapter included in this package to connect the wall outlet with the baby unit.

Note
Place the camera at least 3ft / 1m away from your baby. Gently press and hold the Power Button for 3s to turn on the monitor, then you can see the live view. Follow your needs to adjust the sound, brightness, and reasonable placement of the camera.

Tips
To use the baby monitor, you must be able to establish a radio link between the monitor and camera, and the range will be acted by environmental conditions. Any large metal object, like a refrigerator, a mirror, align cabinet, metallic doors or reinforced concrete between the baby and parent unit may block the radio signal. The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TV, computers, cordless or mobile phones, fluorescent lights or dimmer switches.  When using the other 2.4GHz product, such as wireless networks Wi- Fi routers, Bluetooth systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 5ft(1.5m) from these types of products.

PAN AND TILT

The camera unit can be remotely controlled from the Monitor Unit

Step1
Press the Pan/Tilt key enter the Pan/Tilt mode.

Step2
Press I or to tilt upward or downward.

Step3
Press the or to pan left or right.

Step4
Press the Pan/Tilt key to exit the Pan/Tilt mode.

Note
During the Pan/Tilt can not use the navigation key to adjust volume and brightness.

NIGHT VISION MODE

When the built-in photo sensor detects a low level of ambient light, the screen on the Monitor Unit will display in black and white. the )icon will be displayed on the screen.

TALK MODE

Press and hold the on the Monitor Unit to talk to your baby through the Camera Unit’s loudspeaker. A icon will be displayed at the bottom right corner of the screen.

DICITAL ZOOM

Step1
Press and hold the Menu/Exit key EQ arond 2 seconds enter Zoom mode.

Step2
At the Zoom mode, press the Pan/Tilt key to adjust the direction of the camera/image.

Step3
Press the LEFT key to pan left; Press RIGHT key to pan right; Press UP key I to tilt up; Press Down key to tilt down.

Step4
Press and hold the Menu/Exit key again around 2 seconds to operate Zoom out. During digital zoom mode, the zoom icon will be displayed on the top of screen. Warm reminder: If you want to adjust the Volume/Brightness, you have to exit the Pan/Tilt press Pan/Tilt key  mode before you operate it.

SCAN AND SWITCH THE CAMERAS

Short press key to view/scan camera, during the scan mode. the icon will be displayed on the top of the screen. Each camera’s video will be stay on the LCD around 10 seconds then change to the next camera. Short press the scan key again to switch the camera under the scan mode. Note: This function is only available when two or more cameras are paired.

FUNCTION OVERVIEW

PAIRING THE CAMERA AND MONITOR

Press Menu/Exit key =and the menu will pop up.

Select the camera icon and press OK key to enter into sub-menu, press the LEFT key or RIGHT key to select the camera to be paired

Press OK key to start the pairing. While the screen shows pairing them

Once paired, then the screen will display the image from the camera.

If unsuccessful, please repeat above steps.

DELETE THE CAMERA

Press Menu/ Exit keyE and the menu will pop up.

Select the camera iconand press OK key to enter into sub-me press the LEFT key or RIGHT key to select the camera to be canceled

OK Press OK key and select the icon.

Select YES, the camera will be deleted.

ALULLABY SETTING

You can soothe the baby to sleep by playing a gentle lullaby from the baby unit.

Press Menu/Exit key = and the menu will pop up

Select the lullaby icon and press OK key to enter into sub-menu.

Press the NAVIGATION key to select the lullaby you need. OK Press OK key to confirm. Press the Menu/ Exit key to Exit.

FEEDING TIMER SETTING

You can use the alarm to remind yourself to feed baby/change diapers/ sleep.etc. Press Menu/Exit key = and the menu will pop up.

• OK Select the alarm icon and press OK key to enter into sub-menu.
• Press the NAVIGATION key to select desired alert time.
• OK Press OK key to confirm.
• Press the Menu/Exit key = to Exit.

Fecding Timor Notel: Once the alarm is turned on, alarm icon will displayed on the Screen. Note2: The alarm default setting is OFF. Note3: When the alarm is ringing, press any key on the parent unit to turn the alarm off. Note4: If you don’t turn off the alarm, the alarm will ring for 1 minute. After3 minutes the alarm will ring again for 1 minute. The alarm will ring for 3 times in total, after this the alarm goes off.

VOX SETTING

This mode allows you to control the sound activation of your baby monitor. The VOX default setting is OFF. If there is no sound around the camera within 30 Seconds, it will stop transmitting. The monitor screen turns off when the camera is not transmitting. When the camera detects the sound is louder than set sensitivity level, it will start transmitting the signal to the monitor again change the VOX level, please follow the next instructions: Stepl: Press the Menu/Exit key and the menu will pop up.

Select the VOX icon and press OK key to enter into sub menu.

Press LEFT key or RIGHT key to select the desire level. Press the OK key to confirm. Is Low sensitivity level; the baby have to make a lot of sound before the vox function will be activate. is middle sensitivity level. .ais High sensitivity leve; the baby don’t have to make a lot of sound before the VOX function will be activate

TEMPERATURE SETTINGS

Temperature Alarm Setting

Step1
Press Menu / Exit key and the menu will pop up.

Step2
Select the temperature icon and press OK key to enter into sub menu.

Step3
Press the LEFT key or RIGHT key to select between ℃ or ℉, Follow up on your needs to set the maximum and minimum alarm temperatures.

Step4
Press OK key to confrm.

Step5
Press the Menu / Exit key to Exit.

Temperature Hi/Lo Alert Limits

Step1
Press LEFT key or RIGHT key to select (red) or (green) for Hi/Lo limits settings.

Step2
Press the up key/down key to adjust the Hi limit when (red) is selected.

Step3
Press the up key/down key to adjust the Lo limit when (green) is selected.

Note
The high temperature alarm default setting is 31°C, and the low temperature alarm default is 14’C. When the temperature goes above or below the settings, the temperature icon will display on the screen, It will alert the user by beeps. Press any key on the parent unit to stop beeping and flashing.

SETTING

Language Setting

Step1
Press Menu/Exit key = and the menu will pop up.

Step2
Select the setting icon and press OK key to enter into 99 sub-menu. Language Setting

Step3
Select the language setting and press to enter into sub-menu, select the language you need and press to confirm.

Frequency Setting

Press Menu/Exit key Q and the menu will pop up.

Select the setting icon and press OK key a to enter into sub menu

Select the frequency setting and press to enter into sub-menu, select the 60Hz if you are in North America, Select the 50Hz if you are in EUROPE.

Frequency Setting 50Hz 60Hz Step4: Press the Menu/Exit key to Exit.

Reset Setting

Step1

Press Menu/Exit keyQ and the menu will pop up.

Step2

Select the setting icon and press OK key to enter into sub-menu Reset

Step3

Select the reset setting and press to enter into sub-menu, select YES if you need to reset it.

TECHNICAL DATA

System General

Humidity: 5% to 90% rh. ( relative humidity)

Operating Range| Up to 900 feet straight line and open space
Power adapter| Input: 100-240VAC 50 / 60Hz, 300mA Max

Output: SV, lA

LCD| 5.0 LCD Screen
Rechargeable battery for monitor| Model: 503450; 3.7V, 2100 mAh
Operating time with battery fully

charged (parent unit)

| Up to 12 hours VOX on
Image sensor type| 1/6.5 Color CMOS image sensor
IR LED Type| 940nm

TROUBLE SHOOTING

Product does not switch on

| Confrm that the Camera and Monitor Unit are ON(check power LED indicator).

Confrm that Power adapters are properly connected.

---|---

Reception Interference (static)

| The camera and Monitor Unit may be too far apart.

The battery power may be too low.

Other electronic devices may be interfering with the signal.

The Camera or Monitor Unit may be in close proximity to large metallic objects causing interference.

Use of other 2.4GHz products, such as wireless networks (Wif routers), Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them of if they appear to cause interference.

Camera Unit loses link with the Monitor Unit

| If the Camera Unit is too far away with low reception, move the Camera Unit closer to the Monitor Unit.

Reset both units by disconnecting them from battery and electrical power. Wait about 15 seconds, then reconnect.

Large metallic objects, including doors, refrigerators, mirrors, fling cabinets, and also reinforced concrete, may block the radio signal if between the Camera and Monitor Unit.

The signal strength may be reduced when in close proximity to radio or electrical equipment, such as TVs, computers, cordless or mobile phones, fluorescent lights or dimmer switches.

Use of other 2.4GHz products, such as wireless networks Wif routers Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them of if they appear to cause interference.

Pair the Camera Unit under a diferent channel.

No picture from a Camera Unit

| Check all connections to the camera. Confrm that the adapter is plugged in.

Make sure that the Camera Unit is within range of the monitor.

Confrm that the Camera and Monitor Unit are paired.

No sound from Monitor Unit|

Volume setting may be too low. Adjust to a higher setting.

Picture is black and white

| Night vision LED may be ON. Night vision mode operates in black and white.

Turn on room lights to force monitor out of night vision mode.

---|---

The picture playback is not smooth choppy video with low frame rate

| Try moving the Camera Unit closer to the Monitor Unit

Remove obstructions between the Camera and Monitor Unit.

Use of other 2.4GHz products, such as wireless networks Wif routers

Bluetooth systems, or microwave ovens, may cause interference with this product. Keep Camera and Monitor Unit at least 5ft (1.5m) away from these items, or turn them of if they appear to cause interference.

Noise static, beeping

| Battery power may be too low; recharge battery.

Possible alarm ring alert

Possible out of signal alert.

Noise interference on your Monitor Unit

| Volume may be set too high on the Monitor Unit. Lower volume.

The Camera and Monitor Units may be too close. Move them further apart.

The Camera Unit may be too far away and out of range. Move the Camera Unit closer to the Monitor Unit.

Make sure the Camera and Monitor Units are placed away from other electrical equipment, such as a television, computer or cordless/mobile telephone.

The battery will not

charge

| The Adapter may not be properly connected

Try using the other Adapter included.

Pairing failed

| Make sure that the Adapter is connected to the Camera Unit. Try pairing to another CAM channel.
Video not clear with stagnant spots/malks on the screen|

Make sure there is no dirty on lens

FCC STATEMENTS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CUSTOMER SUPPORT

If you encounter any problems in the process of using the product, please feel free to contact us, we will reply to you within 24 hours and resolve the issue in a way that satisfies you.

SCAN QR CODE

Documents / Resources

| IFAMILY SM651 Digital Wireless Video Baby Monitor with 5.0 Inches Color Screen [pdf] User Manual
SM651TX, 2AZBU-SM651TX, 2AZBUSM651TX, SM651 Digital Wireless Video Baby Monitor with 5.0 Inches Color Screen, SM651, Digital Wireless Video Baby Monitor with 5.0 Inches Color Screen
---|---

References

• iFamily

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>