JBC WSU-9A Wire Stripper Control Unit Instruction Manual
- June 5, 2024
- JBC
Table of Contents
JBC WSU-9A Wire Stripper Control Unit
Packing List
Features
CONNECTION
Connection with WS140
Connection with WS440
Control Process
Work Mode
WSS offers two different working modes. Switch the power on choose between Material Mode and Custom Mode by pressing the button
- Material Mode
- Choose between the different materials by pressing the buttons and to choose between all different material options.
- Custom Mode
- To work on a customized mode, press and then the buttons and to select the power level
Operation
Depending on where the tool is located, the soldering station switches between three different states: Work, Sleep and Hibernation. These states are available for JBCs wire strippers WS140 and WS440.
- Work
- When the wire stripper is lifted from the stand, the cartridges will heat up according to the selected configuration.
- Sleep
- When the wire stripper is in the stand, the power falls after a specified time.
- Hibernation
- After longer periods of inactivity, the power is cut off and the cartridges cool down to room temperature.
Troubleshooting
Station troubleshooting is available on the product page at www.jbctools.com
Material Mode
WSU incorporates predetermined power levels and it also features a customized work mode. It allows you to work on wire insulations made of thermoplastics and thermostable materials such as Teflon1, Kapton2, silicone, rubber, etc.
|
Insulation Material
|
Symbol
|
Power Level
---|---|---|---
Thermoplastics
| Polyvinyl Chloride| PVC| 6%
Polyethylene| PE| 7%
Nylon ¹| PA| 10%
Kynar ²| PVDF| 16%
Tefzel ¹| ETFE| 17%
Thermostable
|
Teflon ¹
| FEP| 16%
PFA| 21%
PTFE| 40%
Ethylene Propylene Rubber|
EPM/EPR
|
44%
Silicone Rubber| SI| 51%
Kapton ¹| PI| 90%
Options included:
Accessories
Pedal P305
It can be used to activate/deactivate the Wire Stipper. Sleep and hibernation
delay has to be set to 0 min. Lift the wire stripper from the stand, press and
hold the pedal to activate them and strip the wire. Once the pedal is relaesed
the wire stripper enters in Hibernation. To reverse the pedal functionality
flip the switch of the connection box.
Flat Screw Driver
To open or fi x the wire stripper srews use JBC Flat Screw Driver Ref.
0023511.
Cartridge Extractor Pliers
To manipulate the cartridges use JBC Cartridge Extractor Pliers Ref.
PLR195. More Information at www.jbctools.com
Removing
Inserting and Positioning
Metal Brush
For cleaning the tips if unwanted material is stuck there. Metal Brush Ref. 0022793.
Maintenance
- Before carrying out maintenance or storage, always allow the equipment to cool and unplug the stand from the station and the tool.
- Clean the station screen with a glass cleaner or a damp cloth.
- Use a damp cloth to clean the casing, the stand and the tool. Alcohol can only be used for cleaning the metal parts.
- Periodically check that the metal parts of the tool and stand are clean so that the station can detect the tool status.
- Maintain tip surface clean in order to ensure a correct stripped wire.
- Periodically check all cables.
- Replace a blown fuse as follows (see specification chart)
- take out the fuse holder and remove the fuse. If necessary use a tool to lever it out.
- Press the new fuse into the fuse holder and reinsert it in the station.
- Replace any defective or damaged pieces. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
SAFTEY
Warning
- Do not touch the blade or the metal parts around.
- Do not allow the blade be close to flammable materials.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved.
- Maintenance must not be carried out by children unless supervised.
- Place the tool on the stand when is not in use.
- Turn off the power when not in use, changing parts or storing.
Caution
- Do not use the Wire Stripper for other applications than wire stripping.
- Do not modify or customize the Wire Stripper.
- Do not hit the blade against workbench to eliminate stripped insulation debris. This behavior would damage the blade.
- Remove power from the tool by holding the plug, not the wires.
- Be careful with the fumes produced when stripping. We recomend to use our fume extractor
Specifications
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>