JVC KD-T925BTS Bluetooth Car Stereo Receiver User Guide

KD-T925BTS / KD-T920BTS / KD-T720BT
CD RECEIVER
Quick Start Guide

For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website:

https://www.jvc.net/cs/car/

For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.
Model No.
Serial No.

CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, the following are reproductions of labels on, or inside the product relating to laser product safety.
JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER 1 IN EFFECT AT THE DATE OF MANUFACTURE.
Location: Top Plate

CALIFORNIA, USA ONLY This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Supplier’s Declaration of Conformity Trade Name: JVC
Products: CD RECEIVER
Model Name: KD-T925BTS/KD-T92OBTS/KD-T72OBT
Responsible Party: JVCKENWOOD USA CORPORATION 4001 Worsham Avenue, Long Beach, CA 90808, U.S.A. PHONE: 1-800-252-5722
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
ISED Caution This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
   Contains Bluetooth Module FCC ID: ZWY88112 IC ID: 12033A-88112
   This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
   CAUTION This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from the person’s body.

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the “Licensed Software”) provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the “User) initially used the Product in which the “Licensed Software” is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such cases, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the “Important Notice concerning the Software” to be provided separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) license to use the Licensed Software within the country of the User. (the country where the User bought the Product (hereinafter the “Country”)
Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed, or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation manual or help file and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates, and upgrades) on the condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Aristide 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicenses for the Licensed Software (hereinafter the “Original Rightholder”), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Aristide 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement unless otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility, and consistency with the certain objectives of the Licensed Software.

Aristide 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon the copyright, patent, or any other intellectual property right that was caused by the User’s use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Artide 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without the approval of the Licensor.
Aristide 8 Termination
In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents, and copies thereof within two (2) weeks from such date of termination.
Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction.

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via the Internet of other communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users, and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-Jansson
Copyright (c) 2009-2012 Petri Lehtinen petri@digip.org Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-JSON
Copyright (c) 2009 Dave Gamble Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-CMP
The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
nanopb
Copyright (c) 2011 Petted Aimonen This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.

shat AUTHOR: Aaron D. Gifford – http://www.aarongifford.com/ Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Posix
Copyright (c) 1990, 1993
The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions, and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: This product includes software developed by the University of California, Berkeley, and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved. Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved. License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.
Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou
Permission to use, copy, modify and distribute this software and its documentation is hereby granted, provided that both the copyright notice and this permission notice appear in all copies of the software, derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation.
CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE.
Carnegie Mellon requests users of this software to return to Software Distribution Coordinator or Software.Distribution@ CS.CMU.EDU School of Computer Science Carnegie Mellon University Pittsburgh PA 15213-3890 any improvements or extensions that they make and grant Carnegie the rights to redistribute these changes. License is also granted to make and use derivative works provided that such works are identified as “derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or referencing the derived work. RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular purpose. It is provided “as is” without express or implied warranty of any kind.
Copyright (c) 1993 Martin Birgmeier All rights reserved. You may redistribute unmodified or modified versions of this source code provided that the above copyright notice and this and the following conditions are retained. This software is provided “as is”, and comes with no warranties of any kind. I shall in no event be liable for anything that happens to anyone/anything when using this software. These notices must be retained in any copies of any part of this documentation and/or software.
T-Kernel 2.0
This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org)
BSD-3-Clause
Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
You may obtain a copy of the license at https://opensource.orgnicenses/BSD-3-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
LFS Subsystem
Copyright The Regents of the University of California. All rights reserved.
You may obtain a copy of the license at https://directory.fsf.org/wiki/License:BSD-4-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Accordo2 Player
Apache License Licensed
under the Apache License,
Version 2.0, January 2004(the “License”);
You may obtain a copy of the license at
http://www.apache.orgnicenses/LICENSE-2.0
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES, OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE, ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Installation/Connection

This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
WARNING

• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
• To prevent short circuits:
  — Insulate unconnected wires with vinyl tape.
  — Be sure to ground this unit to the car’s chassis again after installation.
  — Secure the wires with cable clamps and wrap the vinyl tape around the wires that come into contact with metal parts to protect the wires.

CAUTION

• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
• Connect speakers with a maximum power of more than SOW. If the maximum power of the speakers is lower than SOW, change the [AMP GAIN] setting to avoid damaging the speakers.
• Mount the unit at an angle of less than 300.
• If your vehicle wiring harness does not have the ignition terminal, connect the ignition wire (red) to the terminal on the vehicle’s fuse box which provides a 12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat-dissipating metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching the car’s chassis, then replace the old fuse with one that has the same rating.

Basic procedure

1. Remove the key from the ignition switch, then disconnect the e terminal of the car battery.
2. Connect the wires properly. See “Wiring connection” on page 3.
3. Install the unit to your car. See the following “Installing the unit (in-dash mounting)”.
4. Connect the terminal of the car battery.
5. Press SRC to turn on the power.
6. Detach the faceplate and reset the unit within 5 seconds. See “How to reset” on page 4.
   

Installing the unit (without mounting sleeve)

1. Remove the mounting sleeve and trim plate from the unit.
2. Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available).

**Use only the specified screws. Using the wrong screws might damage the unit.
• Part list (supplied)**
(A) Faceplate (xl)
(B) Trimplate (xl)
(C) Mounting sleeve (xl)
(D) Wiring harness (xl)
(E) Extraction key (x2)

Wiring connection

a). Light blue/yellow: To the steering wheel remote control adapter
b. Brown (not used)
c. Blue: To power antenna
(d). Blue/white: To amplifier
e). Blue/white: Remote (12 V r= 350 mA)
f. Orange/white: Illumination
j. Yellow: Battery 12 V
h. Red: Ignition 12 V| Black: Ground
Gray , Gray/black
Front speaker (right)
White , White/black e: Front speaker (left)
Purple , Purple/black e: Rear speaker (right)
Green , Green/black e: Rear speaker (left)
---|---

Before Use

IMPORTANT

• To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide.
• Please keep the Guide in a safe and accessible place for future reference.

WARNING
Do not operate any function that takes your attention away from safe driving.
**CAUTION
Volume setting:**

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
  General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected. Turn off the unit when parking at a low ceiling area.

Basice (on faceplate)

*1 Only for illustration purposes.

*2 One of the display information supports the Music Synchronization Effect. The illumination color or brightness level of the buttons changes and synchronizes with the music level.

Getting Started

1. Acknowledge the crossover type and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” ‘VOLUME KNOB” ‘TO CONFIRM”.

1. Press the volume knob to acknowledge the current crossover type. Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”
2. Press the volume knob. [YES] is selected for the initial setup.
3. Press the volume knob again. “DEMO OFF” appears.

2. Set the clock and date

1. Press and hold 15
2. Turn the volume knob to select [CLOCK], then press the knob. To adjust the clock
3. Turn the volume knob to select [CLOCK ADJUST], then press the knob.
4. Turn the volume knob to make the settings, then press the knob. Set the time in the order of “Hour” “Minute”.
5. Turn the volume knob to select [CLOCK FORMAT], then press the knob.
6. Turn the volume knob to select [12H] or [24H], then press the knob. To set the date
7. Turn the volume knob to select [DATE SET], then press the knob.
8. Turn the volume knob to make the settings, then press the knob. Set the date in the order of “Day” “Month” “Year”.
9. Press 61°0 to exit.
   To return to the previous setting item, press

3. Set the basic settings

1. Press and hold
2. Turn the volume knob to select an item (see the following table), then press the knob.
3. Repeat step 2 until the desired item is selected or activated.
4. Press to exit.
   To return to the previous setting item, press .

[SYSTEM]|
---|---
[KEY BEEP]| (Not [ON]: applicable when 3-way crossover is selected.) Activates the keypress tone. ; [OFF]: Deactivates.
 [FACTORY RESET]|  [YES]: Resets the settings to default (except the stored station). ; [NO]: Cancels.
 [CLOCK]|  [ON]: The clock turned off. ; time is shown on the display even when the unit is [OFF]: Cancels.
[CLOCK DISPLAY]|
 [ENGLISH]| Select the display language for menu and music information if f[ESPANOL] i applicable. a By default [ENGLISH] is selected.
[FRANCAIS]
[FRANCAIS]

Radio

Search for a station

1. Press SRC repeatedly to select FM or AM.
2. Press to search for a station automatically. (or) Press and hold until “M” flashes, then press repeatedly to search for a station manually.

Settings in memory
You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station…. Press and hold one of the number buttons (1 to 6). (or)

1. Press and hold the volume knob until “PRESET MODE” flashes.
2. Turn the volume knob to select a preset number, then press the knob. “MEMORY” appears once the station is stored.

Select a stored station
Press one of the number buttons (1 to 6). (or)

1.  Press
2. Turn the volume knob to select a preset number, then press the knob.

CD/USB/iPod

Selectable source:

• KD-T925BTS: CD/USB FRONT/USB REAR/iPod FRONT/iPod REAR or iPod BT
• KD-T92OBTS/KD-T72OBT: CD/USB/iPod USB or iPod BT

Start playback

The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone) to the USB input terminal.

• Be sure [USB] is selected for [‘PHONE SETUP] in [USB] menu for listening to iPod/iPhone.

Menu Settings

1. Press and hold to enter menu settings.
2. Turn the volume knob to select an item, then press the knob.
3. Repeat step 2 until the desired item is selected/activated.
4. Press to exit.

To return to the previous setting item, press

• Refer to the INSTRUCTION MANUAL on the following website for a detailed explanation of each item: <httpsliwww.jvc.net/cs/carh
• The availability of each item varies depending on the model.

Menu items [EQ SETTING] [AUDIO CONTROL] [SOUND EFFECT] [DISPLAY] [COLOR] [TUNER SETTING] [SIRIUS XM] [USB] [BT MODE] [REMOTE APP] [ALEXA SETUP] [MIC GAIN]
[NR LEVEL]
[ECHO CANCEL]*
[SYSTEM] [CLOCK] [ENGLISH] [ESPANOL] [FRANCAIS] [DEMO MODE]| Selects a preset equalizer or adjust your own sound settings.
Sets your preferred audio settings.
Sets your preferred sound effect.
Sets your preferred control for the display window.
Sets your preferred illumination color for buttons.
Settings for radio source. Settings for Sirius XM tuner.
Sets iPod/iPhone playback source (via USB input terminal or via Bluetooth).
Settings for using a Bluetooth device. Settings for using smartphones to control this unit.
Sets your preferred voice control language for Alexa. Sets the sensitivity of the microphone.
Adjusts the noise reduction level.
Adjusts the echo cancellation delay time.
Settings for this unit.
Adjusts the clock.
Select language for the menu and music information.
Select language for the menu and music information.
Select language for the menu and music information.
Activates or deactivates the display demonstration.
---|---

• Applicable only while talking on the phone.
  Examples of some well-used settings
  Subwoofer Level Setting

  1. Press and hold to enter menu settings.

  2. Turn the volume knob clockwise to select [AUDIO CONTROL], then press the knob.

  3. Turn the volume knob clockwise to select [SUBWOOFER SET], then press the knob.

  4. Turn the volume knob clockwise to select [ON], then press the knob.

  5. Turn the volume knob clockwise to select [SUB.W LEVEL], then press the knob.

  6. Press the volume knob if [PRE-OUT] is shown on the display.

  7. Turn the volume knob to adjust the subwoofer level, then press the knob.

  8. Press 5-0 to exit the setting menu.

Note: For KD-T920BTS/KD-T720BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings.
Illumination Color Setting
For KD-T925BTS/KD-T92OBTS, you can set your preferred illumination color for each zone.

1. Press and hold to enter menu settings.

2. Turn the volume knob clockwise to select [COLOR], then press the knob.

3. Press the volume knob if [PRESET] is shown on the display.

4. Turn the volume knob to choose a zone ([ALL ZONE], [ZONE 1], [ZONE 2]), then press the knob.

5. Turn the volume knob to choose a color, then press the knob.

• [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
• [COLOR FLOWO1] to [COLOR FLOW03]: Color changes at different speeds.
• [CRYSTAL]/[FLOWER]/[FOREST]/[GRADATION]/[OCEAN]/ [RELAX]/[SUNSET]: The selected color pattern is shown. (Selectable only when [ALL ZONE] is selected in step 4.)

6. Repeat step 4 and step 5 to set color for other zones.
7. Press to exit.

Other Information

For playback operations of AUX, SiriusXM® Radio and AMAZON ALEXA sources, refer to the INSTRUCTION MANUAL on the following website: <https://www.jvc.net/cs/carh
• The availability of each source vary depending on the model.

Note for specifications
Bluetooth Frequency Range: 2.402 GHz — 2.480 GHz
Bluetooth RF Output Power (E.I.R.P.):
+4 dBm (MAX), Power Class 2 Speaker Impedance:
4Ω — 8Ω
Operating Voltage:
12 V DC car battery

Bluetooth®

• Depending on the Bluetooth version, operating system, and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Be sure to turn on the Bluetooth function of the device to make the following operations.
• Signal conditions vary depending on the surroundings.

Connect the microphone
Connect the supplied microphone to the microphone input jack on the rear panel.

Pair and connect a Bluetooth device for the first time

1. Press OSRC to turn on the unit.
2. Search and select the name of your receiver (“KD-T92SBTS”/ “KD-T92OBTS”/”KD-T72OBT”) on the Bluetooth device.
3. Perform (A) or (B) depending on what appears on the display. For some Bluetooth devices, pairing sequence may vary from the steps described below.

“XXXXXX” is a 6-digit passkey randomly generated during each pairing.

1. Ensure that the passkeys appear on the unit and Bluetooth device are the same.
2. Press the volume knob to confirm the passkey.
3. Operate the Bluetooth device to confirm the passkey.

(B) “[Device Name]” “VOL – YES” “BACK – NO”

Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device.
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “ ****” will light up when the Bluetooth connection is established.

Answer a call

Press or the volume knob.

• To adjust the phone volume [00] to [35], turn the volume knob.
• To end a call, press and hold or the volume knob.

Audio player via Bluetooth

1. Press SRC repeatedly to select BT AUDIO.
2. Operate the audio player via Bluetooth to start playback.

• Windows Media is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by the certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.
• Apple, iPhone, iPod, iPod touch, and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.
• 105 is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
• SiriusXM and all related marks and logos are trademarks of Sirius XM Radio, Inc. All rights reserved.
• Android is a trademark of Google LLC.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
• Amazon, Alexa and all related marks are trademarks of Amazon.com, Inc. or its affiliates.
• Alexa is not available in all languages and countries. Alexa features and functionality may vary by location.

© 2022 JVCKENWOOD Corporation
0322DTSMDTJEIN

References

• Amazon.com
• Roundcube Webmail :: Welcome to Roundcube Webmail
• Welcome to www.aarongifford.com - The Web Site of Aaron D. Gifford
• Apache License, Version 2.0
• dtsc.ca.gov/hazardouswaste/perchlorate
• TRON Forum
• License:BSD-4-Clause - Free Software Directory
• The 3-Clause BSD License – Open Source Initiative
• Car Electronics Support Information | JVC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>