JBC RHT-A Rework Hand Support Instruction Manual

: June 5, 2024
: JBC

Table of Contents

JBC RHT-A Rework Hand Support
Packing List
Assembly
Height Adjustment
Maintenance
Work Position Adjustment
Safety
Specifications
Documents / Resources

JBC RHT-A Rework Hand Support

JBC RHT-A Rework Hand Support Instruction PRODUCT
IMAGE

Packing List

The following items are included:

Tool Arm ……………………. 1 unit
Flange ……………………….. 1 unit
Ref. 0017524
Shaft …………………… 1 unit
Flange Screw ….. 3 u
Ref. 0017548
Flange Nut ……..3 u
Ref. 0892422
Flange Washer .. 3 u
Ref. 0919480
Allen key ……… 1 unit
Ref. 0013609
Height adj. Knob……….. 1 unit
Ref. 0023991
Allen screw………………… 1 unit
Ref. 0017057
Manual………………… 1 unit
Ref. 0023893

Assembly

Fixing the Flange

Fix the flange on your work table with the supplied screws, nuts and washers.
Setting up the Tool Arm

Fit the tool arm onto the base and tighten the screw.
The tool arm position should be like the image according with the letter back of the arm support.

Height Adjustment

The RHT-A Arm allows adjustment for different heights according to your work needs through the vertical axis.
Slide the arm to the appropriate height and secure by tightening the knob to guarantee stability.

Maintenance

Keep the sliding parts clean

Maintenance

Check periodically that the RHT-A is clean, especially the sliding parts and the shaft.
Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.
Replace any defective damaged parts. Use original JBC spare parts only.

Not leave up the RHT-A over the PH when PH is working.

Work Position Adjustment

The RHT-A arm allows adjustment for different positions according to your work needs. The articulated arm covers all work areas.

Work Position Adjustment 01

Work Position Adjustment 02

Position the arm and tighten the knobs.

See the work correct position of the hand in the following images.

Work Position Adjustment 03

Work Position Adjustment 04 Accessories

Ideal for working with JBC’s Hot Air stations and a Preheater.

Accessories

Rework Left Arm Support Ref. HRL-A
Shaft for Hot Air Heater Arm Ref. 0024369
Hot Air Heater Arm Ref. 0024368
IR Preheater Support Ref. PHB-SA

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions.

Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause fire.
The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
Be careful with the fumes produced when soldering.
Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
Not leave up the arms directly above heat surfaces.
Utmost care must be taken with liquid tin waste which can cause burns.
This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
Maintenance must not be carried out by children unless supervised.

Specifications

Total weight: 1,5 kg (33.1 lb)
Base dimensions: 270 x 410 mm (10.6 x 16.2 in)
Height: 205 mm (8.1 in)
Arm length: 498,1 mm (19.6 in)
ESD safe connector

Complies with CE standards ESD Safe

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labor.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com