JBC DR560-A Desoldering Iron Instruction Manual
- June 5, 2024
- JBC
Table of Contents
DR560-A Desoldering Iron
Instruction Manual
Packing List
The following items should be included:
Connection
Desoldering process
Use a tip with a larger diameter than the pad to achieve maximum aspiration and thermal efficiency.
| |
---|---|---
Place the tip with the component terminal in the hole.| When the solder
liquefies, gently rotate the tip so that the compo nent terminal can be lifted
off.| Press the vacuum pump button long enough to remove the solder.
After pressing the desoldering key there is a slight delay until the self- contained vacuum pump stops. This makes sure that the vacuum circuit is completely empty. If any solder remains are left on a terminal after desoldering it, resolder it with fresh solder and repeat the desoldering operation.
Changing Tips
This operation should be done while the tip is hot and at a minimum temperature of 250°C, so that any tin left inside is still molten.
Removing
Use the special spanner to unscrew the tip.
Inserting
Fit the new tip and tighten with the spanner 0to make sure it is air tight.
Compatible Tips
The DR560 uses C560 tips.
Find the model that best suits your soldering needs in
www.jbctools.com Here are some C560 tips in real
size:
Changing the heating element (Ref. DSV-DR)
For this operation, turn off the station or disconnect the tool and wait until the tool temperature drops to room temperature.
Removing
Loosen the deposit lid (a), remove the screw (b) and withdraw the heating
element (c).
Placing
Insert the new Heating Element (a), tighten the screw (b) and then the lid
(c).
Before placing, make sure to insert the internal gasket into the Glass Solder Collector.
Important
For a proper connection it is essential to insert the cartridge by lining it
up to the mark▶ .
Compatibility
The DSV-DR also works with the previous version DR5600 Desoldering Iron
(Ref. 5600010).
In this case, you must take out the washer with a pliers.
Glass Solder Collector Cleaning
Removing the lid
The lid must be unscrewed with the DR560 in a vertical position.
Cleaning
Remove the coil and clean the inside of the glass solder collector with the cleaning stick.
Check the filter and replace it if it is dirty or damaged.
Inserting the glass solder collector
The glass solder collector must be inserted with coil filter in place, positioned between the 2 lines marked.
Then the whole unit must be closed by screwing the lid.
Tip Care
The intake tube should be periodically cleaned by the largest rod.
Important
DO NOT press the vacuum pump button while tinning the desoldering tip, as the
fumes given off by the flux would quickly block the ducts and the air filter.
Maintenance
Before carrying out maintenance or storage, always unplug the tool.
-
Check periodically that the metal parts are clean to ensure it is detected when on the stand.
Always use a damp cloth or alcohol. -
Periodically check all cables and tubes connections.
-
Replace any defective or damaged pieces. Use original JBC spare parts only.
-
Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to protect health and prevent electric shock, injury, fire or explosions.
- Do not use the tool for any purpose other than soldering or rework. Incorrect use may cause fire.
- The mains cable must be plugged into approved bases. Make sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Do not leave the appliance unattended when it is on.
- It is necessary to turn the station off before changing tips.
- Heat can cause inflamable products to ignite even when out of sight.
- Be careful with the remains of liquid tin. In contact with skin, it can cause burns.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
- This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
- Weight: 413 g (0.91 lb)
Complies with CE standards.
ESD protected.
Exploded View · Despiece
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour. Warranty does not
cover product wear or misuse. In order for the warranty to be valid,
equipment must be returned, postage paid, to the dealer where it was
purchased. Please register your warranty within 30 days of purchase in
www.jbctools.com/productregistration.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of their life must be collected and returned to an authorized
recycling facility.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>