Shenzhen Jinlishun Technology FS-098 Alarm Clock with Wireless Charging Instruction Manual

Shenzhen Jinlishun Technology FS-098 Alarm Clock with Wireless Charging

Box contents

Controls & Features

• Time, Dimmer, Snooze
• Button, 1Alarm 1 set/-Taste
• LED Display
• Button, 42 Alarm set/-Taste
• Wireless charging zone
• USB C power port
• Back up the battery compartment

LED Indicators

• PM (12-hour clock)
• Wireless charging indicator
• 1 Alarm 1 on
• 2 Alarm 1 on
• Zz Snooze

Power connection

Fitting a backup battery

The Slick has a backup battery feature where a 1x CR2025 battery (not supplied) will allow it to remember time and alarm settings if unplugged or power is cut.
Please Note: The battery will not power the clock or wireless charging function it will only save settings.

Insert 1x CR2025 battery (not supplied)

The Slick has a backup battery feature where a 1x CR2025 battery (not supplied) will allow it to remember time and alarm settings if unplugged or power is cut. Please Note: The battery will not power the clock or wireless charging function it will only save settings.

Clock setting

• 12H/24H
• Hour

**Minute

**

Alarm Setting

• Alarm 1-Hour

• Alarm 1-Minute
• Alarm 1-enable-disable
• Alarm 2-Hour
• Alarm 2-Minute
• Alarm 2-enable/disable

SPECIFICATION

Power Input USB C:|

SV= lA,

SV = 2A v SW Charging SV= 3A,

9V = 2A V 1OW Charging

---|---
Backup battery:|

lx 3V CR2O25 Lithium

Wireless charging/ 9V = 2A Input|

1OWmax.

Wireless charging/ 9V = 2A Input|

SW max.

Dimensions, Diameter x Height|

134x 52.6 mm

Wireless charging

If you have a phone with Qi wireless charging capability you can use your Slick to charge it. Place your smartphone centrally capability you can use your Slick to charge it. The wireless charging LED (9) in the bottom left of the LCD panel is lit while your phone is charging and the battery charge status can be seen on your phone’s display.
Please Note: The wireless charging LED (9) will flash if your phone is not correctly positioned. You may need to remove your smartphone from its case if the thickness of the case exceeds 5mm or if contains metal.

Caring for your Alarm

Clock Important Safety Information Important
Please read these instructions fully before installing or operating your alarm clock. Keep away from flame sources such as lighted candles. Do not expose to dripping or splashing fluids. Objects filled with liquids, such as vases, must not be placed close to the speaker. The unit should not be exposed to direct sunlight, very high or low temperature, moisture, vibrations, strong magnetic fields, high frequencies, and dusty environments. Do not place the product in enclosed bookcases or racks without proper ventilation. Ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. Never attempt to insert wires, pins, or other such objects into the vents or openings of the unit. Do not disassemble or modify the alarm clock, there are no user-serviceable parts. If the alarm clock is damaged in any way or malfunctions do not use it. Consult a qualified service engineer. Do not use abrasives, benzene, thinner, or other solvents to clean the surface of the unit. To clean, wipe with clean soft cloth and a mild detergent solution. This product uses batteries and both the product and batteries must be disposed of properly. Do not throw them in the household waste at the end of their life cycle; take them to a collection center for the recycling of electrical, and electronic equipment, and batteries. Contact your local council for recycling advice.

Troubleshooting

Alarm doesn’t switch on

| Check USB cable is connected properly to Slick and powered USB port
CheckUSB power input is switched on
No LED display| Check dimmer is not set to OFF
Wireless charging is very slow| Connect Slick to 9V=2A power adaptor

After power cut, time and alarm settings don’t reset

| No backup battery fitted – Insert CR2025 battery
Backup battery incorrectly fitted – insert properly see diagram

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instructions, specifications, and pictures in this documentation may differ slightly from your particular situation. All items described in this guide are for illustration purposes only and may not apply to your particular situation. No legal rights or entitlements may be obtained from the description made in this manual.

Declaration of conformity

Hereby, Philex Electronic Ltd declares that the wireless charging equipment: Slick Alarm Clock is in compliance with the Radio Equipment Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: www.philex.com/doc

Technical support

For further help, advice, information, or live chat visit: www.iboxstyle.com

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is Subject To the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV technician for

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>